scholarly journals Research on Distribution of Flow Field and Simulation of Working Pulsation Based on Rotating-Sleeve Distributing-Flow System

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Yanjun Zhang ◽  
Hongxin Zhang ◽  
Jingzhou Yang ◽  
Qinghai Zhao ◽  
Xiaotian Jiang ◽  
...  
Keyword(s):  
Flow Field ◽  
Normal Condition ◽  
Flow System ◽  
Saturated Vapor ◽  
Flow Area ◽  
Sliding Mesh ◽  
Pump Chamber ◽  
Bottom Dead Center ◽  
Nominal Pressure ◽  
Computational Fluid Dynamics Cfd

To solve problems of leakage, vibration, and noise caused by disorders of flow field distribution and working pulsation in the rotating-sleeve distributing-flow system, governing equations of plunger and rotating sleeve and computational fluid dynamics (CFD) model are developed through sliding mesh and dynamic mesh technology to simulate flow field and working pulsation. Simulation results show that the following issues exist: obviously periodic fluctuation and sharp corner in flow pulsation, backward flow when fluid is transformed between discharge and suction, and serious turbulence and large loss in kinetic energy around the damping groove in transitional movements. Pressure in the pump chamber rapidly rises to 2.2 MPa involving over 10% more than nominal pressure when the plunger is at the Top Dead Center (TDC) considering changes about damping groove’s position and flow area in two transitional movements. Shortly pressure overshoot gradually decreases to a normal condition with increasing flow area. Similarly, pressure in the pump chamber instantaneously drops to a saturated vapor pressure −98.9 KPa when the plunger is at the Bottom Dead Center (BDC). With increasing flow area the overshoot gradually increases to the normal condition. This research provides foundations for investigating flow field characteristic and structure optimization of rotating-sleeve distributing-flow system.

Numerical Simulation and Vibration Analysis of Inner Flow Field for Lage-Sized Throttle Valve

2012 ◽  
Vol 233 ◽  
pp. 154-157
Author(s):  
Guo Qin Huang ◽  
Ying He ◽  
Jin Yu
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Flow Field ◽  
Vibration Analysis ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Control Valve ◽  
Flow Area ◽  
Throttle Valve ◽  
Computational Fluid Dynamics Cfd

Based on the computational fluid dynamics(CFD) technique, the three-dimensional inner flow field of a large-sized throttle valve was built and the dynamics characteristics of the control valve were analyzed. The results indicate that the main reason for the spool and valve vibration was the cavitations at the spool and the whirlpool flow at the outlet of the valve, and the fluid velocity rises as the decreasing of the flow area at the same opening. The research f indings will provide the theory basis for the later throttle valves development and optimization with littler vibration and higher efficiency.

scholarly journals Simulation of Thermal Effects on the Flow Field in a Pilot-Scale Kiln

2021 ◽  
Author(s):  
I. A. Sofia Larsson ◽  
Anna-Lena Ljung ◽  
B. Daniel Marjavaara
Keyword(s):  
Flow Field ◽  
Coal Combustion ◽  
Thermal Effects ◽  
Iron Ore ◽  
Combustion Process ◽  
Pilot Scale ◽  
Mixing Properties ◽  
Process Gas ◽  
Mixing Rates ◽  
Computational Fluid Dynamics Cfd

AbstractThe flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

scholarly journals Rheological Properties of Wood–Plastic Composites by 3D Numerical Simulations: Different Components

Forests ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 417
Author(s):  
Xingcong Lv ◽  
Xiaolong Hao ◽  
Rongxian Ou ◽  
Tao Liu ◽  
Chuigen Guo ◽  
...  
Keyword(s):  
Flow Field ◽  
Rheological Properties ◽  
Wood Fiber ◽  
Velocity Shear ◽  
Wood Plastic Composites ◽  
Shear Rates ◽  
Plastic Composites ◽  
Power Law Fluids ◽  
Field Information ◽  
Computational Fluid Dynamics Cfd

The rheological properties of wood–plastic composites (WPCs) with different wood fiber contents were investigated using a rotational rheometer under low shear rates. The flow field information was analyzed and simulated by Ansys Polyflow software. The results showed that the WPCs with different wood fiber contents behaved as typical power-law fluids. A higher wood fiber content increased the shear thinning ability and pseudoplasticity of the WPCs. The pressure, velocity, shear rate, and viscosity distributions of the WPC during extrusion could be predicted by computational fluid dynamics (CFD) Ansys Polyflow software to explore the effects of different components on the flow field of WPCs.

scholarly journals Research on Cavitation of the Rotating-Sleeve Distributing Flow System Considering Different Cam Groove Profiles

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2139
Author(s):  
Shanxiao Du ◽  
Jichao Hong ◽  
Hongxin Zhang ◽  
Qinghai Zhao ◽  
Tiezhu Zhang ◽  
...  
Keyword(s):  
Volume Fraction ◽  
Flow System ◽  
Volumetric Efficiency ◽  
Piston Pump ◽  
Operating Frequency ◽  
Cavitation Model ◽  
Pump Chamber ◽  
Orthogonal Experiments ◽  
Simulation Results ◽  
Further Development

Reciprocating piston pumps are widely used in various fields, such as automobiles, ships, aviation, and engineering machinery. Conventional reciprocating piston pump distributing flow (RPPDF) systems have the disadvantages of a loose structure and low volumetric efficiency, as well as affected positively by the operating frequency. In this paper, a novel rotating-sleeve distributing flow (RSDF) system is presented for bridging these drawbacks, as well as structurally improved to overcome the inoperable and challenging problems in oil intake and discharge found in the experiment. Moreover, the Singhal cavitation model specifically for the RSDF system and four-cam groove profiles (CGPs) is established. To find the most suitable CGP to reduce the RSDF’s cavitation, the cavitation of the RSDF system was investigated, combining with simulations by taking into account the gap among the rotating sleeve, the pump chamber, and experiments on four presented CGPs. Simulation results based on vapor volume fraction, cavitation ratio, and volumetric efficiency show that the linear profile’s cavitation is the weakest. Finally, the correctness of the simulation is verified through orthogonal experiments. This research is of great significance to the further development of the RSDF system; more important, it has great potential to promote the reform of the RPPDF method.

Construction Ventilation Scheme Optimization of Underground Main Powerhouse Based on CFD

2013 ◽  
Vol 368-370 ◽  
pp. 619-623
Author(s):  
Zhen Liu ◽  
Xiao Ling Wang ◽  
Ai Li Zhang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Air Flow ◽  
Scheme Optimization ◽  
Pressure Distributions ◽  
Air Volume ◽  
Computational Fluid Dynamics Cfd ◽  
Traditional Construction ◽  
Ventilation Scheme

For the purpose of avoiding the deficiency of the traditional construction ventilation, the ventilation of the underground main powerhouse is simulated by the computational fluid dynamics (CFD) to optimize ventilation parameters. A 3D unsteady RNG k-ε model is performed for construction ventilation in the underground main powerhouse. The air-flow field and CO diffusion in the main powerhouse are simulated and analyzed. The two construction ventilation schemes are modelled for the main powerhouse. The optimized ventilation scheme is obtained by comparing the air volume and pressure distributions of the different ventilation schemes.

scholarly journals Effect of Doppler flow meter position on discharge measurement in surcharged manholes

2017 ◽  
Vol 77 (3) ◽  
pp. 647-654 ◽  
Author(s):  
Haoming Yang ◽  
David Z. Zhu ◽  
Yanchen Liu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Flow Regimes ◽  
Flow Meter ◽  
Flow Meters ◽  
Flow Discharge ◽  
Doppler Flow ◽  
Sewer Systems ◽  
Computational Fluid Dynamics Cfd

Abstract Determining the proper installation location of flow meters is important for accurate measurement of discharge in sewer systems. In this study, flow field and flow regimes in two types of manholes under surcharged flow were investigated using a commercial computational fluid dynamics (CFD) code. The error in measuring the flow discharge using a Doppler flow meter (based on the velocity in a Doppler beam) was then estimated. The values of the corrective coefficient were obtained for the Doppler flow meter at different locations under various conditions. Suggestions for selecting installation positions are provided.

Research on CFD Simulation of the Cement Slurry Mixer

2012 ◽  
Vol 621 ◽  
pp. 196-199
Author(s):  
Shui Ping LI ◽  
Ya Li Yuan ◽  
Lu Gang Shi
Keyword(s):  
Flow Field ◽  
High Performance ◽  
Cfd Simulation ◽  
Structural Parameters ◽  
Internal Flow ◽  
Simulation Method ◽  
Cement Slurry ◽  
Fluid Machinery ◽  
Computational Fluid Dynamics Cfd ◽  
Machinery Design

Numerical simulation method of the internal flow field of fluid machinery has become an important technology in the study of fluid machinery design. In order to obtain a high-performance cement slurry mixer, computational fluid dynamics (CFD) techniques are used to simulate the flow field in the mixer, and the simulation results are studied. According to the analysis results, the structural parameters of the mixer are modified. The results show the mixer under the revised parameters meet the design requirements well. So CFD analysis method can shorten design period and provide valuable theoretical guidance for the design of fluid machinery.

CFD Leakage Predictions of Unworn and Worn Labyrinth Seals With and Without Tooth Axial Offset

2017 ◽  
Author(s):  
Hasham H. Chougule ◽  
Alexander Mirzamoghadam
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Steady State ◽  
Flow Field ◽  
Labyrinth Seals ◽  
Small Clearance ◽  
Total Leakage ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Deflection

The objective of this study is to develop a Computational Fluid Dynamics (CFD) based methodology for analyzing and predicting leakage of worn or rub-intended labyrinth seals during operation. The simulations include intended tooth axial offset and numerical modeling of the flow field. The purpose is to predict total leakage through the seal when an axial tooth offset is provided after the intended/unintended rub. Results indicate that as expected, the leakage for the in-line worn land case (i.e. tooth under rub) is higher compared to unworn. Furthermore, the intended rotor/teeth forward axial offset/shift with respect to the rubbed land reduces the seal leakage. The overall leakage of a rubbed seal with axial tooth offset is observed to be considerably reduced, and it can become even less than a small clearance seal designed not to rub. The reduced leakage during steady state is due to a targeted smaller running gap because of tooth offset under the intended/worn land groove shape, higher blockages, higher turbulence and flow deflection as compared to worn seal model without axial tooth offset.

scholarly journals EFFECT OF GALLERIES ON THE WIND FLOW STRUCTURE AND POLLUTANT TRANSPORT WITHIN STREET CANYONS WITH OR WITHOUT FACADE ROUGHNESS ELEMENTS (BALCONIES)

2020 ◽  
Vol 7 (12) ◽  
pp. 45-59
Author(s):  
V. A. Karkoulias ◽  
P. E. Marazioti ◽  
D. P. Georgiou ◽  
E. A. Maraziotis
Keyword(s):  
Flow Field ◽  
Concentration Distribution ◽  
Cfd Simulation ◽  
Field Structure ◽  
Flow Structures ◽  
Street Canyons ◽  
Ansys Fluent ◽  
Roughness Elements ◽  
Computational Fluid Dynamics Cfd ◽  
The Vertical Distribution

This paper investigates how the structure of the flow field and the vertical distribution of the pollutant concentration near the wall facades of street canyons are affected by the presence of some elements such as street level galleries. Numerical results are presented for various gallery geometries in combination with facade roughness elements (balconies) for a canyon of an aspect ratio equal to h/w=2.33. The results were obtained by a Computational Fluid Dynamics (CFD) simulation employing the ANSYS-FLUENT suite that incorporated the k-e turbulent (RNG) model. The simulation generated several flow structures inside the canyon (mainly vortices), whose characteristic properties (e.g. number, strength and size) are discussed in terms of the effect of the galleries on the flow field structure and the roughness generated by the building façade balconies. The results indicate a significant influence on both the flow field structure and the mass concentration distribution of the polluting particles.

Numerical Analysis of the LCS 2 airwake to understand potential interactions during helipcopter operations

2015 ◽  
Author(s):  
Brent S. Paul
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Analysis ◽  
Flow Field ◽  
Ship Design ◽  
It Impacts ◽  
Flight Envelope ◽  
Computational Fluid Dynamics Cfd ◽  
Potential Interactions ◽  
Flight Deck

The successful integration of aviation capabilities aboard ships is a complex endeavor that must balance ship design with the flight envelope of the helicopter. This can be particularly important when considering air wakes and other flow around the superstructure as it impacts the flight deck. This flow can generate unsteady structures that may interfere with safe helicopter operations. Computational fluid dynamics (CFD) is commonly used to characterize the flow field and assess potential impacts to the flight envelope, which can be used to help define an operating envelope for helicopter operations.

Sign in / Sign up

Export Citation Format

Share Document