scholarly journals Aeroelastic Analysis of Wings in the Transonic Regime: Planform’s Influence on the Dynamic Instability

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Mario Rosario Chiarelli ◽  
Salvatore Bonomo
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Transonic Flow ◽  
Dynamic Instability ◽  
Swept Wing ◽  
Instability Condition ◽  
Structure Interaction ◽  
Structural Layout ◽  
Aeroelastic Analysis ◽  
Lifting System

This paper presents a study of transonic wings whose planform shape is curved. Using fluid structure interaction analyses, the dynamic instability conditions were investigated by including the effects of the transonic flow field around oscillating wings. To compare the dynamic aeroelastic characteristics of the curved wing configuration, numerical analyses were carried out on a conventional swept wing and on a curved planform wing. The results confirm that, for a curved planform wing, the dynamic instability condition occurs at higher flight speed if compared to a traditional swept wing with similar profiles, aspect ratio, angle of sweep at root, similar structural layout, and similar mass. A curved wing lifting system could thus improve the performances of future aircrafts.

scholarly journals Numerical Investigation into Flutter and Flutter-Buffet Phenomena for a Swept Wing and a Curved Planform Wing

2019 ◽  
Vol 2019 ◽  
pp. 1-19 ◽  
Author(s):  
Mario Rosario Chiarelli ◽  
Salvatore Bonomo
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
High Speed ◽  
Sensitivity Study ◽  
Fuel Saving ◽  
Swept Wing ◽  
Instability Condition ◽  
Aspect Ratios ◽  
Numerical Studies ◽  
Classical Flutter

The results of numerical studies carried out on high-aspect-ratio wings with different planforms are discussed: the transonic regime is analysed for a swept wing and a curved planform wing. The wings have similar aspect ratios and similar aerodynamic profiles. The analyses were carried out by CFD and FE techniques, and the reliability of the numerical aerodynamic results was proven by a sensitivity study. Analysing the performances of the two wings demonstrated that in transonic flight conditions, a noticeable drag reduction can be obtained by adopting a curved planform wing. In addition, for such a wing, the aeroelastic instability condition, consisting in a classical flutter, is postponed compared to a conventional swept wing, for which a flutter-buffet instability occurs. In a preliminary manner, the study shows that, for a curved planform wing, the high speed buffet is not an issue and at the same time notable fuel saving can be achieved.

Performance Prediction for High Turning Low Aspect Ratio Stator Cascades in the Transonic Regime

1970 ◽  
Vol 92 (4) ◽  
pp. 390-398
Author(s):  
H. F. L. Griepentrog
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Flow Field ◽  
Performance Prediction ◽  
Transonic Flow ◽  
Secondary Flows ◽  
Compressor Stage ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Boundary Layer Interaction

This paper describes a method for the prediction of the transonic flow field in a high solidity, high turning cascade, suitable for use as stator of a shock-in-rotor supersonic compressor stage. Effects of shock boundary layer interaction is taken into account by empirical correlation, valid for blade aspect ratios below unity. Use of partial slots for reduction of the secondary flows is briefly discussed and a correlation on slot efficiency is presented.

Effect of Aspect Ratio on Swept Wing Dynamic Stall

2021 ◽  
Author(s):  
Patrick R. Hammer ◽  
Daniel J. Garmann ◽  
Miguel R. Visbal
Keyword(s):  
Aspect Ratio ◽  
Dynamic Stall ◽  
Swept Wing

Flow Measurements in a Nozzle Guide Vane Passage With a Low Aspect Ratio and Endwall Contouring

2000 ◽  
Author(s):  
Steven W. Burd ◽  
Terrence W. Simon
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Guide Vane ◽  
Flow Measurements ◽  
Vast Number ◽  
Aspect Ratios ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

The vast number of turbine cascade studies in the literature has been performed in straight-endwall, high-aspect-ratio, linear cascades. As a result, there has been little appreciation for the role of, and added complexity imposed by, reduced aspect ratios. There also has been little documentation of endwall profiling at these reduced spans. To examine the role of these factors on cascade hydrodynamics, a large-scale nozzle guide vane simulator was constructed at the Heat Transfer Laboratory of the University of Minnesota. This cascade is comprised of three airfoils between one contoured and one flat endwall. The geometries of the airfoils and endwalls, as well as the experimental conditions in the simulator, are representative of those in commercial operation. Measurements with hot-wire anemometry were taken to characterize the flow approaching the cascade. These measurements show that the flow field in this cascade is highly elliptic and influenced by pressure gradients that are established within the cascade. Exit flow field measurements with triple-sensor anemometry and pressure measurements within the cascade indicate that the acceleration imposed by endwall contouring and airfoil turning is able to suppress the size and strength of key secondary flow features. In addition, the flow field near the contoured endwall differs significantly from that adjacent to the straight endwall.

The Effect of a Downstream Rotor on the Measured Performance of a Transonic Turbine Nozzle

1986 ◽  
Vol 108 (2) ◽  
pp. 269-274
Author(s):  
R. G. Williamson ◽  
S. H. Moustapha ◽  
J. P. Huot
Keyword(s):  
Performance Evaluation ◽  
Aspect Ratio ◽  
Flow Field ◽  
Large Scale ◽  
Outer Wall ◽  
Nozzle Flow ◽  
Turning Angle ◽  
Low Aspect Ratio ◽  
Transonic Turbine ◽  
Mach Numbers

Two nozzle designs, involving the same low aspect ratio, high turning angle vanes, and differing in outer wall contour, were tested over a range of exit Mach numbers up to supersonic values. The experiments were conducted on a large-scale, full annular configuration with and without a representative rotor downstream. Nozzle performance was found to be significantly affected by rotor operation, the influence depending on the detailed characteristics of the nozzle flow field, as well as on the design and operation of the rotor itself. It is suggested that performance evaluation of low aspect ratio nozzles of high turning angle may require appropriate testing with a rotor.

Numerical Study of Winglet at Low Reynolds Numbers

2013 ◽  
Author(s):  
Sina Pooladsanj ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Vortex Flow ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Flow Zone ◽  
Low Reynolds Numbers ◽  
Structured Grid ◽  
Flow Field Characteristics ◽  
Wing Aspect Ratio

A numerical study has been performed to evaluate the aerodynamics coefficients of a winglet in the range of Reynolds numbers below 30,000. In this study some parameters on winglet design have been considered. The effect of winglet-tip airfoil thickness has been investigated on aerodynamics coefficients. In order to explore this effect, two different airfoils (NACA0002 and NACA0012) were employed at the winglet-tip. The influence of varying the winglet connection angle to the wing on aerodynamics coefficients and flow field characteristics in the vortex flow zone such as; circulation magnitude and vorticity magnitude in the vortex core have been studied. Six connection angles including 20°, 30°, 40°, 50°, 60° and 70° have been studied. Negative values of these angles have also been considered. In addition, the effect of changing wing aspect ratio on aerodynamics coefficients has been investigated. To solve the flow field around the studied geometry a fully structured grid was used which consists of 84 blocks.

Sign in / Sign up

Export Citation Format

Share Document