scholarly journals Optical Estimation on Pollution Level of Respirable Dust Based on Infrared Transmitting Behavior in Coalmine Fully Mechanized Working Face

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Wen-Zheng Wang ◽  
Yan-Ming Wang ◽  
Guo-Qing Shi
Keyword(s):  
Coal Particle ◽  
Coal Dust ◽  
Operating Conditions ◽  
Dust Concentration ◽  
Optical Channel ◽  
Pollution Level ◽  
Engineering Practice ◽  
Dust Generation ◽  
Working Face ◽  
Comparison Results

Respirable coal particle generated during underground mining is the main cause for gas-dust explosions and coal workers’ pneumoconiosis (CWP) which needs accurate monitoring especially on its concentration. Focusing on the coal dust pollution in the fully mechanized working face of Huangbaici coalmine, coal particle was sampled for further industrial analysis and FT-IR test to obtain its chemical composition and optical constant. Combined with the simulated spatial distribution of airborne dust, the spectral transmission characteristics of coal dust within wavelengths of 2.5 to 25 μm under different operating conditions were obtained. The simulation results show that the transmittance and aerosol optical depth (AOD) of coal dust are closely linked and obviously influenced by the variation of dust generation source (intensity of dust release, position of coal cutting, and the wetting of the coal seam) and airflow field (wind speed and direction of ventilation). Furthermore, an optical channel of 1260–1280 cm−1(7.937–7.813 μm) which is almost only sensitive to the variation of dust concentration but dull to the diameter change of coal dust was selected to establish the correlation of dust concentration and infrared transmittance. The fitting curve was then applied to retrieve the equivalent dust concentration based on optical information, and the comparison results demonstrate that the estimated pollution level is consistent with field measurement data in engineering practice.

scholarly journals A Comparative Study on Fault Detection Methods for Gas Turbine Combustion Systems

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 389
Author(s):  
Jinfu Liu ◽  
Zhenhua Long ◽  
Mingliang Bai ◽  
Linhai Zhu ◽  
Daren Yu
Keyword(s):  
Fault Detection ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Detection Methods ◽  
Distribution Model ◽  
Outlet Temperature ◽  
Combustion System ◽  
Comparison Results ◽  
Gas Turbine Combustion

As one of the core components of gas turbines, the combustion system operates in a high-temperature and high-pressure adverse environment, which makes it extremely prone to faults and catastrophic accidents. Therefore, it is necessary to monitor the combustion system to detect in a timely way whether its performance has deteriorated, to improve the safety and economy of gas turbine operation. However, the combustor outlet temperature is so high that conventional sensors cannot work in such a harsh environment for a long time. In practical application, temperature thermocouples distributed at the turbine outlet are used to monitor the exhaust gas temperature (EGT) to indirectly monitor the performance of the combustion system, but, the EGT is not only affected by faults but also influenced by many interference factors, such as ambient conditions, operating conditions, rotation and mixing of uneven hot gas, performance degradation of compressor, etc., which will reduce the sensitivity and reliability of fault detection. For this reason, many scholars have devoted themselves to the research of combustion system fault detection and proposed many excellent methods. However, few studies have compared these methods. This paper will introduce the main methods of combustion system fault detection and select current mainstream methods for analysis. And a circumferential temperature distribution model of gas turbine is established to simulate the EGT profile when a fault is coupled with interference factors, then use the simulation data to compare the detection results of selected methods. Besides, the comparison results are verified by the actual operation data of a gas turbine. Finally, through comparative research and mechanism analysis, the study points out a more suitable method for gas turbine combustion system fault detection and proposes possible development directions.

scholarly journals Numerical Simulation and Engineering Application of Coalbed Water Injection

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Yijie Shi ◽  
Pengfei Wang ◽  
Ronghua Liu ◽  
Xuanhao Tan ◽  
Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Water Injection ◽  
Engineering Application ◽  
Working Environment ◽  
Engineering Practice ◽  
Characteristic Parameters ◽  
Injection Process ◽  
Working Face ◽  
Dust Reduction

Coalbed water injection is the most basic and effective dust-proof technology in the coal mining face. To understand the influence of coalbed water injection process parameters and coalbed characteristic parameters on coal wetting radius, this paper uses Fluent computational fluid dynamics software to systematically study the seepage process of coalbed water injection under different process parameters and coalbed characteristic parameters, calculation results of which are applied to engineering practice. The results show that the numerical simulation can help to predict the wetness range of coalbed water injection, and the results can provide guidance for the onsite design of coalbed water injection process parameters. The effect of dust reduction applied to onsite coalbed water injection is significant, with the average dust reduction rates during coal cutting and support moving being 67.85% and 46.07%, respectively, which effectively reduces the dust concentration on the working face and improves the working environment.

Computational fluid dynamics optimization of gas drainage technology in gas-mining areas

2021 ◽  
pp. 014459872110635
Author(s):  
Wei Zhao ◽  
Wei Qin
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Coal Seam ◽  
Field Tests ◽  
Mining Area ◽  
Engineering Practice ◽  
Horizontal Distance ◽  
Gas Drainage ◽  
Working Face ◽  
Gas Seepage

Coal mining results in strata movement and surrounding rock failure. Eventually, manual mining space will be occupied by the destructed coal rock, making it difficult to conduct field tests of the coal seam to explore gas seepage and transport patterns. Therefore, computational fluid dynamics (CFD) numerical computation is an important tool for such studies. From the aspect of gas pre-drainage, for layer-through boreholes in the floor roadway of the 8,406 working face in Yangquan Mine 5 in China, reasonable layout parameters were obtained by CFD optimization. For effectively controlling the scope of boreholes along coal seam 9 in the Kaiyuan Mine, CFD computation was performed. The results revealed that the horizontal spacing between boreholes should be ≤2 m when a tri-quincuncial borehole layout is used. Optimization of the surface well position layout for the fault structure zone in the Xinjing Mine of the Yangquan mining area indicated that the horizontal distance between the surface well and the fault plane should be <150 m. From the aspect of gas drainage with mining-induced pressure relief, CFD computation was performed for pressure-relieved gas transport in the K8205 working face of Yangquan Mine 3. The results showed that forced roof caving should be used before the overhang length of hard roof reaches 25 m in the K8205 working face to avoid gas overrun. From the aspect of gas drainage from the abandoned gob, surface well control scopes at different surface well positions were computed, and an O-ring fissure zone is proposed as a reasonable scope for the surface well layout. CFD computation has been widely applied to coal and gas co-extraction in the Yangquan mining area and has played a significant role in guiding related gas drainage engineering practice.

scholarly journals Study on the Fracture Law of Inclined Hard Roof and Surrounding Rock Control of Mining Roadway in Longwall Mining Face

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5344
Author(s):  
Feng Cui ◽  
Shuai Dong ◽  
Xingping Lai ◽  
Jianqiang Chen ◽  
Chong Jia ◽  
...  
Keyword(s):  
Energy Release ◽  
Longwall Mining ◽  
Coal Pillar ◽  
High Energy ◽  
Mechanical Analysis ◽  
Engineering Practice ◽  
Analysis Model ◽  
Hard Roof ◽  
Working Face ◽  
The Stability

In the inclination direction, the fracture law of a longwall face roof is very important for roadway control. Based on the W1123 working face mining of Kuangou coal mine, the roof structure, stress and energy characteristics of W1123 were studied by using mechanical analysis, model testing and engineering practice. The results show that when the width of W1123 is less than 162 m, the roof forms a rock beam structure in the inclined direction, the floor pressure is lower, the energy and frequency of microseismic (MS) events are at a low level, and the stability of the section coal pillar is better. When the width of W1123 increases to 172 m, the roof breaks along the inclined direction, forming a double-hinged structure, the floor pressure is increased, and the frequency and energy of MS events also increases. The roof gathers elastic energy release, and combined with the MS energy release speed it can be considered that the stability of the section coal pillar is better. As the width of W1123 increases to 184 m, the roof in the inclined direction breaks again, forming a multi-hinged stress arch structure, and the floor pressure increases again. MS high-energy events occur frequently, and are not conducive to the stability of the section coal pillar. Finally, through engineering practice we verified the stability of the section coal pillar when the width of W1123 was 172 m, which provides a basis for determining the width of the working face and section coal pillar under similar conditions.

scholarly journals Experimental Research and Numerical Simulation of Ejector Precipitator in a Fully Mechanized Mining Face

2020 ◽  
Vol 45 (11) ◽  
pp. 9815-9833
Author(s):  
Guodong Zhai ◽  
Wentao Zhang ◽  
Yaozong Li ◽  
Xinghao Lu ◽  
Wenyuan Hu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Negative Pressure ◽  
Coal Dust ◽  
Structural Parameters ◽  
Dust Concentration ◽  
Dust Removal ◽  
Measuring Point ◽  
Mining Face ◽  
Supply Water

AbstractIn order to effectively reduce the coal dust concentration in a fully mechanized mining face, this research used laboratory experiment, numerical simulation, and field test to conduct an in-depth exploration of the ejector precipitator installed at the low-level caving coal hydraulic support. Firstly, through the experimental platform in the laboratory, the dust removal effect of the nozzle with different structural parameters was tested, and the 3D particle dynamic analyzer was adopted to verify its atomization characteristics; then, the structural parameters corresponding to the nozzle in the best test results were obtained. Secondly, by using Fluent, the negative pressure flow field in the ejector barrel was numerically simulated. The results indicated that when the pressure of supply water was 12 MPa, the negative pressure value formed in the flow field was the lowest and the inspiratory velocity was the largest, which was conducive to dust removal. Finally, the tests of liquid–gas ratio and dust removal ratio were carried out in a fully mechanized mining face. The results showed that when the nozzle specification recommended by the experiment and the pressure of supply water recommended by the numerical simulation were used, the removal ratios of the total coal dust and the respirable coal dust were 89.5% and 91.0%, respectively, at the measuring point of the highest coal dust concentration. It indicates that the ejector precipitator has a good application effect in reducing the coal dust concentration in a fully mechanized mining face and improving the work environment of coal mine workers.

scholarly journals Screening the Main Factors Affecting the Wear of the Scraper Conveyor Chute Using the Plackett–Burman Method

2019 ◽  
Vol 2019 ◽  
pp. 1-11
Author(s):  
Rui Xia ◽  
Bo Li ◽  
Xuewen Wang ◽  
Zhaojian Yang ◽  
Liping Liu
Keyword(s):  
Particle Size ◽  
Water Content ◽  
Coal Particle ◽  
Normal Load ◽  
Influence Factors ◽  
Optical Microscope ◽  
Operating Conditions ◽  
Wear Loss ◽  
Regression Equations ◽  
Scraper Conveyor

The wear of scraper conveyor chute causes both significant economic and environmental losses by shortening the service life. The life of the chute under coal abrasive wear situations is primarily decided by operating conditions and the materials properties. The comprehensive analysis of the influence factors had not been studied before. In this paper, the Plackett-Burman design (PBD) method was used to screen the main influence factors and a regression equation was developed to predict the wear loss. The steel was tested on a modified pin-on-disk apparatus in which coal abrasive was filled in the disk. The influence factors included water content, gangue content, coal particle size, Hardgrove Grindability-Index (HGI) of the coal, normal load, and scraper chain speed. The results of the investigation suggested that the significance of water content, normal load, and gangue content on wear loss was relatively higher than the HGI of coal, scraper chain speed, and coal particle size. The wear loss increased with the increase of water content, gangue content, normal load, and coal particle size while it decreased as increase in HGI of the coal and scraper chain speed. Based on the significance of the parameters, the regression equations were derived and verified further with a number of test cases. Optical microscope studies revealed the main wear mechanism of the chute was mainly micro-cutting and corrosive wear and accompanied by fatigue fracture.

scholarly journals Optimizing Simulation and Analysis of Automated Top-Coal Drawing Technique in Extra-Thick Coal Seams

Energies ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 232 ◽  
Author(s):  
Qunlei Zhang ◽  
Ruifu Yuan ◽  
Shen Wang ◽  
Dongyin Li ◽  
Huamin Li ◽  
...  
Keyword(s):  
Numerical Models ◽  
Time Estimation ◽  
Engineering Practice ◽  
Coal Seams ◽  
Control Approach ◽  
Working Face ◽  
Geological Conditions ◽  
Round Number ◽  
Element Approach ◽  
Drawing Technique

A particle element approach based on continuum-discontinuum element method (CDEM) is applied to optimize the automated top-coal drawing techniques in extra-thick coal seams. Numerical models with 100 drawing openings are created according to the field engineering geological conditions of Tongxin coal mine in China. An automated coal drawing control approach in numerical modelling based on time criterion is proposed. The rock mixed rate, top-coal recovery rate and the variance of the drawn top coal amount are counted and set as the statistical indicators to evaluate the top-coal drawing techniques. The traditional top-coal drawing criterion, “rocks appear, close the opening”, leads to low recovery of top coal and waste of coal resources in extra-thick coal seams, significantly weakening the transport stability and efficiency of the scraper conveyer. A three-round unequal time top-coal drawing technique is proposed for automated top-coal drawing. Three drawing openings, corresponding to the three top-coal drawing rounds respectively, are working at the same time; in each round, the top-coal drawing sequence is from the first drawing opening at one end of the working face to last drawing opening at another end; the drawing time of each round is not equal and increases with the round number. The numerical inversion approach of iteration steps can be used for real top-coal drawing time estimation and automated drawing process design to achieve a better top coal drawing effect, while the exact time for each drawing round still needs to be corrected by engineering practice.

scholarly journals The Stability of Gob-Side Entry Retaining in a High-Gas-Risk Mine

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Junwen Zhang ◽  
Yulin Li
Keyword(s):  
Coal Mines ◽  
Surrounding Rock ◽  
Shanxi Province ◽  
Engineering Practice ◽  
Efficient Production ◽  
Coal Recovery ◽  
Working Face ◽  
Geological Conditions ◽  
The Stability ◽  
Strengthening Technique

There are series of problems faced by most of the coal mines in China, ranging from low-coal recovery rate and strained replacement of working faces to gas accumulation in the upper corner of coalfaces. Based on the gob-side entry retaining at the No. 18205 working face in a coal mine in Shanxi Province, theoretical analysis, numerical simulation, and engineering practice were comprehensively used to study the mechanical characteristics of the influence of the width of the filling body beside the roadway and the stability of surrounding rock in a high-gas-risk mine. The rational width of the filling body beside the roadway was determined, and a concrete roadway-side support with a headed reinforcement-integrated strengthening technique was proposed, which have been applied in engineering practice. The stability of the filling body beside the roadway is mainly influenced by the movement of the overlying rock strata, and the stability of the surrounding rock can be improved effectively by rationally determining the width of the filling body beside the roadway. When the width of the roadway-side filling body is 2.5 m, the surrounding rock convergence of the gob-side entry retaining is relatively small at only 5% of the convergence ratio. It has been shown that the figure for roof separation is relatively low, and strata behaviors are relatively alleviated and gas density do not exceed the limit, which are the best results of gob-side entry retaining. The results of this research can provide theoretical guidance for excavation of coal mines with similar geological conditions and have some referential significance to safety and efficient production in coal mines.

scholarly journals An Electroporation Device with Microbead-Enhanced Electric Field for Bacterial Inactivation

Inventions ◽  
2019 ◽  
Vol 5 (1) ◽  
pp. 2 ◽  
Author(s):  
Sanam Pudasaini ◽  
A. T. K. Perera ◽  
Syed. S. U. Ahmed ◽  
Yong Bing Chong ◽  
Sum Huan Ng ◽  
...  
Keyword(s):  
Field Strength ◽  
Electric Field ◽  
Electric Field Strength ◽  
Operating Conditions ◽  
Bacterial Cells ◽  
Bacterial Inactivation ◽  
Positive Bacterium ◽  
Applied Electric Field Strength ◽  
Comparison Results ◽  
Local Electric Field Strength

This paper presents an electroporation device with high bacterial inactivation performance (~4.75 log removal). Inside the device, insulating silica microbeads are densely packed between two mesh electrodes that enable enhancement of the local electric field strength, allowing improved electroporation of bacterial cells. The inactivation performance of the device is evaluated using two model bacteria, including one Gram-positive bacterium (Enterococcus faecalis) and one Gram-negative bacterium (Escherichia coli) under various applied voltages. More than 4.5 log removal of bacteria is obtained for the applied electric field strength of 2 kV/cm at a flowrate of 4 mL/min. The effect of microbeads on the inactivation performance is assessed by comparing the performance of the microbead device with that of the device having no microbeads under same operating conditions. The comparison results show that only 0.57 log removal is achieved for the device having no microbeads—eightfold lower than for the device with microbeads.

scholarly journals Experimental and Numerical Study of Rock Stratum Movement Characteristics in Longwall Mining

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Wan-rong Liu
Keyword(s):  
Stress Concentration ◽  
Coal Seam ◽  
Longwall Mining ◽  
Roof Rock ◽  
Numerical Study ◽  
High Stress ◽  
Engineering Practice ◽  
Rock Stratum ◽  
Working Face ◽  
Coal Wall

The roof fracture is the main cause of coal mine roof accidents. To analyze the law of movement and caving of the roof rock stratum, the roof subsidence displacement, rock stratum stress, and the rock stratum movement law were analyzed by using the methods of the particle discrete element and similar material simulation test. The results show that (1) as the working face advances, regular movement and subsidence appears in the roof rock strata, and the roof subsidence curve forms a typical “U” shape. As the coal seam continues to advance, the maximum subsidence displacement remains basically constant, and the subsidence displacement curves present an asymmetric flat-bottomed distribution. (2) After the coal seam is mined, the overburden forms an arched shape force chain, and the arched strong chain is the path of the overburden transmission force. The farther away from the coal seam, the smaller the stress concentration coefficient is, but it is still in a high stress area, and the stress concentration position moves toward the middle area of the goaf. The stress concentration in front of the coal wall is the source of force that forms the abutment pressure. (3) Above the coal wall towards the goaf, a stepped fracture was formed in the roof rock stratum. The periodic fracture of the rock stratum is the main cause of the periodic weighting of the working face. Understanding the laws of rock movement and stress distribution is of great significance for guiding engineering practice and preventing the roof accidents.

Sign in / Sign up

Export Citation Format

Share Document