The Effect of a Downstream Rotor on the Measured Performance of a Transonic Turbine Nozzle

1986 ◽  
Vol 108 (2) ◽  
pp. 269-274
Author(s):  
R. G. Williamson ◽  
S. H. Moustapha ◽  
J. P. Huot
Keyword(s):  
Performance Evaluation ◽  
Aspect Ratio ◽  
Flow Field ◽  
Large Scale ◽  
Outer Wall ◽  
Nozzle Flow ◽  
Turning Angle ◽  
Low Aspect Ratio ◽  
Transonic Turbine ◽  
Mach Numbers

Two nozzle designs, involving the same low aspect ratio, high turning angle vanes, and differing in outer wall contour, were tested over a range of exit Mach numbers up to supersonic values. The experiments were conducted on a large-scale, full annular configuration with and without a representative rotor downstream. Nozzle performance was found to be significantly affected by rotor operation, the influence depending on the detailed characteristics of the nozzle flow field, as well as on the design and operation of the rotor itself. It is suggested that performance evaluation of low aspect ratio nozzles of high turning angle may require appropriate testing with a rotor.

scholarly journals Endwall Heat Transfer Measurements in a Transonic Turbine Cascade

1998 ◽  
Vol 120 (2) ◽  
pp. 305-313 ◽  
Author(s):  
P. W. Giel ◽  
D. R. Thurman ◽  
G. J. Van Fossen ◽  
S. A. Hippensteele ◽  
R. J. Boyle
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Turbine Blade ◽  
Large Scale ◽  
Model Verification ◽  
Quality Data ◽  
Free Stream Turbulence ◽  
Transonic Turbine ◽  
Mach Numbers ◽  
Inlet Conditions

Turbine blade endwall heat transfer measurements are presented for a range of Reynolds and Mach numbers. Data were obtained for Reynolds numbers based on inlet conditions of 0.5 and 1.0 × 106, for isentropic exit Mach numbers of 1.0 and 1.3, and for free-stream turbulence intensities of 0.25 and 7.0 percent. Tests were conducted in a linear cascade at the NASA Lewis Transonic Turbine Blade Cascade Facility. The test article was a turbine rotor with 136 deg of turning and an axial chord of 12.7 cm. The large scale allowed for very detailed measurements of both flow field and surface phenomena. The intent of the work is to provide benchmark quality data for CFD code and model verification. The flow field in the cascade is highly three dimensional as a result of thick boundary layers at the test section inlet. Endwall heat transfer data were obtained using a steady-state liquid crystal technique.

scholarly journals Aerodynamic Performance of a Transonic Low Aspect Ratio Turbine Nozzle

1992 ◽  
Author(s):  
S. H. Moustapha ◽  
W. E. Carscallen ◽  
J. D. McGeachy
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Large Scale ◽  
Three Dimensional ◽  
Surface Flow ◽  
Flow Angle ◽  
Turning Angle ◽  
Flow Solver ◽  
Annular Cascade ◽  
Measured Pressure

This paper presents detailed information on the three-dimensional flow field in a realistic turbine nozzle with an aspect ratio of 0.65 and a turning angle of 76 degrees. The nozzle has been tested in a large scale planar cascade over a range of exit Mach numbers from 0.3 to 1.3. The experimental results are presented in the form of nozzle passage Mach number distributions and spanwise distribution of losses and exit flow angle. Details of the flow field inside the nozzle passage are examined by means of surface flow visualization and Schtieren pictures. The performance of the nozzle is compared to the data obtained for the same nozzle tested in an annular cascade and a stage environment. Excellent agreement is found between the measured pressure distribution and the prediction of a 3D Euler flow solver.

Aerodynamic Performance of a Transonic Low Aspect Ratio Turbine Nozzle

1993 ◽  
Vol 115 (3) ◽  
pp. 400-408 ◽  
Author(s):  
S. H. Moustapha ◽  
W. E. Carscallen ◽  
J. D. McGeachy
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Large Scale ◽  
Three Dimensional ◽  
Surface Flow ◽  
Flow Angle ◽  
Turning Angle ◽  
Flow Solver ◽  
Annular Cascade ◽  
Measured Pressure

This paper presents detailed information on the three-dimensional flow field in a realistic turbine nozzle with an aspect ratio of 0.65 and a turning angle of 76 deg. The nozzle has been tested in a large-scale planar cascade over a range of exit Mach numbers from 0.3 to 1.3. The experimental results are presented in the form of nozzle passage Mach number distributions and spanwise distribution of losses and exit flow angle. Details of the flow field inside the nozzle passage are examined by means of surface flow visualization and Schlieren pictures. The performance of the nozzle is compared to the data obtained for the same nozzle tested in an annular cascade and a stage environment. Excellent agreement is found between the measured pressure distribution and the prediction of a three-dimensional Euler flow solver.

scholarly journals Endwall Heat Transfer Measurements in a Transonic Turbine Cascade

1996 ◽  
Author(s):  
P. W. Giel ◽  
D. R. Thurman ◽  
G. J. Van Fossen ◽  
S. A. Hippensteele ◽  
R. J. Boyle
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Turbine Blade ◽  
Large Scale ◽  
Turbine Rotor ◽  
Model Verification ◽  
Quality Data ◽  
Transonic Turbine ◽  
Mach Numbers ◽  
Inlet Conditions

Turbine blade endwall heat transfer measurements are given for a range of Reynolds and Mach numbers. Data were obtained for Reynolds numbers based on inlet conditions of 0.5 and 1.0 × 106, for isentropic exit Mach numbers of 1.0 and 1.3, and for freestream turbulence intensities of 0.25% and 7.0%. Tests were conducted in a linear cascade at the NASA Lewis Transonic Turbine Blade Cascade Facility. The test article was a turbine rotor with 136° of turning and an axial chord of 12.7 cm. The large scale allowed for very detailed measurements of both flow field and surface phenomena. The intent of the work is to provide benchmark quality data for CFD code and model verification. The flow field in the cascade is highly three-dimensional as a result of thick boundary layers at the test section inlet. Endwall heat transfer data were obtained using a steady-state liquid crystal technique.

Performance Prediction for High Turning Low Aspect Ratio Stator Cascades in the Transonic Regime

1970 ◽  
Vol 92 (4) ◽  
pp. 390-398
Author(s):  
H. F. L. Griepentrog
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Flow Field ◽  
Performance Prediction ◽  
Transonic Flow ◽  
Secondary Flows ◽  
Compressor Stage ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Boundary Layer Interaction

This paper describes a method for the prediction of the transonic flow field in a high solidity, high turning cascade, suitable for use as stator of a shock-in-rotor supersonic compressor stage. Effects of shock boundary layer interaction is taken into account by empirical correlation, valid for blade aspect ratios below unity. Use of partial slots for reduction of the secondary flows is briefly discussed and a correlation on slot efficiency is presented.

Simulation of Three-Dimensional Viscous Flow Within a Multistage Turbine

1990 ◽  
Vol 112 (3) ◽  
pp. 370-376 ◽  
Author(s):  
J. J. Adamczyk ◽  
M. L. Celestina ◽  
T. A. Beach ◽  
M. Barnett
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Three Dimensional ◽  
Equation System ◽  
Aerodynamic Performance ◽  
Experimental Measurements ◽  
Low Aspect Ratio ◽  
Blade Row ◽  
Multistage Turbine ◽  
Secondary Flow Field

This work outlines a procedure for simulating the flow field within multistage turbomachinery, which includes the effects of unsteadiness, compressibility, and viscosity. The associated modeling equations are the average passage equation system, which governs the time-averaged flow field within a typical passage of a blade row embedded within a multistage configuration. The results from a simulation of a low aspect ratio stage and one-half turbine will be presented and compared with experimental measurements. It will be shown that the secondary flow field generated by the rotor causes the aerodynamic performance of the downstream vane to be significantly different from that of an isolated blade row.

Tip Flow Fields in a Low Aspect Ratio Transonic Compressor

1995 ◽  
Author(s):  
P. Russler ◽  
D. Rabe ◽  
B. Cybyk ◽  
C. Hah
Keyword(s):  
Shock Wave ◽  
Aspect Ratio ◽  
Flow Field ◽  
High Frequency ◽  
High Performance ◽  
Flow Structures ◽  
Transonic Compressor ◽  
Low Aspect Ratio ◽  
Laser Data ◽  
Blade Tip

Experimental data and computational predictions are used to characterize the tip flow field of a high performance, low aspect ratio, transonic compressor. Flow structures near the first stage blade tip are monitored experimentally using two different data acquisition schemes. High frequency pressure and laser fringe anemometry data are used to experimentally define the tip flow structure. The high frequency pressure data were acquired with an array of pressure transducers mounted in the rotor casing. Laser data were acquired through a window in the same position. The transducer and laser data adequately define the shock structure at the tip. Both the movement of the shock wave in the blade passage during changes in compressor loading and the interaction between the shock wave and the tip leakage vortex are detected. Similar flow structures and compressor loading effects are numerically predicted using a three-dimensional Navier-Stokes algorithm. A fundamental understanding of the flow field at the blade tip is obtained using these three complementary methods.

Observation of Large-Scale Profile Change of Magnetic Field in a Low-Aspect Ratio Reversed Field Pinch

2008 ◽  
Vol 77 (7) ◽  
pp. 075005 ◽  
Author(s):  
Kensuke Oki ◽  
Ryuya Ikezoe ◽  
Takumi Onchi ◽  
Akio Sanpei ◽  
Haruhiko Himura ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Aspect Ratio ◽  
Large Scale ◽  
Reversed Field Pinch ◽  
Low Aspect Ratio ◽  
Reversed Field ◽  
Scale Profile ◽  
Profile Change

scholarly journals Effect of Partial Shrouds on the Performance and Flow Field of a Low-Aspect-Ratio Axial-Flow Fan Rotor

2011 ◽  
Vol 2011 ◽  
pp. 1-11 ◽  
Author(s):  
N. Sitaram ◽  
G. Ch. V. Sivakumar
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Axial Flow ◽  
Flow Coefficient ◽  
Axial Flow Fan ◽  
Low Velocity ◽  
Flow Measurements ◽  
Low Aspect Ratio ◽  
Partial Shroud ◽  
Velocity Region

The flow field at the rotor exit of a low aspect ratio axial flow fan for different tip geometries and for different flow coefficients is measured in the present study. The following configurations are tested: (1) rotor without partial shroud, designated as rotor (wos), (2) rotor with partial shroud, designated as rotor (ws), and (3) rotor with perforated (perforations in the shape of discrete circular holes) partial shroud, designated as rotor (wps). From steady state measurements, the performance of rotor (wps) is found to be the best. Both the rotors with partial shrouds have stalled at a higher flow coefficient compared to that of rotor (wos). From periodic flow measurements, it is concluded that the low velocity region near the tip section is considerably reduced with the use of partial shrouds with perforations. The extent of this low velocity region for both rotor (wos) and rotor (wps) increases with decreasing flow coefficient due to increased stage loading. This core of low momentum fluid has moved inwards of the annulus and towards the pressure side as the flow coefficient decreases. The extent of the low momentum fluid is smaller for rotor (wps) than that of rotor (wos) at all flow coefficients.

Sign in / Sign up

Export Citation Format

Share Document