scholarly journals Effect of Airborne Particle Abrasion on Microtensile Bond Strength of Total-Etch Adhesives to Human Dentin

2017 ◽  
Vol 2017 ◽  
pp. 1-7 ◽  
Author(s):  
Maurizio D’Amario ◽  
Chiara Piccioni ◽  
Stefano Di Carlo ◽  
Francesca De Angelis ◽  
Silvia Caruso ◽  
...  
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Adhesive System ◽  
Mode Analysis ◽  
Airborne Particle ◽  
Microtensile Bond Strength ◽  
Failure Data ◽  
Multiple Beams ◽  
Failure Mode Analysis ◽  
Human Dentin

Aim of this study was to investigate a specific airborne particle abrasion pretreatment on dentin and its effects on microtensile bond strengths of four commercial total-etch adhesives. Midcoronal occlusal dentin of extracted human molars was used. Teeth were randomly assigned to 4 groups according to the adhesive system used: OptiBond FL (FL), OptiBond Solo Plus (SO), Prime & Bond (PB), and Riva Bond LC (RB). Specimens from each group were further divided into two subgroups: control specimens were treated with adhesive procedures; abraded specimens were pretreated with airborne particle abrasion using 50 μm Al2O3before adhesion. After bonding procedures, composite crowns were incrementally built up. Specimens were sectioned perpendicular to adhesive interface to produce multiple beams, which were tested under tension until failure. Data were statistically analysed. Failure mode analysis was performed. Overall comparison showed significant increase in bond strength (p<0.001) between abraded and no-abraded specimens, independently of brand. Intrabrand comparison showed statistical increase when abraded specimens were tested compared to no-abraded ones, with the exception of PB that did not show such difference. Distribution of failure mode was relatively uniform among all subgroups. Surface treatment by airborne particle abrasion with Al2O3particles can increase the bond strength of total-etch adhesives.

Shear Bond Strength of Different Adhesive Systems to Primary Dentin and Enamel

2007 ◽  
Vol 31 (1) ◽  
pp. 35-40 ◽  
Author(s):  
Carla Miranda ◽  
Luiz Henrique Maykot Prates ◽  
Ricardo de Souza Vieira ◽  
Maria Cristina Marino Calvo
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Shear Bond Strength ◽  
Adhesive System ◽  
Mode Analysis ◽  
Single Bond ◽  
Adhesive Systems ◽  
Mean Values ◽  
Failure Mode Analysis ◽  
Distal Direction

The aims of this study were to evaluate the shear bond strength (SBS) of four adhesive systems applied to primary dentin and enamel and verify, after SBS testing, the failure mode of the adhesive interface. Sixty extracted sound primary molars were selected and crowns were sectioned in a mesial-distal direction. Specimens were randomly assigned into two groups (adhesion to enamel and adhesion to dentin) and then subdivided into four subgroups according to the adhesive system (n=15): Scotchbond Multi-Purpose (SMP) – Single Bond (SB) – Clearfil SE Bond (and Adper Prompt LPop (APL) – SBS tests were performed and the obtained values were statistically analyzed using ANOVA and Tukey tests (p&lt;0.05). The failure mode analysis was performed with a Scanning Electron Microscope (XL-30, Philips). SBS mean values on enamel were [MPa (SD)]: SMP – 27.89 (7.49); SB – 23.92 (8.8); CSB – 24.36 (6.69); APL – 25.96 (4.08); and on dentin: SMP – 17.29 (4.25); SB – 18.2 (8.74); CSB – 16.13 (7.14); APL – 6.04 (3.35). The predominant failure mode was cohesive (primarily of the bonding agent). On enamel SBS was statistically similar for all four adhesives. On dentin SBS of APL was lower than the other tested adhesives.

scholarly journals Microtensile Bond Strength of Etch-and-Rinse Adhesives in Different Hydroabrasion Conditionings

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Michele Tepedino ◽  
Maciej Iancu Potrubacz ◽  
Antonella Imperiale ◽  
Claudio Chimenti ◽  
Mario Capogreco ◽  
...  
Keyword(s):  
Bond Strength ◽  
Adhesive System ◽  
Mode Analysis ◽  
Microtensile Bond Strength ◽  
Cavity Preparation ◽  
Etch And Rinse ◽  
Failure Mode Analysis ◽  
Bond Strengths ◽  
Dentin Conditioning

The aim of the present study was to in vitro evaluate the effect of dentin conditioning with hydroabrasion on the microtensile bond strengths of three adhesive systems, compared to the standard etch-and-rinse technique. Sixty extracted human third molars were collected, and their midcoronal occlusal dentin was used for the microtensile bond strength test. Teeth were randomly assigned to three groups according to the adhesive system used: ExciTE F DSC, ENA Bond, and Scotchbond Universal. Specimens from each group were further divided into four subgroups: control specimens were treated with standard adhesive procedures; hydroabraded (HA) specimens were subjected to preventive hydroabrasion with three different intensity levels. After bonding procedures, composite crowns were incrementally built up. After thermocycling, specimens were subsequently sectioned into 1 × 1 mm sticks, and microtensile bond strengths were measured. Data were statistically analyzed. Failure mode analysis was performed. There were no significant differences in terms of bond strength between standard adhesion protocols and adhesion with HA preconditionings. On the other hand, the type of adhesive used had a significant effect on the tensile bond strength. Subgroups treated with hydroabrasion at higher intensity showed a slightly increased frequency of cohesive fractures. In conclusion, hydroabrasion can be used for dentin cavity preparation or finishing, since it does not seem to affect the bonding effectiveness.

scholarly journals Chitosan in different concentrations added to a two-step etch-and-rinse adhesive system: influence on bond strength to dentin

2017 ◽  
Vol 20 (4) ◽  
pp. 55
Author(s):  
Rafael Avellar de Carvalho Nunes ◽  
Flávia Lucisano Botelho do Amaral ◽  
Fabiana Mantovani Gomes França ◽  
Cecilia Pedroso Turssi ◽  
Roberta Tarkany Basting
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Failure Modes ◽  
Resin Composite ◽  
Adhesive System ◽  
Fracture Pattern ◽  
Test Machine ◽  
Microtensile Bond Strength ◽  
Etch And Rinse ◽  
Strength Tests

<p class="Corpo"><strong>Objective</strong>: the aim of the present study was to evaluate the influence of adding different concentrations of chitosan to an experimental two-step etch-and-rinse adhesive system on the bond strength and failure mode to dentin. <strong>Material</strong> <strong>and</strong> <strong>Methods</strong>: thirty-two flat dentin surfaces were obtained from extracted human third molars and divided into four groups  (n=8) for application of the adhesive systems: AD - conventional two-step adhesive system (Adper Single Bond 2); EXP – experimental two-step etch-and-rinse adhesive system; Chi0.2% - EXP with addition of 0.2% Chitosan; Chi0.5% - EXP with addition of 0.5% Chitosan. Resin composite build-ups were made and the composite/dentin specimens were sectioned to obtain rectangular beams with a bond area of approximately 1mm<sup>2</sup>. After 24 hours, the sticks were submitted to microtensile bond strength tests in a universal test machine. The fracture pattern was evaluated under a stereoscopic loupe at 40X magnification. <strong>Results</strong>: one-way analysis of variance showed that the type of adhesive system had no significant effect on the bond strength values (p = 0.142), showing the mean bond strength values (standard deviation), in MPa, for the groups as follows: AD=20.1 (5.4); EXP=16.6 (2.3); Chi0.2%=16.1 (2.8); Chi0.5%=16.9 (2.3). In all the groups there was predominance of cohesive fractures in dentin, representing 68 to 82% of the failure modes. <strong>Conclusion</strong>: the addition of 0.2 or 0.5% of chitosan had no influence on the bond strength and failure mode of an experimental two-step etch-and-rinse adhesive system to dentin.</p><p class="Corpo"><strong>Keywords</strong></p><p class="Corpo">Chitosan; Dental Adhesives; Failure Mode; Microtensile Bond Strength.</p>

scholarly journals Influence of reused dental burs on bond strength to dentin

2014 ◽  
Vol 2 (3) ◽  
pp. 235
Author(s):  
Diogo Pedrollo Lise ◽  
Sylvio Monteiro Júnior ◽  
Renata Gondo
Keyword(s):  
Bond Strength ◽  
Analysis Of Variance ◽  
Adhesive System ◽  
Strength Test ◽  
Microtensile Bond Strength ◽  
Tukey Test ◽  
Diamond Bur ◽  
Human Dentin ◽  
Dental Burs

AIM: this study evaluated the bond strength of an adhesive system to human dentin prepared with reused diamond burs. MATERIAL AND METHODS: five molars (G1) were prepared in a standardized way with five diamond burs. Flat deep dentin surfaces were etched, received adhesive and received composite build-ups. The same burs were cleaned and reused on another five teeth groups (G2 until G8). After 24-hours storage and thermocycling, 50 dentin-resin sticks per group were obtained and subjected to microtensile bond strength test (μTBS). RESULTS: analysis of variance (ANOVA) and Tukey test were applied to identify differences between groups (p<0.05). The reuse of a diamond bur for more than two preparations resulted in significantly lower µTBS values (G1 = G2 > G3 = G4 = G5 = G6 = G7 = G8). CONCLUSION: Reuse of diamond burs interfered on adhesion between dentin and resin.

scholarly journals Influence of Hemostatic Solution on Bond Strength and Physicochemical Properties of Resin Cement

2017 ◽  
Vol 28 (5) ◽  
pp. 624-631
Author(s):  
Isabela Sousa de Araújo ◽  
Célio Jesus do Prado ◽  
Luís Henrique Araújo Raposo ◽  
Carlos José Soares ◽  
Rayssa Ferreira Zanatta ◽  
...  
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Storage Time ◽  
Color Stability ◽  
Degree Of Conversion ◽  
Resin Cement ◽  
Mode Analysis ◽  
Mean Values ◽  
Failure Mode Analysis ◽  
Glass Ceramic Substrate

Abstract The aim of this study was to evaluate the degree of conversion, color stability, chemical composition, and bond strength of a light-cured resin cement contaminated with three different hemostatic solutions. Specimens were prepared for the control (uncontaminated resin cement) and experimental groups (resin cement contaminated with one of the hemostatic solutions) according to the tests. For degree of conversion, DC (n = 5) and color analyses (n = 10), specimens (3 mm in diameter and 2 mm thick) were evaluated by Fourier transform infrared spectroscopy (FTIR) and CIELAB spectrophotometry (L*, a*, b*), respectively. For elemental chemical analysis (n = 1), specimens (2 mm thick and 6 mm in diameter) were evaluated by x-ray energy-dispersive spectroscopy (EDS). The bond strengths of the groups were assessed by the microshear test (n = 20) in a leucite-reinforced glass ceramic substrate, followed by failure mode analysis by scanning electron microscopy (SEM). The mean values, except for the elemental chemical evaluation and failure mode, were evaluated by ANOVA and Tukey’s HSD test. The color stability was influenced by storage time (p<0.001) and interaction between contamination and storage time (p<0.001). Hemostop and Viscostat Clear contamination did not affect the DC, however Viscostat increased the DC. Bond strength of the resin cement to ceramic was negatively affected by the contaminants (p<0.001). Contamination by hemostatic agents affected the bond strength, degree of conversion, and color stability of the light-cured resin cement tested.

scholarly journals Micro versus Macro Shear Bond Strength Testing of Dentin-Composite Interface Using Chisel and Wireloop Loading Techniques

2021 ◽  
Vol 9 (12) ◽  
pp. 140
Author(s):  
Ahmed M. Ismail ◽  
Christoph Bourauel ◽  
Ahmed ElBanna ◽  
Tarek Salah Eldin
Keyword(s):  
Bond Strength ◽  
Failure Mode ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Study Groups ◽  
Mode Analysis ◽  
Specimen Dimension ◽  
Failure Mode Analysis ◽  
Loading Devices ◽  
Systems Failure

Shear bond strength (SBS) testing is a commonly used method for evaluating different dental adhesive systems. Failure mode analysis provides valuable information for better interpretation of bond strength results. The aim of this study was to evaluate the influence of specimen dimension and loading technique on shear bond strength and failure mode results. Eighty macro and micro flowable composite cylindrical specimens of 1.8 and 0.8 mm diameter, respectively, and 1.5 mm length were bonded to dentinal substrate. Four study groups were created (n = 20): Macroshear wireloop, Gp1; Microshear wireloop, Gp2; Macroshear chisel, Gp3; and Microshear chisel, Gp4. They were tested for SBS using chisel and wireloop loading devices followed by failure mode analysis using digital microscopy and SEM. Two- and one-way ANOVA were used to compare stress at failure values of different groups while the Kruskal–Wallis test was used to compare between failure modes of the tested groups. Gp4 recorded the highest mean stress at failure 54.1 ± 14.1 MPa, and the highest percentage of adhesive failure in relation to the other groups. Specimen dimension and loading technique are important parameters influencing the results of shear bond strength. Micro-sized specimens and chisel loading are recommended for shear testing.

scholarly journals Impact of radiotherapy on the bond strength of different adhesive systems to human dentin

2019 ◽  
Vol 18 ◽  
pp. e191638
Author(s):  
Renally Bezerra Wanderley Lima ◽  
Maria Luiza Pontual ◽  
Venâncio Fernandes Dantas ◽  
Sônia Saeger Meireles ◽  
Ana Karina Maciel Andrade ◽  
...  
Keyword(s):  
Bond Strength ◽  
Failure Modes ◽  
Adhesive System ◽  
Adhesive Systems ◽  
Microtensile Bond Strength ◽  
Posterior Teeth ◽  
X Ray ◽  
Etch And Rinse ◽  
Human Dentin

Aim: The aim of this study is to evaluate the effect of radiotherapy on the bond strength of resin-based composite restorations to dentin, performed either 24 h or 1 year before or after radiation. Methods: Ninety-six posterior teeth were randomly distributed into the following groups: IB (n = 16), irradiated teeth were restored 1 year after x-ray application; NB (n = 16), not irradiated teeth were stored for 1 year and then restored. IA (n = 32), teeth were restored and irradiated at 24 h or 1 year after the restoration. NA (n = 32), teeth were restored, not irradiated, and tested as IA. Eight samples from each group were randomly assigned to either the three-step or two-step etch-and rinse adhesive system procedure. The irradiated specimens were subjected to 60 Gy of x-ray radiation fractionally. The restored teeth were vertically sectioned, and 1-mm2 resin–dentin sticks were obtained and submitted to the microtensile bond strength test. The bond strength data were analyzed by two-way analysis of variance (ANOVA) followed by Tukey’s test (p < 0.05). Failure modes were examined by optical microscopy and scanning electron microscopy. Results: The IB group showed lower bond strength values compared to the NB group. The bond strength values between the adhesive systems were not statistically different. Conclusion: The application of radiation dose decreased the bond strength of the adhesive restorations to dentin when the bonding procedure was conducted 1 year after in vitro radiotherapy.

Case Study and Fault Modeling for Wrong Redundancy Evaluation on DRAM Devices

2007 ◽  
Author(s):  
Martin Versen ◽  
Dorina Diaconescu ◽  
Jerome Touzel
Keyword(s):  
Failure Mode ◽  
Failure Modes ◽  
Fault Modeling ◽  
Mode Analysis ◽  
Root Cause ◽  
Failure Mode Analysis

Abstract The characterization of failure modes of DRAM is often straight forward if array related hard failures with specific addresses for localization are concerned. The paper presents a case study of a bitline oriented failure mode connected to a redundancy evaluation in the DRAM periphery. The failure mode analysis and fault modeling focus both on the root-cause and on the test aspects of the problem.

Sign in / Sign up

Export Citation Format

Share Document