scholarly journals Hysteresis and Soil Site Dependent Input and Hysteretic Energy Spectra for Far-Source Ground Motions

2016 ◽  
Vol 2016 ◽  
pp. 1-29 ◽  
Author(s):  
Mebrahtom Gebrekirstos Mezgebo ◽  
Eric M. Lui
Keyword(s):  
Ground Motions ◽  
Time History ◽  
Response Spectra ◽  
Energy Spectra ◽  
Period Range ◽  
Hysteretic Energy ◽  
Soil Site ◽  
Large Period ◽  
Motion Effect ◽  
Nonlinear Time History

Earthquake input energy spectra for four soil site classes, four hysteresis models, and five ductility levels are developed for far-source ground motion effect. These energy spectra are normalized by a quantity called velocity index (VI). The use of VI allows for the creation of dimensionless spectra and results in smaller coefficients of variation. Hysteretic energy spectra are then developed to address the demand aspect of an energy-based seismic design of structures with 5% critical damping and ductility that ranges from 2 to 5. The proposed input and hysteretic energy spectra are then compared with response spectra generated using nonlinear time history analyses of real ground motions and are found to produce reasonably good results over a relatively large period range.

Seismic response analysis of steel–concrete hybrid wind turbine tower

2021 ◽  
pp. 107754632110075
Author(s):  
Junling Chen ◽  
Jinwei Li ◽  
Dawei Wang ◽  
Youquan Feng
Keyword(s):  
Wind Turbine ◽  
Response Spectrum ◽  
Ground Motions ◽  
Time History ◽  
Seismic Action ◽  
Response Spectrum Method ◽  
Spectrum Method ◽  
Wind Turbine Tower ◽  
Ground Types ◽  
Nonlinear Time History

The steel–concrete hybrid wind turbine tower is characterized by the concrete tubular segment at the lower part and the traditional steel tubular segment at the upper part. Because of the great change of mass and stiffness along the height of the tower at the connection of steel segment and concrete segment, its dynamic responses under seismic ground motions are significantly different from those of the traditional steel tubular wind turbine tower. Two detailed finite element models of a full steel tubular tower and a steel–concrete hybrid tower for 2.0 MW wind turbine built in the same wind farm are, respectively, developed by using the finite element software ABAQUS. The response spectrum method is applied to analyze the seismic action effects of these two towers under three different ground types. Three groups of ground motions corresponding to three ground types are used to analyze the dynamic response of the steel–concrete hybrid tower by the nonlinear time history method. The numerical results show that the seismic action effect by the response spectrum method is lower than those by the nonlinear time history method. And then it can be concluded that the response spectrum method is not suitable for calculating the seismic action effects of the steel–concrete hybrid tower directly and the time history analyses should be a necessary supplement for its seismic design. The first three modes have obvious contributions on the dynamic response of the steel–concrete hybrid tower.

Seismic Analysis of High Pier Three-Span Continuous Bridge

2015 ◽  
Vol 744-746 ◽  
pp. 890-893
Author(s):  
Xun Wu ◽  
Yong Lan Zhang
Keyword(s):  
Seismic Analysis ◽  
Linear Time ◽  
Time History ◽  
Response Spectra ◽  
Elastic Response ◽  
Modeling And Analysis ◽  
Continuous Beam Bridge ◽  
Comparison Results ◽  
Elastic Response Spectra ◽  
Nonlinear Time History

In this paper, SAP2000 and ANSYS software are used to modeling and analysis athree-span continuous beam bridge with high piers case study.By using differentbearing types and combinations to form different options, create two finiteelement models.Analysis dynamic characteristics ,elastic response spectra,linear time history and nonlinear time history .And focus on comparing dynamiccharacteristics of the earthquake response of the two programs .Running outputdata processing and comparison results show that the application of thedifferent parameters of the rational combination of rubber bearing basin bridgearrangement has better seismic performance.

scholarly journals Comparison of Scaling Ground Motions Using Arithmetic with Logarithm Values for Spectral Matching Procedure

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Rui Zhang ◽  
Dong-sheng Wang ◽  
Xiao-yu Chen ◽  
Hong-nan Li
Keyword(s):  
Ground Motions ◽  
Time History ◽  
Response Spectra ◽  
Time History Analysis ◽  
Spectral Matching ◽  
Moment Resisting Frame ◽  
History Analysis ◽  
Moment Resisting ◽  
Structural Responses ◽  
Structural Time

In recent studies, spectral matching is the most commonly proposed method for selecting earthquake records for time-history analysis of structures. However, until now, there have been no serious investigations of the effects of coordinate values on the scaling of ground motions. This paper investigated the influence of using arithmetic and logarithmic values of response spectra in spectral matching procedures (i.e., ASM and LSM methods) on the results of nonlinear structural time-history analysis. Steel moment resisting frame structures of the 3-, 9-, and 20-stories, which represent low-, medium-, and high-rise buildings, respectively, were used as examples. Structural benchmark responses were determined by calculating the arithmetic mean and median of peak interstory drift ratio (PIDR) demands based on the three record sets developed by the American SAC Steel Project. The three record sets represent seismic hazard levels with 50%, 10%, and 2% probabilities exceeded in 50 years, and their average acceleration spectra were also taken as the target spectrum. Moreover, another 40 record components for selection were scaled both by ASM and LSM methods. The seven components whose spectra were best compatible with the target spectra were selected for the structural time-history analysis. The scale factors obtained by the LSM method are nearly larger than that of the ASM method, and their ranking and selection of records are different. The estimation accuracies of structural mean (median) responses by both methods can be controlled within an engineering acceptable range (±20%), but the LSM method may cause larger structural responses than the ASM method. The LSM method has a better capacity for reducing the variability of structural responses than the ASM method, and this advantage is more significant for longer-period structures (e.g., 20-story structure) with more severe nonlinear responses.

scholarly journals Energy-Based Seismic Design Method for EBFs Based on Hysteretic Energy Spectra and Accumulated Ductility Ratio Spectra

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Cuiling Ma
Keyword(s):  
Seismic Design ◽  
Design Method ◽  
Time History ◽  
Soil Classification ◽  
Nonlinear Static Analysis ◽  
Energy Spectra ◽  
Hysteretic Energy ◽  
Shear Links ◽  
Seismic Design Method ◽  
Ductility Ratio

In the case of far field earthquakes, structural failure often results from accumulated damage caused by cyclic effects and gradual accumulation of energy. This paper proposes an energy-based seismic design method for steel eccentrically braced frames (EBFs) with two shear links at every story according to the energy balance concept. The proposed method is theoretically supported by hysteretic energy spectra and accumulated ductility ratio spectra according to the Chinese soil classification. Furthermore, the method can be used to clarify the relationship between cumulative hysteretic energy and one-way pushover energy. For developing the method, it is assumed that all the hysteretic energy is dissipated by the shear links, column bases, and beam ends of the frames at both sides. Therefore, the parts outside the links, including beam segments, braces, and columns, are specially designed to perform elastically during an earthquake. Furthermore, a V-scheme steel EBF with ten stories and three spans is designed. The seismic performances of the designed structure, such as story drift and energy dissipation, are evaluated by nonlinear static analysis and time-history analysis. Finally, the reliability and accuracy of the proposed seismic design method are validated.

DAMAGE EVOLUTION SPECTRA FOR SEISMIC ANALYSIS OF HIGH-RISE BUILDINGS

2012 ◽  
Vol 06 (03) ◽  
pp. 1250021
Author(s):  
Y. B. HO ◽  
J. S. KUANG
Keyword(s):  
Damage Evolution ◽  
Seismic Analysis ◽  
Ground Motions ◽  
Time History ◽  
Tall Buildings ◽  
Response Spectra ◽  
Seismic Damage ◽  
Analysis And Design ◽  
High Rise ◽  
Earthquake Ground Motions

Seismic response spectra are amongst one of the most important tools for characterizing earthquake ground motions. In design practice, the response spectra are presented without including any load history, hence the nonlinear analysis of structures based solely on conventional earthquake response spectra is theoretically unsound, particularly for long-period or vertically irregular high-rise buildings. In this paper, a concept of seismic damage evolution is introduced and the method of analysis for characterizing the process of seismic damage to structures under earthquakes is presented. Seismic damage evolution spectra for analysis and design of high-rise buildings are then developed as an effective means of describing and simplifying earthquake ground motions. These spectra are shown to be very useful in selecting the ground motion-time history and, particularly, validating the equivalent static-load analysis and design of high-rise buildings under near-fault pulse-like ground motions. Case studies of the seismic inelastic performance of two vertically irregular, tall buildings are presented considering the seismic damage evolution spectra.

Influence of Earthquake Attack Angle on Seismic Demands for Structures under Bi-Directional Ground Motions

2011 ◽  
Vol 255-260 ◽  
pp. 2330-2334 ◽  
Author(s):  
Yu Zhang ◽  
Quan Wang Li ◽  
Jian Sheng Fan
Keyword(s):  
Seismic Design ◽  
Ground Motions ◽  
Time History ◽  
Earthquake Excitation ◽  
Seismic Demands ◽  
3 Dimensional ◽  
Nonlinear Time History Analyses ◽  
Modification Factor ◽  
Structural Responses ◽  
Nonlinear Time History

The earthquake may attack the structural building from any angle, but in current seismic design codes, this type of uncertainty is seldom accounted. The uncertainty associated with the direction of earthquake excitation was considered in this paper, and its effect on structural responses was investigated. For this purpose, a simple 3-dimensional model with symmetric plan was established, which had fundamental periods ranged from 0.1s to 5.0s, and was subjected to a set of 30 ground motion pairs for which both linear and nonlinear time history analyses were performed. Analyzing results showed that, on average, the elastic roof acceleration is 32% underestimated, and the inelastic roof displacement is 18% underestimated if the variation of earthquake excitation direction is not consider. Recognizing this, a modification factor for the seismic demand was proposed thorough a statistical analysis, which guarantees a probability of 95% design safety

scholarly journals Isolating system using U Shaped steel damper

2021 ◽  
Vol 309 ◽  
pp. 01136
Author(s):  
Siripuram Vamshisheela ◽  
Atulkumar Manchalwar
Keyword(s):  
Base Isolation ◽  
Ground Motions ◽  
Time History ◽  
Nonlinear Time History Analysis ◽  
Base Shear ◽  
Energy Device ◽  
History Analysis ◽  
Structural Responses ◽  
Nonlinear Time History ◽  
Story Building

In this work the performance of U-Shaped Steel Isolator is evaluated for a 5-story building subjected to seismic and blast vibrations. The structure is analysed using SAP 2000 software and a nonlinear time history analysis is carried out. The effectiveness of using base isolation is studied by comparing the structural responses of the building with isolator and without isolator and noticeable difference was observed. As the U-Shaped isolator absorbs the energy in all directions, it effectively controls the structural responses. In this study, the building is subjected to four different seismic and four different blast induced ground motions. It was observed that by the use of supplementary energy device there is reduction in top story acceleration, base shear and less deformation in the structure. This study concludes that the use of isolator has been effective in minimizing structural responses.

scholarly journals A Wavelet-based Approach for Truncating Pulse-like Records

2021 ◽  
Author(s):  
Vicky Dimakopoulou ◽  
Michalis Fragiadakis ◽  
Ioannis Taflampas
Keyword(s):  
Ground Motion ◽  
Near Field ◽  
Time History ◽  
Response Spectra ◽  
Degree Of Freedom ◽  
Seismic Performance Assessment ◽  
Analysis And Design ◽  
Nonlinear Time History Analyses ◽  
Ground Motion Records ◽  
Nonlinear Time History

Abstract The seismic performance assessment of structures using truncated pulse-like ground motion records is discussed. It is shown that it is possible to truncate pulse-like signals using a novel wavelet-based definition that identifies the duration of the predominant velocity pulse. The truncated time history can efficiently reproduce the increased seismic demand that near-field records typically produce. Substituting the original ground motion with the truncated signal, significantly accelerates structural analysis and design. The truncated signal is the part of the original accelerogram that coincides with the duration of the predominant pulse, which is identified using a wavelet-based procedure, previously proposed by the authors. Elastic and inelastic response spectra and nonlinear time history analyses for SDOF (single-degree-of-freedom) systems are first studied. Subsequently a nine-storey steel frame is examined in order to demonstrate the performance of the proposed approach on a multiple-degree-of-freedom system. The proposed approach is found very efficient for pulse-like ground motions, while it is also sufficient for many records that are not characterized as such.

Significance of Ground Motion Scaling Parameters on Amplitude of Scale Factors and Seismic Response of Short- and Long-Period Structures

2019 ◽  
Vol 35 (4) ◽  
pp. 1663-1688 ◽  
Author(s):  
Esengul Cavdar ◽  
Gokhan Ozdemir ◽  
Beyhan Bayhan
Keyword(s):  
Seismic Response ◽  
Ground Motion ◽  
Ground Motions ◽  
Response Spectra ◽  
Scaling Method ◽  
Period Range ◽  
Long Period ◽  
Scale Factors ◽  
Short Period ◽  
Response History Analysis

In this study, an ensemble of ground motions is selected and scaled in order to perform code-compliant bidirectional Nonlinear Response History Analysis for the design purpose of both short- and long-period structures. The followed scaling method provides both the requirements of the Turkish Earthquake Code regarding the scaling of ground motions and compatibility of response spectra of selected ground motion pairs with the target spectrum. The effects of four parameters, involved in the followed scaling method, on both the amplitude of scale factors and seismic response of structures are investigated. These parameters are the number of ground motion records, period range, number of periods used in the related period range, and distribution of weight factors at the selected periods. In the analyses, ground motion excitations were applied to both fixed-base and seismically isolated structure models representative of short- and long-period structures, respectively. Results revealed that both the amplitudes of scale factors and seismic response of short-period structures are more prone to variation of investigated parameters compared to those of long-period structures.

Earthquake time histories compatible with the 2005 National building code of Canada uniform hazard spectrum

2009 ◽  
Vol 36 (6) ◽  
pp. 991-1000 ◽  
Author(s):  
Gail M. Atkinson
Keyword(s):  
Ground Motions ◽  
Time History ◽  
Building Code ◽  
Site Condition ◽  
Period Range ◽  
Uniform Hazard Spectrum ◽  
Finite Fault ◽  
Time Histories ◽  
Finite Fault Method ◽  
Site Classes

The seismic design provisions of the 2005 National building code of Canada (NBCC) (NRC 2005) describe earthquake ground motions for which structures are to be designed in terms of a uniform hazard spectrum (UHS) having a 2% chance of being exceeded in 50 years. The “target” UHS depends on location and site condition, where site condition is described by a classification scheme based on the time-averaged shear-wave velocity in the top 30 m of the deposit. For some applications, such as dynamic analysis by time history methods, it is useful to have time histories that represent the types of earthquake motions expected and match the target UHS from the NBCC over some prescribed period range. In this study, the stochastic finite-fault method is used to generate earthquake time histories that may be used to match the 2005 NBCC UHS for a range of Canadian sites. Records are provided for site classes A, C, D, and E. They are freely available at www.seismotoolbox.ca .

Sign in / Sign up

Export Citation Format

Share Document