scholarly journals High Current Density Chronopotentiometric Electrosynthesis and SEM Characterization of Hexanethiol-Monolayer-Protected Silver Planar Nanotriangles (Ag@C6SH)

2016 ◽  
Vol 2016 ◽  
pp. 1-12
Author(s):  
DJafar Vatan Khah Dowlat Sara ◽  
Ahmad Rouhollahi ◽  
Seied Mahdi Pourmortazavi ◽  
Mojtaba Shamsipur
Keyword(s):  
Current Density ◽  
High Current Density ◽  
Average Particle Size ◽  
Average Particle ◽  
Nonaqueous Media ◽  
Experimental Conditions ◽  
Vis Spectroscopy ◽  
Optimized Conditions ◽  
First Time

This work reports for the first time electrosynthesis of hexanethiol capped silver nanotriangles cores (Ag@C6SH NCs) by a rapid, clean, and simple Double Pulse Chronopotentiometric (DCP) method in nonaqueous media, using a Taguchi orthogonal arrayL8design to identify the optimized experimental conditions. It was found that the size and shape of the product could be tuned by the current density, electrolysis time, electrode distance, and amount of NaBH4% used. The Ag@C6SH NCs in different shapes and sizes (in the range of 30 to 44 nm as an average estimation) were synthesized, under different experimental conditions. Finally, the as-prepared nanoclusters electrosynthesized at optimized conditions were characterized by SEM, XRD, and UV-Vis spectroscopy. The average particle size of the triangular/pyramidal shape (Ag@C6SH NCs), obtained under optimized experimental conditions, was30.5±2.0 nm but the majority of nanoparticles in TC3SEM are so much finer.

The Aggregation Study and Characterization of Silver Nanoparticles

2017 ◽  
Vol 263 ◽  
pp. 165-169
Author(s):  
Silvia Chowdhury ◽  
Faridah Yusof ◽  
Nadzril Sulaiman ◽  
Mohammad Omer Faruck
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Silver Nanoparticles ◽  
Absorption Spectrum ◽  
Average Particle Size ◽  
Average Particle ◽  
Transmission Electron ◽  
Vis Spectroscopy

In this article, we have studied the process of silver nanoparticles (AgNPs) aggregation and to stop aggregation 0.3% Polyvinylpyrrolidone (PVP) was used. Aggregation study carried out via UV-vis spectroscopy and it is reported that the absorption spectrum of spherical silver nanoparticles were found a maximum peak at 420 nm wavelength. Furthermore, Transmission Electron Microscopy (TEM) were used to characterized the size and shape of AgNPs, where the average particle size is around 10 to 25 nm in diameter and the AgNPs shape is spherical. Next, Dynamic Light Scattering (DLS) were used, owing to observed size distribution and self-correlation of AgNPs.

scholarly journals Sargassum Influx on the Mexican Coast: A Source for Synthesizing Silver Nanoparticles with Catalytic and Antibacterial Properties

2021 ◽  
Vol 11 (10) ◽  
pp. 4638
Author(s):  
Jose Luis López-Miranda ◽  
Rodrigo Esparza ◽  
Marlen Alexis González-Reyna ◽  
Beatriz Liliana España-Sánchez ◽  
Angel Ramon Hernandez-Martinez ◽  
...  
Keyword(s):  
Particle Size ◽  
Silver Nanoparticles ◽  
Average Particle Size ◽  
Antibacterial Properties ◽  
Average Particle ◽  
X Ray Diffraction ◽  
X Ray ◽  
Experimental Parameters ◽  
First Time

This work reports, for the first time, the synthesis of silver nanoparticles using extracts of the species of Sargassum natans and Sargassum fluitans (AgNPs-S). Their antibacterial and catalytic properties are compared with silver nanoparticles obtained by chemical synthesis (AgNPs-C). The characterization of AgNPs-S and AgNPs-C was carried out using ultraviolet–visible spectroscopy (UV–Vis), dynamic light scattering (DLS), zeta potential, a scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis. The synthesis of silver nanoparticles using Sargassum extract was optimized through varying experimental parameters, such as the type of solvent used to prepare the extract, the volume of the extract, and the pH of the system. The most efficient sample (AgNPs-S) was prepared with a water–ethanol-based extract, using a 3:1 volumetric ratio of extract: a precursor salt with the addition of 1 mL of NaOH pH = 14. The AgNPs-C were spherical in shape, with an average particle size of 11.55 nm, while the AgNPs-S were polyhedral shaped, with an average particle size of 26.39 nm. The synthesized AgNPs-S were found to have significantly higher catalytic activity for the degradation of methylene blue and more effective antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa than AgNPs-C.

scholarly journals Structure and microstructure behavior of iron doped potassium sodium niobate powders

2022 ◽  
Vol 2153 (1) ◽  
pp. 012009
Author(s):  
S Amaya-Zabala ◽  
A Echavarría-Isaza ◽  
J Tobon ◽  
R Roca ◽  
F A Londoño-Badillo
Keyword(s):  
Average Particle Size ◽  
Average Particle ◽  
Sodium Niobate ◽  
Potassium Sodium Niobate ◽  
Homogeneous Microstructure ◽  
Cylindrical Structures ◽  
Potassium Sodium ◽  
First Time ◽  
Structure And Microstructure

Abstract In this paper, the synthesis and characterization of the potassium sodium niobate doped with iron powders have been studied. Solid-state oxide reaction sintering was used. The powders produced in this work exhibit no homogeneous microstructure, which introduced the growth of random cylindrical structures and will can contribute to the increased porosity ceramics. It was observed average particle size of 3μm, besides, also it was observed the formation of agglomerations and an increase in the size of these clusters with the increase in the amount of iron. The calcination temperature was 950 °C. This is slightly higher than other potassium sodium niobate powders systems. In addition to the physical and microstructural properties, structural properties are presented and analyzed for the first-time using Mössbauer spectroscopy as complementary technique in Fe 3+doped potassium sodium niobate powders. This work is important to state solid physics because establishes the influence of iron in the potassium sodium niobate system, and so the future obtaining of multifunctional materials that have piezoelectric and magnetic properties.

scholarly journals Lamellar Polypyrene Based on Attapulgite–Sulfur Composite for Lithium–Sulfur Battery

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 483
Author(s):  
Jing Wang ◽  
Riwei Xu ◽  
Chengzhong Wang ◽  
Jinping Xiong
Keyword(s):  
Cathode Material ◽  
Current Density ◽  
High Current Density ◽  
Specific Capacity ◽  
Lithium Sulfur Batteries ◽  
Rate Test ◽  
Sulfur Battery ◽  
Lower Capacity ◽  
Lithium Sulfur

We report on the preparation and characterization of a novel lamellar polypyrrole using an attapulgite–sulfur composite as a hard template. Pretreated attapulgite was utilized as the carrier of elemental sulfur and the attapulgite–sulfur–polypyrrole (AT @400 °C–S–PPy) composite with 50 wt.% sulfur was obtained. The structure and morphology of the composite were characterized with infrared spectroscopy (IR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). An AT @400 °C–S–PPy composite was further utilized as the cathode material for lithium–sulfur batteries. The first discharge specific capacity of this kind of battery reached 1175 mAh/g at a 0.1 C current rate and remained at 518 mAh/g after 100 cycles with capacity retention close to 44%. In the rate test, compared with the polypyrrole–sulfur (PPy–S) cathode material, the AT @400 °C–S–PPy cathode material showed lower capacity at a high current density, but it showed higher capacity when the current came back to a low current density, which was attributed to the “recycling” of pores and channels of attapulgite. Therefore, the lamellar composite with special pore structure has great value in improving the performance of lithium–sulfur batteries.

scholarly journals Nanocrystalline TiO2Electrodes Exhibiting High Storage Capacity and Stability in Rechargeable Lithium Batteries

1995 ◽  
Vol 18 (1) ◽  
pp. 23-30 ◽  
Author(s):  
Sui-Yang Huang ◽  
Ladislav Kavan ◽  
Andreas Kay ◽  
Michael Grätzel ◽  
Ivan Exnar
Keyword(s):  
Current Density ◽  
High Current Density ◽  
Discharge Voltage ◽  
Unit Weight ◽  
Nanocrystalline Films ◽  
Rechargeable Lithium Batteries ◽  
Capacity Loss ◽  
High Storage Capacity ◽  
First Time ◽  
A Current

Nanocrystalline TiO2films were explored for the first time as electrode material for a rechargeable lithium intercalation cell, i.e., Li/LiCF3SO3+ PC/TiO2. Two kinds of nanocrystalline films, TiO2F387 (Degussa) and TiO2colloid-240, were investigated. These films exhibited excellent performance renderings them a promising choice for secondary battery applications. At a current density of 0.01 mA/cm2, two voltage plateaus at 1.78 and 1.89 V were observed for TiO2F387 films during charge and discharge, respectively. The TiO2electrode charge capacity per unit weight rose with decreasing current density. The highest capacity, obtained at a current density of 0.005 mA/cm2and a final discharge voltage of 1.4 V, was 265 mAh/g corresponding to a lithium insertion ratio ofx= 0.8. Nanocrystalline TiO2colloid-240 films showed a similar performance. The cycle life of a TiO2colloid-240 cell at a high current density was found to be excellent; a capacity loss lower than 14% has been observed over 100 charge/discharge cycles.

Synthesis and Characterization of Water-Soluble Monolayer-Protected Gold Nanoparticles

2011 ◽  
Vol 415-417 ◽  
pp. 617-620 ◽  
Author(s):  
Yan Su ◽  
Ying Yun Lin ◽  
Yu Li Fu ◽  
Fan Qian ◽  
Xiu Pei Yang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Gold Nanoparticles ◽  
Average Particle Size ◽  
Water Soluble ◽  
Synthesis And Characterization ◽  
Average Particle ◽  
Transmission Electron

Water-soluble gold nanoparticles (AuNPs) were prepared using 2-mercapto-4-methyl-5- thiazoleacetic acid (MMTA) as a stabilizing agent and sodium borohydride (NaBH4) as a reducing agent. The AuNPs product was analyzed by transmission electron microscopy (TEM), UV-vis absorption spectroscopy and Fourier transform infrared spectroscopy (FTIR). The TEM image shows that the particles were well-dispersed and their average particle size is about 5 nm. The UV-vis absorption and FTIR spectra confirm that the MMTA-AuNPs was stabilized by the carboxylate ions present on the surface of the AuNPs.

scholarly journals Preparation and characterization of domperidone nanoparticles for dissolution improvement

2018 ◽  
Vol 27 (1) ◽  
pp. 39-52
Author(s):  
Mohammed Sabar Al-lami ◽  
Malath H. Oudah ◽  
Firas A. Rahi
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
In Vitro Release ◽  
Methyl Cellulose ◽  
Precipitation Method ◽  
Average Particle ◽  
Antisolvent Precipitation ◽  
Stirring Time

This study was carried out to prepare and characterize domperidone nanoparticles to enhance solubility and the release rate. Domperidone is practically insoluble in water and has low and an erratic bioavailability range from 13%-17%. The domperidone nanoparticles were prepared by solvent/antisolvent precipitation method at different polymer:drug ratios of 1:1 and 2:1 using different polymers and grades of poly vinyl pyrolidone, hydroxy propyl methyl cellulose and sodium carboxymethyl cellulose as stabilizers. The effect of polymer type, ratio of polymer:drug, solvent:antisolvent ratio, stirring rate and stirring time on the particle size, were investigated and found to have a significant (p? 0.05) effect on particle size. The best formula was obtained with lowest average particle size of 84.05. This formula was studied for compatibility by FTIR and DSC, surface morphology by FESEM and crystalline state by XRPD. Then domperidone nanoparticles were formulated into a simple capsule dosage form in order to study of the in vitro release of drug from nanoparticles in comparison raw drug and mixture of polymer:drug ratios of 2:1. The release of domperidone from best formula was highly improved with a significant (p? 0.05) increase.

Fe3O4 Magnetic Preparation by Bauxite Ore Washing Fine Mud

2014 ◽  
Vol 1010-1012 ◽  
pp. 961-965
Author(s):  
Jian Qiang Xiao ◽  
Guo Wei He ◽  
Yan Jin Hu
Keyword(s):  
Particle Size ◽  
Aging Time ◽  
Average Particle Size ◽  
Xrd Analysis ◽  
Test Methods ◽  
Raw Material ◽  
Molar Ratio ◽  
Average Particle ◽  
Experimental Conditions ◽  
Particle Size Analyzer

Bauxite waste sludge as a raw material, the use of reverse chemical coprecipitation synthesize Fe3O4. Researching temperature, precipitation concentration, aging time and Fe2+/Fe3+ molar ratio effect on the particle size, morphology. Optimal experimental conditions: temperature 70 °C, the precipitant NaOH mass ratio of 10%, aging time 3h, Fe2+/Fe3+ molar ratio of 2:3. Test methods using a laser particle size analyzer, XRD analysis of the products were characterized, the product is Fe3O4, the average particle size of 0.11mm.

Sign in / Sign up

Export Citation Format

Share Document