scholarly journals Conjugate Heat Transfer Study at Interior Surface of NGV Leading Edge with Combined Shower Head and Impingement Cooling

2014 ◽  
Vol 2014 ◽  
pp. 1-14 ◽  
Author(s):  
Arun Kumar Pujari ◽  
B. V. S. S. S. Prasad ◽  
N. Sitaram
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Conjugate Heat Transfer ◽  
Computational Study ◽  
Guide Vane ◽  
Internal Heat ◽  
Leading Edge ◽  
Impinging Jets ◽  
Mainstream Flow

A computational study on conjugate heat transfer is carried out to present the behavior of nondimensional temperature and heat transfer coefficient of a Nozzle Guide Vane (NGV) leading edge. Reynolds number of both mainstream flow and coolant impinging jets are varied. The NGV has five rows of film cooling holes arranged in shower head manner and four rows of impingement holes arranged in staggered manner. The results are presented by considering materials of different thermal conductivity. The results show that the mainstream flow affects the temperature distribution on the interior side of the vane leading edge for high conductivity material whereas it has negligible effects for low conductivity material. The effect of changing blowing ratio on internal heat transfer coefficient and internal surface temperature is also presented.

scholarly journals Effect of Rotation on a Gas Turbine Blade Internal Cooling System: Experimental Investigation

2016 ◽  
Author(s):  
Daniele Massini ◽  
Emanuele Burberi ◽  
Carlo Carcasci ◽  
Lorenzo Cocchi ◽  
Bruno Facchini ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Flow Field ◽  
Transfer Coefficient ◽  
Cooling System ◽  
Cross Flow ◽  
Leading Edge ◽  
Impinging Jets ◽  
Internal Cooling ◽  
Transfer Pattern

A detailed aerothermal characterization of an advanced leading edge cooling system has been performed by means of experimental measurements. Heat transfer coefficient distribution has been evaluated exploiting a steady-state technique using Thermocromic Liquid Crystals (TLC), while flow field has been investigated by means of Particle Image Velocimetry (PIV). The geometry key features are the multiple impinging jets and the four rows of coolant extraction holes, which mass flow rate distribution is representative of real engine working conditions. Tests have been performed in both static and rotating conditions, replicating a typical range of jet Reynolds number (Rej), from 10000 to 40000, and Rotation number (Roj) up to 0.05. Different cross-flow conditions (CR) have been used to simulate the three main blade regions (i.e. tip, mid and hub). The aerothermal field turned out to be rather complex, but a good agreement between heat transfer coefficient and flow field measurement has been found. In particular, jet bending strongly depends on crossflow intensity, while rotation has a weak effect on both jet velocity core and area-averaged Nusselt number. Rotational effects increase for the lower cross-flow tests. Heat transfer pattern shape has been found to be substantially Reynolds-independent.

Impact of Wall Temperature on Heat Transfer Coefficient and Aerodynamics for Three-Dimensional Turbine Blade Passage

2017 ◽  
Vol 9 (4) ◽  
Author(s):  
Roberto Maffulli ◽  
Li He
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Wall Temperature ◽  
Computational Study ◽  
Guide Vane ◽  
Three Dimensional ◽  
Correction Method ◽  
Secondary Flows ◽  
Nozzle Guide

The present work is aimed to examine how the heat transfer coefficient (HTC) and main three-dimensional (3D) passage aerodynamic features may be affected by a nonadiabatic wall temperature condition. A systematic computational study has been first carried out for a 3D nozzle guide vane (NGV) passage. The impacts of wall temperature on the secondary flows, trailing edge shock waves, and the passage flow capacity are discussed, underlining the connection and interactions between the wall temperature and the external aerodynamics of the 3D passage. The local discrepancies in HTC in these 3D flow regions can be as high as 30–40% when comparing low and high temperature ratio cases. The effort is then directed to a new three-point nonlinear correction method. The benefit of the three-point method in reducing errors in HTC is clearly demonstrated. A further study illustrates that the new method also offers much enhanced robustness in the wall heat flux scaling, particularly relevant when the wall thermal condition is also shown to influence the laminar–turbulent transition exhibited by two well-established transition models adopted in the present work.

scholarly journals Effect of Rotation on a Gas Turbine Blade Internal Cooling System: Experimental Investigation

2017 ◽  
Vol 139 (10) ◽  
Author(s):  
Daniele Massini ◽  
Emanuele Burberi ◽  
Carlo Carcasci ◽  
Lorenzo Cocchi ◽  
Bruno Facchini ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Flow Field ◽  
Transfer Coefficient ◽  
Cooling System ◽  
Leading Edge ◽  
Impinging Jets ◽  
Internal Cooling ◽  
Coefficient Distribution ◽  
Transfer Pattern

A detailed aerothermal characterization of an advanced leading edge (LE) cooling system has been performed by means of experimental measurements. Heat transfer coefficient distribution has been evaluated exploiting a steady-state technique using thermochromic liquid crystals (TLCs), while flow field has been investigated by means of particle image velocimetry (PIV). The geometry key features are the multiple impinging jets and the four rows of coolant extraction holes, and their mass flow rate distribution is representative of real engine working conditions. Tests have been performed in both static and rotating conditions, replicating a typical range of jet Reynolds number (Rej), from 10,000 to 40,000, and rotation number (Roj) up to 0.05. Different crossflow conditions (CR) have been used to simulate the three main blade regions (i.e., tip, mid, and hub). The aerothermal field turned out to be rather complex, but a good agreement between heat transfer coefficient and flow field measurement has been found. In particular, jet bending strongly depends on crossflow intensity, while rotation has a weak effect on both jet velocity core and area-averaged Nusselt number. Rotational effects increase for the lower crossflow tests. Heat transfer pattern shape has been found to be substantially Reynolds independent.

scholarly journals Adiabatic Effectiveness and Heat Transfer Coefficient of Shaped Film Cooling Holes on a Scaled Guide Vane Pressure Side Model

2004 ◽  
Vol 10 (5) ◽  
pp. 345-354 ◽  
Author(s):  
Jan Dittmar ◽  
Achmed Schulz ◽  
Sigmar Wittig
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Guide Vane ◽  
Inlet Temperature ◽  
Test Model ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

The demand of improved thermal efficiency and high power output of modern gas turbine engines leads to extremely high turbine inlet temperature and pressure ratios. Sophisticated cooling schemes including film cooling are widely used to protect the vanes and blades of the first stages from failure and to achieve high component lifetimes. In film cooling applications, injection from discrete holes is commonly used to generate a coolant film on the blade's surface.In the present experimental study, the film cooling performance in terms of the adiabatic film cooling effectiveness and the heat transfer coefficient of two different injection configurations are investigated. Measurements have been made using a single row of fanshaped holes and a double row of cylindrical holes in staggered arrangement. A scaled test model was designed in order to simulate a realistic distribution of Reynolds number and acceleration parameter along the pressure side surface of an actual turbine guide vane. An infrared thermography measurement system is used to determine highly resolved distribution of the models surface temperature. Anin-situcalibration procedure is applied using single embedded thermocouples inside the measuring plate in order to acquire accurate local temperature data.All holes are inclined 35° with respect to the model's surface and are oriented in a streamwise direction with no compound angle applied. During the measurements, the influence of blowing ratio and mainstream turbulence level on the adiabatic film cooling effectiveness and heat transfer coefficient is investigated for both of the injection configurations.

Numerical Study on the Influence of Trench Width on Film Cooling Characteristics of Double-Wave Trench

2017 ◽  
Author(s):  
Bo-lun Zhang ◽  
Li Zhang ◽  
Hui-ren Zhu ◽  
Jian-sheng Wei ◽  
Zhong-yi Fu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Numerical Study ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Trench Width

Film cooling performance of the double-wave trench was numerically studied to improve the film cooling characteristics. Double-wave trench was formed by changing the leading edge and trailing edge of transverse trench into cosine wave. The film cooling characteristics of transverse trench and double-wave trench were numerically studied using Reynolds Averaged Navier Stokes (RANS) simulations with realizable k-ε turbulence model and enhanced wall treatment. The film cooling effectiveness and heat transfer coefficient of double-wave trench at different trench width (W = 0.8D, 1.4D, 2.1D) conditions are investigated, and the distribution of temperature field and flow field were analyzed. The results show that double-wave trench effectively improves the film cooling effectiveness and the uniformity of jet at the downstream wall of the trench. The span-wise averaged film cooling effectiveness of the double-wave trench model increases 20–63% comparing with that of the transverse trench at high blowing ratio. The anti-counter-rotating vortices which can press the film on near-wall are formed at the downstream wall of the double-wave trench. With the double-wave trench width decreasing, the film cooling effectiveness gradually reduces at the hole center-line region of the downstream trench. With the increase of the blowing ratio, the span-wise averaged heat transfer coefficient increases. The span-wise averaged heat transfer coefficient of the double-wave trench with 0.8D and 2.1D trench width is higher than that of the double-wave trench with 1.4D trench width at the high blowing ratio conditions.

scholarly journals Local Heat Transfer Coefficient and Adiabatic Wall Temperature Measurement Beneath Arrays of Staggered and Inline Impinging Jets

1994 ◽  
Author(s):  
Kenneth W. Van Treuren ◽  
Zuolan Wang ◽  
Peter T. Ireland ◽  
Terry V. Jones ◽  
S. T. Kohler
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Wall Temperature ◽  
Impinging Jets ◽  
Hole Diameter ◽  
Channel Height ◽  
Published Data ◽  
Target Plate ◽  
Adiabatic Wall

Recent work, Van Treuren et al. (1993), has shown the transient method of measuring heat transfer under an array of impinging jets allows the determination of local values of adiabatic wall temperature and heat transfer coefficient over the complete surface of the target plate. Using this technique, an inline array of impinging jets has been tested over a range of average jet Reynolds numbers (10,000–40,000) and for three channel height to jet hole diameter ratios (1, 2, and 4). The array is confined on three sides and spent flow is allowed to exit in one direction. Local values are averaged and compared with previously published data in related geometries. The current data for a staggered array is compared to those from an inline array with the same hole diameter and pitch for an average jet Reynolds number of 10,000 and channel height to diameter ratio of one. A comparison is made between intensity and hue techniques for measuring stagnation point and local distributions of heat transfer. The influence of the temperature of the impingement plate through which the coolant gas flows on the target plate heat transfer has been quantified.

The Measurement of Full-Surface Internal Heat Transfer Coefficients for Turbine Airfoils Using a Non-Destructive Thermal Inertia Technique

2002 ◽  
Author(s):  
Nirm V. Nirmalan ◽  
Ronald S. Bunker ◽  
Carl R. Hedlung
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
External Surface ◽  
Internal Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Turbine Airfoils ◽  
Non Destructive ◽  
Internal Heat Transfer

A new method has been developed and demonstrated for the non-destructive, quantitative assessment of internal heat transfer coefficient distributions of cooled metallic turbine airfoils. The technique employs the acquisition of full-surface external surface temperature data in response to a thermal transient induced by internal heating/cooling, in conjunction with knowledge of the part wall thickness and geometry, material properties, and internal fluid temperatures. An imaging Infrared camera system is used to record the complete time history of the external surface temperature response during a transient initiated by the introduction of a convecting fluid through the cooling circuit of the part. The transient data obtained is combined with the cooling fluid network model to provide the boundary conditions for a finite element model representing the complete part geometry. A simple 1D lumped thermal capacitance model for each local wall position is used to provide a first estimate of the internal surface heat transfer coefficient distribution. A 3D inverse transient conduction model of the part is then executed with updated internal heat transfer coefficients until convergence is reached with the experimentally measured external wall temperatures as a function of time. This new technique makes possible the accurate quantification of full-surface internal heat transfer coefficient distributions for prototype and production metallic airfoils in a totally non-destructive and non-intrusive manner. The technique is equally applicable to other material types and other cooled/heated components.

scholarly journals Heat Transfer on a Film-Cooled Rotating Blade

1999 ◽  
Author(s):  
Vijay K. Garg
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Three Dimensional ◽  
Leading Edge ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes

A multi-block, three-dimensional Navier-Stokes code has been used to compute heat transfer coefficient on the blade, hub and shroud for a rotating high-pressure turbine blade with 172 film-cooling holes in eight rows. Film cooling effectiveness is also computed on the adiabatic blade. Wilcox’s k-ω model is used for modeling the turbulence. Of the eight rows of holes, three are staggered on the shower-head with compound-angled holes. With so many holes on the blade it was somewhat of a challenge to get a good quality grid on and around the blade and in the tip clearance region. The final multi-block grid consists of 4784 elementary blocks which were merged into 276 super blocks. The viscous grid has over 2.2 million cells. Each hole exit, in its true oval shape, has 80 cells within it so that coolant velocity, temperature, k and ω distributions can be specified at these hole exits. It is found that for the given parameters, heat transfer coefficient on the cooled, isothermal blade is highest in the leading edge region and in the tip region. Also, the effectiveness over the cooled, adiabatic blade is the lowest in these regions. Results for an uncooled blade are also shown, providing a direct comparison with those for the cooled blade. Also, the heat transfer coefficient is much higher on the shroud as compared to that on the hub for both the cooled and the uncooled cases.

The Simulation Study of Turbulence Models for Conjugate Heat Transfer Analysis of a High Pressure Air-Cooled Gas Turbine

2010 ◽  
Author(s):  
Zhenfeng Wang ◽  
Peigang Yan ◽  
Hongfei Tang ◽  
Hongyan Huang ◽  
Wanjin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Turbulence Model ◽  
Conjugate Heat Transfer ◽  
Turbulence Models ◽  
Turbulence Characteristic ◽  
The Heat Transfer Coefficient

The different turbulence models are adopted to simulate NASA-MarkII high pressure air-cooled gas turbine. The experimental work condition is Run 5411. The paper researches that the effect of different turbulence models for the flow and heat transfer characteristics of turbine. The turbulence models include: the laminar turbulence model, high Reynolds number k-ε turbulence model, low Reynolds number turbulence model (k-ω standard format, k-ω-SST and k-ω-SST-γ-θ) and B-L algebra turbulence model which is adopted by the compiled code. The results show that the different turbulence models can give good flow characteristics results of turbine, but the heat transfer characteristics results are different. Comparing to the experimental results, k-ω-SST-θ-γ turbulence model results are more accurate and can simulate accurately the flow and heat transfer characteristics of turbine with transition flow characteristics. But k-ω-SST-γ-θ turbulence model overestimates the turbulence kinetic energy of blade local region and makes the heat transfer coefficient higher. It causes that local region temperature is higher. The results of B-L algebra turbulence model show that the results of B-L model are accurate besides it has 4% temperature error in the transition region. As to the other turbulence models, the results show that all turbulence models can simulate the temperature distribution on the blade pressure surface except the laminar turbulence model underestimates the heat transfer coefficient of turbulence flow region. On the blade suction surface with transition flow characteristics, high Reynolds number k-ε turbulence model overestimates the heat transfer coefficient and causes the blade surface temperature is high about 90K than the experimental result. Low Reynolds number k-ω standard format and k-ω-SST turbulence models also overestimate the blade surface temperature value. So it can draw a conclusion that the unreasonable choice of turbulence models can cause biggish errors for conjugate heat transfer problem of turbine. The combination of k-ω-SST-γ-θ model and B-L algebra model can get more accurate turbine thermal environment results. In addition, in order to obtain the affect of different turbulence models for gas turbine conjugate heat transfer problem. The different turbulence models are adopted to simulate the different computation mesh domains (First case and Second case). As to each cooling passages, the first case gives the wall heat transfer coefficient of each cooling passages and the second case considers the conjugate heat transfer course between the cooling passages and blade. It can draw a conclusion that the application of heat transfer coefficient on the wall of each cooling passages avoids the accumulative error. So, for the turbine vane geometry models with complex cooling passages or holes, the choice of turbulence models and the analysis of different mesh domains are important. At last, different turbulence characteristic boundary conditions of turbine inner-cooling passages are given and K-ω-SST-γ-θ turbulence model is adopted in order to obtain the effect of turbulence characteristic boundary conditions for the conjugate heat transfer computation results. The results show that the turbulence characteristic boundary conditions of turbine inner-cooling passages have a great effect on the conjugate heat transfer results of high pressure gas turbine.

Sign in / Sign up

Export Citation Format

Share Document