scholarly journals Bulk Mechanical Properties Testing of Metallic Marginal Glass Formers

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Thien Q. Phan ◽  
James P. Kelly ◽  
Michael E. Kassner ◽  
Veronica Eliasson ◽  
Olivia A. Graeve ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Nominal Composition ◽  
Vickers Indentation ◽  
Minimal Sample ◽  
Plasma Sintering ◽  
Mechanical Properties Testing ◽  
Point Bend

We developed a unique three-point bend testing apparatus to measure bulk mechanical properties of a model metallic glass alloy (SAM2X5 with nominal composition Fe49.7Cr17.1Mn1.9Mo7.4W1.6B15.2C3.8Si2.4) prepared by spark plasma sintering. The relatively large sample sizes in the present work allowed for the preparation of test specimens with a macroscale cross section (in the millimeter range) with well-controlled sample dimensions closer to standardized tests. Wire saw cutting allowed for a relatively sharp notch radius (3x smaller than previous studies) and minimal sample damage. We determined that Young’s modulus and notch fracture toughness measured by our three-point bending apparatus are 230 GPa and 4.9 MPa·m1/2. Also, Vickers indentation and flexure testing provided consistent results for Young’s modulus. Indentation fracture toughness measured by Vickers indentation produced values at least 50% lower than by flexure. The microscale mechanical properties testing technique presented in this work and subsequent analyses are applicable to specimens of other compositions or ones prepared by other methods.

Densification, Microstructure, and Behavior of Hydroxyapatite Ceramics Sintered by Using Spark Plasma Sintering

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Shufeng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Young’S Modulus ◽  
Spark Plasma Sintering ◽  
Young's Modulus ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature And Pressure

This paper discusses the dependence of the mechanical properties and microstructure of sintered hydroxyapatite (HA) on the sintering temperature and pressure. A set of specimens was prepared from as-received HA powder and sintered by using a spark plasma sintering (SPS) process. The sintering pressures were set at 22.3MPa, 44.6MPa, and 66.9MPa, and sintering was performed in the temperature range from 800°Cto1000°C at each pressure. Mechanisms underlying the interrelated temperature-mechanical and pressure-mechanical properties of dense HA were investigated. The effects of temperature and pressure on the flexural strength, Young’s modulus, fracture toughness, relative density, activation energy, phase stability, and microstructure were assessed. The relative density and grain size increased with an increase in the temperature. The flexural strength and Young’s modulus increased with an increase in the temperature, giving maximum values of 131.5MPa and 75.6GPa, respectively, at a critical temperature of 950°C and 44.6MPa, and the fracture toughness was 1.4MPam1∕2 at 1000°C at 44.6MPa. Increasing the sintering pressure led to acceleration of the densification of HA.

Fabrication of Titanium / Biodegradable-Polymer FGM for Medical Application

2009 ◽  
Vol 631-632 ◽  
pp. 199-204 ◽  
Author(s):  
Yoshimi Watanabe ◽  
Yoshimi Iwasa ◽  
Hisashi Sato ◽  
Akira Teramoto ◽  
Koji Abe
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Medical Application ◽  
Hot Water ◽  
Porous Ti ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Biodegradable Poly ◽  
Spark Plasma

Ti and Ti alloys are widely used as metallic implants, because of their good mechanical properties and nontoxic behavior. However, they have problems as the implant-materials, namely, high Young’s modulus comparing that of bone and low bonding ability with bone. There is a need to develop the Ti and Ti alloys with lower Young’s modulus and good bonding ability. In previous study, Ti composite containing biodegradable poly-L-lactic-acid (PLLA) fiber has been fabricated to improve these problems. However, this composite has low strength because of the imperfect sintering of Ti matrix. To improve its strength, sintering of Ti matrix should be completed. In this study, Ti-NaCl composite material was fabricated by spark plasma sintering (SPS) method using powder mixture of Ti and NaCl to complete the sintering of Ti matrix. To obtain porous Ti samples, Ti-NaCl composite were put into hot water of 100 oC. The porous Ti was dipped into PLLA melt in order to introduce PLLA into the pores of porous Ti. Finally, Ti-PLLA composite was obtained, and PLLA plays a role as reinforcement of Ti matrix. It was found that the Ti-PLLA composite has gradient structure and mechanical properties.

scholarly journals Effects of CNT Addition on Mechanical Properties, Electric Conductivity and Oxidation Resistance of Al2O3-TiC Composite

2013 ◽  
Vol 761 ◽  
pp. 83-86
Author(s):  
Hideaki Sano ◽  
Junichi Morisaki ◽  
Guo Bin Zheng ◽  
Yasuo Uchiyama
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Electric Conductivity ◽  
Young’S Modulus ◽  
Oxidation Resistance ◽  
Young's Modulus ◽  
Tic Particle

Effects of carbon nanotubes (CNT) addition on mechanical properties, electric conductivity and oxidation resistance of CNT/Al2O3-TiC composite were investigated. It was found that flexural strength, Young’s modulus and fracture toughness of the composites were improved by addition of more than 2 vol%-CNT. In the composites with more than 3 vol%-CNT, the oxidation resistance of the composite was degraded. In comparison with Al2O3-26vol%TiC sample as TiC particle-percolated sample, the Al2O3-12vol%TiC-3vol%CNT sample, which is not TiC particle-percolated sample, shows almost the same mechanical properties and electric conductivity, and also shows thinner oxidized region after oxidation at 1200°C due to less TiC in the composite.

scholarly journals Formation and Properties of the Ta-Y2O3, Ta-ZrO2, and Ta-TaC Nanocomposites

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
J. Jakubowicz ◽  
M. Sopata ◽  
G. Adamek ◽  
P. Siwak ◽  
T. Kachlicki
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Composites ◽  
Ceramic Phase ◽  
Plasma Sintering ◽  
Average Grain Size ◽  
Bulk Nanocrystalline

The nanocrystalline tantalum-ceramic composites were made using mechanical alloying followed by pulse plasma sintering (PPS). The tantalum acts as a matrix, to which the ceramic reinforced phase in the concentration of 5, 10, 20, and 40 wt.% was introduced. Oxides (Y2O3 and ZrO2) and carbides (TaC) were used as the ceramic phase. The mechanical alloying results in the formation of nanocrystalline grains. The subsequent hot pressing in the mode of PPS results in the consolidation of powders and formation of bulk nanocomposites. All the bulk composites have the average grain size from 40 nm to 100 nm, whereas, for comparison, the bulk nanocrystalline pure tantalum has the average grain size of approximately 170 nm. The ceramic phase refines the grain size in the Ta nanocomposites. The mechanical properties were studied using the nanoindentation tests. The nanocomposites exhibit uniform load-displacement curves indicating good integrity and homogeneity of the samples. Out of the investigated components, the Ta-10 wt.% TaC one has the highest hardness and a very high Young’s modulus (1398 HV and 336 GPa, resp.). For the Ta-oxide composites, Ta-20 wt.% Y2O3 has the highest mechanical properties (1165 HV hardness and 231 GPa Young’s modulus).

Mechanical Properties of Transparent Polycrystalline Silicon Nitride

2006 ◽  
Vol 317-318 ◽  
pp. 305-308 ◽  
Author(s):  
Rak Joo Sung ◽  
Takafumi Kusunose ◽  
Tadachika Nakayama ◽  
Yoon Ho Kim ◽  
Tohru Sekino ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
Young’S Modulus ◽  
Fracture Strength ◽  
Polycrystalline Silicon ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Β Phase ◽  
Α Phase

A novel transparent polycrystalline silicon nitride was fabricated by hot-press sintering with MgO and AlN as additives. The mixed powder with 3 wt.% MgO and 9 wt.% AlN was sintered at 1900oC for 1 hour under 30 MPa pressure in a nitrogen gas atmosphere. Transparent polycrystalline silicon nitride was successfully fabricated. The mechanical properties such as density, hardness, young’s modulus, fracture strength and fracture toughness were evaluated. The effect of α/β phase on the mechanical properties of transparent polycrystalline silicon nitride was investigated. The properties were changed depending on the amount of α/β phase. The hardness and Young's modulus increased with increasing the volume fraction of α-phase fraction as a reflection of the higher hardness of α-phase Si3N4. The fracture toughness and fracture strength decreased with decreasing the volume fraction of β-phase Si3N4.

Densification Behaviour and Mechanical Properties on MgO Doped Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 3-10
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Total Hip Arthroplasty ◽  
Young’S Modulus ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Two Stage ◽  
Positive Effect ◽  
Zirconia Toughened Alumina

The effect of doping small amounts of Magnesium Oxide ranging between 0 to 1 vol% on Zirconia Toughened Alumina (ZTA) composites which is one of main biomaterial used for production of total hip arthroplasty were investigated. The samples were produced via conventional two-stage sintering with T1 varies between 1450°C and 1550°C with heating rate of 20°C/min. The samples were then rapid cooled to T2 set at 1400°C with holding time of 12 hours. The microstructural and mechanical properties of the two-stage sintered ZTA are then investigated to determine the feasibility of MgO addition. Combination of two-stage sintering at T1 above 1500 and also small amount of MgO up to 0.5 vol% were shown to have positive effect on ZTA which exhibited improvement on its grain size, mechanical properties such as Vickers hardness, Young’s modulus and fracture toughness compared to undoped ZTA composites. The sample with 0.5 vol% MgO addition sintered at T1 of 1500°C and T2 1400°C was able to achieve Vickers hardness of 19.6 GPa, Young’s modulus of 408 GPa and fracture toughness of 6.8 MPam1/2 without significant grain growth compared to undoped ZTA composites.

scholarly journals Investigation of Nano-Mechanical and- Tribological Properties of Hydrogenated Diamond Like Carbon (DLC) Coatings

2016 ◽  
Vol 33 (6) ◽  
pp. 769-776 ◽  
Author(s):  
Y.-R. Jeng ◽  
S. Islam ◽  
K-T. Wu ◽  
A. Erdemir ◽  
O. Eryilmaz
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Friction Coefficient ◽  
Young’S Modulus ◽  
Tribological Properties ◽  
Young's Modulus ◽  
Chemical Vapour ◽  
Diamond Like Carbon ◽  
Dlc Coatings ◽  
Mechanical And Tribological Properties

AbstractHydrogenated diamond like Carbon (H-DLC) is a promising lubricious coating that attracted a great deal of interest in recent years mainly because of its outstanding tribological properties. In this study, the nano-mechanical and -tribological properties of a range of H-DLC films were investigated. Specifically, four kinds of H-DLC coatings were produced on Si substrates in pure acetylene, pure methane, 25% methane + 75% hydrogen, 50% methane + 50% hydrogen discharge plasmas using a plasma enhanced chemical vapour deposition (PECVD) system. Nano indentation was performed to measure the mechanical properties such as hardness and young's modulus and nanoscartching was performed to investigate the frictional behavior and wear mechanism of the H-DLC samples in open air. Moreover, Vickers indentation method was utilized to assess the fracture toughness of the samples. The results revealed that there is a strong correlation between the mechanical properties (hardness, young's modulus, fracture toughness) and the friction coefficient of DLC coatings and the source gas chemistry. Lower hydrogen to carbon ratio in source gas leads to higher hardness, young's modulus, fracture toughness and lower friction coefficient. Furthermore, lower wear volume of the coated materials was observed when the friction coefficient was lower. It was also confirmed that lower hydrogen content of the DLC coating leads to higher wear resistance under nanoscratch conditions.

Effect of Temperature and Holding Time on Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 11-18
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Young’S Modulus ◽  
Sintering Temperature ◽  
Young's Modulus ◽  
Holding Time ◽  
Effect Of Temperature ◽  
Two Stage ◽  
Pinning Effect ◽  
Zirconia Toughened Alumina

The microstructure and mechanical properties of Zirconia Toughened Alumina (ZTA) produced via two-stage sintering at various sintering temperature of T1 and T2 in addition to effect of various holding time were investigated. T1 temperature was set between the range of 1400°C to 1500°C with a heating rate of 20°C/min. The samples were then sintered at T2 ranging from 1350°C to 1400°C followed by various holding time between 2 hours to 12 hours. The sintered samples’ microstructural properties, bulk density, hardness (Vickers hardness), elastic modulus (Young’s modulus) and fracture toughness (K1C) were then determined. Compared to standard holding time of two-stage sintering which is 12 hours, results show that ZTA produced via two-stage sintering with shorter holding time of 4 hours with T1 set at 1500°C and T2 of 1450°C are capable of achieving full densification. In addition, the same sample were also able to achieve hardness up to 19 GPa, Young’s modulus of 390 GPa and fracture toughness of 6.1 MPam1/2. The improvement in mechanical properties can be mainly attributed to the absent of surface diffusion at T2 above 1400°C and also presence of Y-TZP which contributed to lower grain growth due to the pinning effect.

Mechanical integrity of yttria-stabilised zirconia doped with Np oxide

2006 ◽  
Vol 932 ◽  
Author(s):  
Hajime Kinoshita ◽  
Ken-ichi Kuramoto ◽  
Masayoshi Uno ◽  
Shinsuke Yamanaka ◽  
Hisayoshi Mitamura ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Young’S Modulus ◽  
Elastic Deformation ◽  
Borosilicate Glass ◽  
Young's Modulus ◽  
Crack Development ◽  
Waste Form ◽  
Mechanical Integrity ◽  
Waste Forms

ABSTRACTMechanical properties of YSZ doped with Np oxide were studied to investigate the sufficiency to be a waste form for immobilisation of highly concentrated TRU. The study was conducted focusing on Vickers (HV) and Knoop (HK) hardness, Young's modulus (E) and fracture toughness (KIC). The results showed that YSZ is harder and more resistant to elastic deformation and crack development than such waste forms as borosilicate glass and synroc. The effects of porosity and Np content on HV, HK, E and KIC are also discussed.

Sign in / Sign up

Export Citation Format

Share Document