scholarly journals Transverse and Oblique Long Bone Fracture Evaluation by Low Order Ultrasonic Guided Waves: A Simulation Study

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Ying Li ◽  
Dan Liu ◽  
Kailiang Xu ◽  
Dean Ta ◽  
Lawrence H. Le ◽  
...  
Keyword(s):  
Fracture Healing ◽  
Bone Fracture ◽  
Guided Waves ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Fdtd Simulation ◽  
Long Bones ◽  
Fracture Angle ◽  
Wave Modes ◽  
Low Order

Ultrasonic guided waves have recently been used in fracture evaluation and fracture healing monitoring. An axial transmission technique has been used to quantify the impact of the gap breakage width and fracture angle on the amplitudes of low order guided wave modesS0andA0under a 100 kHz narrowband excitation. In our two dimensional finite-difference time-domain (2D-FDTD) simulation, the long bones are modeled as three layers with a soft tissue overlay and marrow underlay. The simulations of the transversely and obliquely fractured long bones show that the amplitudes of bothS0andA0decrease as the gap breakage widens. Fixing the crack width, the increase of the fracture angle relative to the cross section perpendicular to the long axis enhances the amplitude ofA0, while the amplitude ofS0shows a nonmonotonic trend with the decrease of the fracture angle. The amplitude ratio between theS0andA0modes is used to quantitatively evaluate the fracture width and angles. The study suggests that the low order guided wave modesS0andA0have potentials for transverse and oblique bone fracture evaluation and fracture healing monitoring.

Ultrasonic Guided Wave Testing of Finned Tubing

2015 ◽  
Author(s):  
Owen M. Malinowski ◽  
Matthew S. Lindsey ◽  
Jason K. Van Velsor
Keyword(s):  
Wave Propagation ◽  
Guided Waves ◽  
Tube Wall ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Complex Nature ◽  
Inspection Method ◽  
Ultrasonic Guided Wave ◽  
Guided Wave Propagation ◽  
Wave Modes

In the past few decades, ultrasonic guided waves have been utilized more frequently Non-Destructive Testing (NDT); most notably, in the qualitative screening of buried piping. However, only a fraction of their potential applications in NDT have been fully realized. This is due, in part, to their complex nature, as well as the high level of expertise required to understand and utilize their propagation characteristics. The mode/frequency combinations that can be generated in a particular structure depend on geometry and material properties and are represented by the so-called dispersion curves. Although extensive research has been done in ultrasonic guided wave propagation in various geometries and materials, the treatment of ultrasonic guided wave propagation in periodic structures has received little attention. In this paper, academic aspects of ultrasonic guided wave propagation in structures with periodicity in the wave vector direction are investigated, with the practical purpose of developing an ultrasonic guided wave based inspection technique for finned tubing. Theoretical, numerical, and experimental methods are employed. The results of this investigation show excellent agreement between theory, numerical modeling, and experimentation; all of which indicate that ultrasonic guided waves will propagate coherently in finned tube only if the proper wave modes and frequencies are selected. It is shown that the frequencies at which propagating wave modes exist can be predicted theoretically and numerically, and depend strongly on the fin geometry. Furthermore, the results show that these propagating wave modes are capable of screening for and identifying the axial location of damage in the tube wall, as well as separation of the fins from the tube wall. The conclusion drawn from these results is that Guided Wave Testing (GWT) is a viable inspection method for screening finned tubing.

scholarly journals Numerical Investigation of Excitation of Various Lamb Waves Modes in Thin Plastic Films

2022 ◽  
Vol 12 (2) ◽  
pp. 849
Author(s):  
Rymantas Jonas Kazys ◽  
Justina Sestoke ◽  
Egidijus Zukauskas
Keyword(s):  
Numerical Investigation ◽  
Lamb Wave ◽  
Guided Waves ◽  
Phased Array ◽  
Ultrasonic Transducer ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Plastic Films ◽  
Thin Plastic ◽  
Wave Modes

Ultrasonic-guided waves are widely used for the non-destructive testing and material characterization of plates and thin films. In the case of thin plastic polyvinyl chloride (PVC), films up to 3.2 MHz with only two Lamb wave modes, antisymmetrical A0 and symmetrical S0, may propagate. At frequencies lower that 240 kHz, the velocity of the A0 mode becomes slower than the ultrasonic velocity in air which makes excitation and reception of such mode complicated. For excitation of both modes, we propose instead a single air-coupled ultrasonic transducer to use linear air-coupled arrays, which can be electronically readjusted to optimally excite and receive the A0 and S0 guided wave modes. The objective of this article was the numerical investigation of feasibility to excite different types of ultrasonic-guided waves, such as S0 and A0 modes in thin plastic films with the same electronically readjusted linear phased array. Three-dimensional and two-dimensional simulations of A0 and S0 Lamb wave modes using a single ultrasonic transducer and a linear phased array were performed. The obtained results clearly demonstrate feasibility to excite efficiently different guided wave modes in thin plastic films with readjusted phased array.

scholarly journals A Graphical Analysis Method of Guided Wave Modes in Rails

2019 ◽  
Vol 9 (8) ◽  
pp. 1529 ◽  
Author(s):  
Xining Xu ◽  
Bo Xing ◽  
Lu Zhuang ◽  
Hongmei Shi ◽  
Liqiang Zhu
Keyword(s):  
Image Processing ◽  
Guided Waves ◽  
Wave Mode ◽  
Graphical Analysis ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Mode Shapes ◽  
Analysis Method ◽  
Processing Methods ◽  
Wave Modes

The cross-section of a rail has a complex geometry, and there are many propagating modes of ultrasonic guided waves in a rail. The analysis of mode shapes or the cross-sectional wave structure is of high significance to the design of an appropriate wave excitation approach for long-range defect detection of a rail. Traditionally, the semi-analytical finite elements (SAFE) method is used to obtain ultrasonic guided waves’ dispersion curves of a rail. Then, through solving the eigenvectors, it is able to calculate the displacement values of discrete nodes in three degrees of freedom (DOFs) and further obtain the wave structures. In this paper, a graphical analysis method of guided wave mode shapes is proposed. The displacements of each node in three DOFs are converted into Red Green Blue (RGB) image pixels, and the complex vibration vector data is expressed by an image. Therefore, the graphical analysis of mode shapes can be realized by using conventional image processing methods without the design of special data processing algorithms. This will improve the processing efficiency, and it is more intuitive and easier to analyze the vibration displacements represented by the image. The simulation results show that the proposed graphical analysis method can quickly and precisely locate the excitation position of the guided wave mode in the rail. By adopting image processing methods, such as the K-means clustering algorithm, the guided wave modes at a 35 kHz frequency in a rail are classified according to their mode shapes. Classification is essential for exploring the relations and fundamentals of vibrations in modes. The graphical analysis method proposed in this paper provides a novel method for the mode analysis of guided waves in rails.

Contribution of Lamb wave modes in the formation of higher order modes cluster (HOMC) guided waves

2021 ◽  
pp. 095440622110424
Author(s):  
Z Abbasi ◽  
F Honarvar
Keyword(s):  
Finite Element ◽  
Wave Packet ◽  
Lamb Wave ◽  
Guided Waves ◽  
Element Model ◽  
Higher Order ◽  
Guided Wave ◽  
Cross Sectional ◽  
Higher Order Modes ◽  
Wave Modes

In recent years, Higher Order Modes Cluster (HOMC) guided waves have been considered for ultrasonic testing of plates and pipes. HOMC guided waves consist of higher order Lamb wave modes that travel together as a single nondispersive wave packet. The objective of this paper is to investigate the effect of frequency-thickness value on the contribution of Lamb wave modes in an HOMC guided wave. This is an important issue that has not been thoroughly investigated before. The contribution of each Lamb wave mode in an HOMC guided wave is studied by using a two-dimensional finite element model. The level of contribution of various Lamb wave modes to the wave cluster is verified by using a 2D FFT analysis. The results show that by increasing the frequency-thickness value, the order of contributing modes in the HOMC wave packet increases. The number of modes that comprise a cluster also increases up to a specific frequency-thickness value and then it starts to decrease. Plotting of the cross-sectional displacement patterns along the HOMC guided wave paths confirms the shifting of dominant modes from lower to higher order modes with increase of frequency-thickness value. Experimental measurements conducted on a mild steel plate are used to verify the finite element simulations. The experimental results are found to be in good agreement with simulations and confirm the changes observed in the level of contribution of Lamb wave modes in a wave cluster by changing the frequency-thickness value.

scholarly journals Fatigue crack detection in pipes with multiple mode nonlinear guided waves

2018 ◽  
Vol 18 (1) ◽  
pp. 180-192 ◽  
Author(s):  
Ruiqi Guan ◽  
Ye Lu ◽  
Kai Wang ◽  
Zhongqing Su
Keyword(s):  
Fatigue Crack ◽  
Crack Detection ◽  
Guided Waves ◽  
Second Harmonic ◽  
Experimental Testing ◽  
Harmonic Wave ◽  
Guided Wave ◽  
Element Analysis ◽  
Fatigue Crack Detection ◽  
Wave Modes

This study elaborates fundamental differences in fatigue crack detection using nonlinear guided waves between plate and pipe structures and provides an effective approach for analysing nonlinearity in pipe structures. For this purpose, guided wave propagation and interaction with microcrack in a pipe structure, which introduced a contact acoustic nonlinearity, was analysed through a finite element analysis in which the material nonlinearity was also included. To validate the simulation results, experimental testing was performed using piezoelectric transducers to generate guided waves in a specimen with a fatigue crack. Both methods revealed that the second harmonic wave generated by the breathing behaviour of the microcrack in a pipe had multiple wave modes, unlike the plate scenario using nonlinear guided waves. Therefore, a proper index which considered all the generated wave modes due to the microcrack was developed to quantify the nonlinearity, facilitating the identification of microscale damage and further assessment of the severity of the damage in pipe structures.

Phase velocity estimation technique based on adaptive beamforming for ultrasonic guided waves propagating along cortical long bones

2017 ◽  
Vol 56 (7S1) ◽  
pp. 07JF06 ◽  
Author(s):  
Shigeaki Okumura ◽  
Vu-Hieu Nguyen ◽  
Hirofumi Taki ◽  
Guillaume Haïat ◽  
Salah Naili ◽  
...  
Keyword(s):  
Phase Velocity ◽  
Guided Waves ◽  
Adaptive Beamforming ◽  
Velocity Estimation ◽  
Ultrasonic Guided Waves ◽  
Long Bones ◽  
Estimation Technique

scholarly journals Numerical and Experimental Investigation of Guided Wave Propagation in a Multi-Wire Cable

2019 ◽  
Vol 9 (5) ◽  
pp. 1028 ◽  
Author(s):  
Pengfei Zhang ◽  
Zhifeng Tang ◽  
Fuzai Lv ◽  
Keji Yang
Keyword(s):  
Wave Energy ◽  
Guided Waves ◽  
Wave Structure ◽  
Excitation Power ◽  
Dispersion Analysis ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Mechanical Coupling ◽  
Guided Wave Propagation ◽  
Contact Acoustic Nonlinearity

Ultrasonic guided waves (UGWs) have attracted attention in the nondestructive testing and structural health monitoring (SHM) of multi-wire cables. They offer such advantages as a single measurement, wide coverage of the acoustic field, and long-range propagation ability. However, the mechanical coupling of multi-wire structures complicates the propagation behaviors of guided waves and signal interpretation. In this paper, UGW propagation in these waveguides is investigated theoretically, numerically, and experimentally from the perspective of dispersion and wave structure, contact acoustic nonlinearity (CAN), and wave energy transfer. Although the performance of all possible propagating wave modes in a multi-wire cable at different frequencies could be obtained by dispersion analysis, it is ineffective to analyze the frequency behaviors of the wave signals of a certain mode, which could be analyzed using the CAN effect. The CAN phenomenon of two mechanically coupled wires in contact was observed, which was demonstrated by numerical guided wave simulation and experiments. Additionally, the measured guided wave energy of wires located in different layers of an aluminum conductor steel-reinforced cable accords with the theoretical prediction. The model of wave energy distribution in different layers of a cable also could be used to optimize the excitation power of transducers and determine the effective monitoring range of SHM.

scholarly journals Shear-Actuation and Vibrometer Reception of Penetrating Ultrasonic Guided Wave Modes in Human Tibia

2020 ◽  
Vol 10 (23) ◽  
pp. 8397
Author(s):  
Anurup Guha ◽  
Michael Aynardi ◽  
Parisa Shokouhi ◽  
Cliff J. Lissenden
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Phase Velocity ◽  
Time Domain ◽  
Guided Waves ◽  
Ultrasonic Guided Waves ◽  
Appendicular Skeleton ◽  
Element Analysis ◽  
Human Tibia ◽  
Wave Modes

The hollow long bones of the human appendicular skeleton are known to support the propagation of ultrasonic guided waves, whose potential for diagnosing bone health is being investigated. In this study, ultrasonic guided waves propagating in the diaphysis of human tibia are characterized experimentally and numerically in the frequency range around 200 kHz. The experiment involves a unique combination of omni-directional shear transducer-based excitation and detection using a 1D laser Doppler vibrometer. The cluster of phase velocities obtained from a linear array of time-history data using space-time Fourier transform is found to be in the non-dispersive low-phase velocity region of the dispersion curves obtained for a tibial cross-section. Time-domain finite element analysis revealed that the displacement components normal to the surface are significant, even though the loading is from a shear transducer. Furthermore, semi-analytical finite element analysis revealed that the wave structures of the wave modes contained within the cluster of low-phase velocity modes are consistent with the displacement profiles obtained from the time-domain analysis. The experimental results show that the low-phase velocity mode cluster has sufficient intensity to propagate axially at least 85 mm in the mid-diaphyseal region.

Warped frequency transform analysis of ultrasonic guided waves in long bones

2010 ◽  
Author(s):  
L. De Marchi ◽  
E. Baravelli ◽  
K. Xu ◽  
D. Ta ◽  
N. Speciale ◽  
...  
Keyword(s):  
Guided Waves ◽  
Ultrasonic Guided Waves ◽  
Long Bones

scholarly journals Excitation and Propagation of Longitudinal L (0, 2) Mode Ultrasonic Guided Waves for the Detection of Damages in Hexagonal Pipes: Numerical and Experimental Studies

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Xiang Wan ◽  
Meiru Liu ◽  
Xuhui Zhang ◽  
Hongwei Fan ◽  
Qinghua Mao ◽  
...  
Keyword(s):  
Guided Waves ◽  
Experimental Studies ◽  
Special Kind ◽  
Dispersion Curves ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Resource Exploitation ◽  
Ultrasonic Guided Wave ◽  
Study Results ◽  
Through Hole

The hexagonal pipe is a special kind of tube structure. Its inner surface of the cross section is in the shape of circle, while the outer surface is hexagonal. It has functioned as an essential and critical part of a drill stem in a high-torque drill machine used in various resource exploitation fields. The inspection of a hexagonal pipe to avoid its failure and thus to ensure safe operation of a drilling machine is becoming increasingly urgent and important. In this study, the excitation and propagation of ultrasonic guided waves for the purpose of detecting defects in hexagonal pipes are proposed. Dispersion curves of hexagonal pipes are firstly derived by using semianalytical finite element method. Based on these dispersion curves, longitudinal L (0, 2) mode at 100 kHz is selected to inspect hexagonal pipes. A ring of piezoelectric transducers (PZTs) with the size of 25 mm × 5 mm ×0.5 mm is able to maximize the amplitude of L (0, 2) mode and successfully suppress the undesired L (0, 1) mode in the experiments. Numerical and experimental studies have shown that the displacement field of L (0, 2) mode at 100 kHz is almost uniformly distributed along the circumferential direction. Furthermore, L (0, 2) mode ultrasonic guided waves at 100 kHz are capable of detecting circular through-hole damages located in the plane and near the edge in a hexagonal pipe. Our study results have demonstrated that the use of longitudinal L (0, 2) mode ultrasonic guided wave provides a promising and effective alternative for the detection of defects in hexagonal pipe structures.

Sign in / Sign up

Export Citation Format

Share Document