scholarly journals Experimental Study of the Gas Engine Driven Heat Pump with Engine Heat Recovery

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Wei Zhang ◽  
Tao Wang ◽  
Sulu Zheng ◽  
Xueyuan Peng ◽  
Xiaolin Wang
Keyword(s):  
Ambient Temperature ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Heat Recovery ◽  
Engine Speed ◽  
Water Flow Rate ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Gas Engine

Gas engine driven heat pumps (GEHPs) represent one of practical solutions to effectively utilize fossil fuel energy and reduce environmental pollution. In this paper, the performance characteristics of the GEHP were investigated experimentally with engine heat recovery. A GEHP test facility was set up for this purpose. The effects of several important factors including engine speed, ambient temperature, condenser water flow rate, and condenser water inlet temperature on the system performance were studied over a wide range of operating conditions. The results showed that the engine waste heat accounted for about 40–50% of the total heat capacity over the studied operating conditions. It also showed that engine speed and ambient temperature had significant effects on the GEHP performance. The coefficient of performance (COP) and the primary energy ratio (PER) decreased by 14% and 12%, respectively, as engine speed increased from 1400 rpm to 2000 rpm. On the other hand, the COP and PER of the system increased by 22% and 16%, respectively, with the ambient temperature increasing from 3 to 12°C. Furthermore, it was demonstrated that the condenser water flow rate and condenser water inlet temperature had little influence on the COP of the heat pump and the PER of the GEHP system.

scholarly journals An experimental investigation on the coefficient of performance of the small hot water heat pump using refrigeration R410A and R32

2020 ◽  
Vol 3 (2) ◽  
pp. First
Author(s):  
Le Minh Nhut ◽  
Tran Quang Danh
Keyword(s):  
Ambient Temperature ◽  
Water Temperature ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Electric Heater ◽  
Initial Water

Hot water is an important factor in domestic life and industrial development. Today, the heat pump is used to produce hot water more and more popular because it has many advantages of saving energy compared to the method of producing hot water by the hot water electric heater. The main aim of this study is to evaluate of the coefficient of performance (COP) of the small hot water heat pump using refrigeration R410A and R32. The capacity of both hot water heat pump is similar, one using new refrigerant R32 and other using refrigerant R410A. These heat pumps were designed and installed at the Ho Chi Minh City University of Technology and Education to evaluate the COP for the purpose of application the new refrigerant R32 for hot water heat pump. The compressor capacity is 1 Hp, the volume of hot water storage tank is of 100 liters and is insulated with thickness of 30 mm to reduce the heat loss to invironment, the required hot water temperature at the outlet of condenser is 50 oC, and the amount of required hot water is 75 liters per batch and is controlled by float valve. The experimental results indicate that the COP of the heat pump using the new refrigerant R32 is higher than heat pump using refrigerant R410A from 9% to 15% when the experimental conditions such as ambient temperature, initial water flow rate through the condenser and the required temperature of hot water were the same. In addition, the effect of the ambient temperature, initial water temperature and water flow rate were also evaluated.

scholarly journals Mapping Relevant Parameters for Efficient Operation of Low-Temperature Heating Systems in Nordic Single-Family Dwellings

2018 ◽  
Vol 8 (10) ◽  
pp. 1973 ◽  
Author(s):  
Adnan Ploskić ◽  
Qian Wang ◽  
Sasan Sadrizadeh
Keyword(s):  
Low Temperature ◽  
Environmental Impact ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Single Family ◽  
Efficient Operation ◽  
Heating Systems

The aim of this study was to map the parameters that have the greatest impact on the environmental impact of heating systems usually used in Nordic single-family dwellings. The study focused on mapping the technical requirements for efficient operation of heating systems in a broader context. The results suggest that the ability of a heating system to be operated with a low-temperature water supply depends to a large extent on the heating demand of a building. It was shown that an increase in the water flow rate in hydronic circuits would significantly increase the thermal efficiency from analyzed heating systems. This increase would not increase the pumping power need, nor would it create noise problems in distribution network if the distribution pipes and thermostatic valves were properly selected. However, this increase in water flow rate improved the efficiency of considered closed-loop heat pump. It was further shown that the efficiency of the heat pump could be additionally improved by halving the energy needs for the domestic hot-water and circulators. The main conclusion from this study is that exergy usage, CO2 emission and thereby environmental impact are significantly lower for heating systems that are operated with small temperature drops.

Experimental Study on the Desalination System Using Humidification-Dehumidification Technology

2020 ◽  
Vol 1008 ◽  
pp. 177-185
Author(s):  
Hamed Abbady ◽  
Mahmoud Salem Ahmed ◽  
Hamdy Hassan ◽  
A.S.A. Mohamed
Keyword(s):  
Water Temperature ◽  
Water Flow ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Cooling Water ◽  
Operating Conditions ◽  
Outlet Temperature ◽  
Major Objective ◽  
Cooling Water Flow Rate ◽  
Output Ratio

In this paper, an experimental work studies the principal operating parameters of a proposed desalination process using air humidification-dehumidification method. The major objective of this work is to determine the humid air behavior through the desalination system. Different operating conditions including the effect of the water temperature at the entry to the humidifier, the ratio of the mass of water to the air, the air/water flow rate, and cooling water at entry the dehumidifier on the desalination performance were studied. The results show that the freshwater increases with increasing the water temperature at the inlet of the humidifier, the ratio of the mass of water to air, and cooling water flow rate in the dehumidifier. Cooling water outlet temperature at the condenser increases with increasing the water temperature at humidifier inlet. Also, it decreases as increasing cooling water flow rate while the ratio of the mass of water to air achieves the highest productivity and gained output ratio (GOR). The achieved mass ratio (MR) is 4.5 and the mass flow rate of air is 0.8 kg/min.

scholarly journals ANALISIS EKSPERIMEN LAJU ALIRAN VOLUME AIR TERHADAP TEMPERATUR AIR PANAS PADA HEAT RECOVERY SISTEM AC JENIS WATER CHILLER

2011 ◽  
Vol 1 (2) ◽  
Author(s):  
I Made Rasta
Keyword(s):  
Water Temperature ◽  
Water Flow ◽  
Flow Rate ◽  
Heat Recovery ◽  
Tap Water ◽  
Water Flow Rate ◽  
Maximum Heat ◽  
Heating Water ◽  
Compressor Work ◽  
Heat Released

Refrigerant in refrigeration machines will absorb heat from a room space and released the heat to the environment. The heat balancing in the system is heat released from condenser equal with heat absorbed from room space added by the heat equivalent from compressor work. Based on this heat cycle, the writer try to conduct research on using this heat rejection from condenser to heating tap water, focusing on water flow rate increased from 0.5 liter/min to 2.5 liter/min. From experiment and analysis result obtained that the maximum heat water temperature which can be reached is 47.5°C in 0.5 liter/min, with the equipment specifications are 2 HP- split air conditioning and the tank volume is 75 liters. The additional result is heating water temperature is fallen when the water flow rate is increased.

scholarly journals Investigation of the influence of operation conditions on the discharge of PCM ceiling panels.

2019 ◽  
Vol 111 ◽  
pp. 03021
Author(s):  
José Quesada Allerhand ◽  
Ongun Berk Kazanci ◽  
Bjarne W. Olesen
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Thermal Environment ◽  
Water Discharge ◽  
Water Flow Rate ◽  
Water Circulation ◽  
Operating Conditions ◽  
Cooling Period ◽  
Operation Conditions ◽  
Office Rooms

The aim of this study was to determine favorable operation conditions for ceiling panels containing phase change materials (PCM) for cooling applications in office rooms. A recently renovated room in the Technical University of Denmark was used to have realistic boundary conditions. Using TRNSYS 17, the performance of the PCM panels during the cooling season in passive operation, discharge by air, and discharge by water circulation were investigated. A set of simulations were performed during a representative week in the cooling period. The room was simulated with no climatic systems, PCM without active discharge, ventilation during occupied hours only, and PCM with ventilation during occupied hours. Afterwards, two discharge methods were investigated, night ventilation at different flow rates and water circulation in pipes embedded in the panels. A parametric analysis was performed to identify the influence of operation factors in the thermal environment of the room. The parameters studied were the water flow rate, supply water temperature and circulation schedule as well as the conductivity of the PCM. After selecting different operating conditions of the water discharge, simulations were performed from May to October to observe the performance of the selected operation conditions. The results show that the PCM is more effective to provide adequate indoor thermal conditions if it is discharged actively by means of water. The parameters that affect the thermal indoor environment the most are the water circulation schedule, the water supply temperature, and the PCM thermal conductivity. The water flow rate did not have a significant influence. The study shows the importance of selecting an appropriate operation and control strategy for the PCM system. The process used in the study can be potentially used as a procedure for the design of similar climatic systems to determine if active discharge of the PCM is needed and if yes, which discharge method is needed.

scholarly journals Operating characteristics of transcritical CO2 heat pump for simultaneous water cooling and heating

2011 ◽  
Vol 33 (4) ◽  
pp. 23-40 ◽  
Author(s):  
Jahar Sarkar ◽  
Souvik Bhattacharyya
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Water Mass ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Water Cooling ◽  
Operating Characteristics ◽  
Water Mass Flow Rate

Abstract The effects of water-side operating conditions (mass flow rates and inlet temperatures) of both evaporator and gas cooler on the experimental as well as simulated performances (cooling and heating capacities, system coefficient of performance (COP) and water outlet temperatures) of the transcritical CO2 heat pump for simultaneous water cooling and heating the are studied and revised. Study shows that both the water mass flow rate and inlet temperature have significant effect on the system performances. Test results show that the effect of evaporator water mass flow rate on the system performances and water outlet temperatures is more pronounced (COP increases by 0.6 for 1 kg/min) compared to that of gas cooler water mass flow rate (COP increases by 0.4 for 1 kg/min) and the effect of gas cooler water inlet temperature is more significant (COP decreases by 0.48 for given range) compared to that of evaporator water inlet temperature (COP increases by 0.43 for given range). Comparisons of experimental values with simulated results show the maximum deviation of 5% for cooling capacity, 10% for heating capacity and 16% for system COP.

scholarly journals Development of Operating Method of Multi-Geothermal Heat Pump Systems Using Variable Water Flow Rate Control and a COP Prediction Model Based on ANN

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3894 ◽  
Author(s):  
Ji-Hyun Shin ◽  
Yong-In Kim ◽  
Young-Hum Cho
Keyword(s):  
Prediction Model ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Geothermal Heat Pump ◽  
Operating Method

As the global energy trend continues, the importance of energy savings and efficient use is being emphasized, and the installation and operation of geothermal heat pump systems is increasing. In many buildings, where an actual geothermal heat pump system has been installed, problems of efficiency deterioration occur frequently because of the inefficient operation after installation of the heat pump system. The purpose of this study was to develop and verify the operating method for energy saving and performance improvement of multiple geothermal systems. A coefficient of performance (COP) prediction model using an artificial neural network for real-time COP predictions was developed. The operating method of a multi-geothermal heat pump system using a variable water flow rate control method and COP prediction model was developed. The geothermal heat pump system operates sequentially depending on the water flow rate of the circulation pump. The COP prediction model enabled real-time performance prediction during system operation. The circulation water flow rate was reduced by up to 29% compared to the existing operating method. Approximately 23% of the energy was saved. The COP system, including the consumption power of the circulation pump, was improved.

Sign in / Sign up

Export Citation Format

Share Document