scholarly journals Numerical Calculation on Cavitation Pressure Pulsation in Centrifugal Pump

2014 ◽  
Vol 6 ◽  
pp. 367631 ◽  
Author(s):  
Weidong Shi ◽  
Chuan Wang ◽  
Wei Wang ◽  
Bing Pei
Keyword(s):  
Numerical Calculation ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Cavitation Pressure

scholarly journals Numerical Calculation of Energy Performance and Transient Characteristics of Centrifugal Pump under Gas-Liquid Two-Phase Condition

Micromachines ◽  
2020 ◽  
Vol 11 (8) ◽  
pp. 728
Author(s):  
Ling Zhou ◽  
Yong Han ◽  
Wanning Lv ◽  
Yang Yang ◽  
Yong Zhu ◽  
...  
Keyword(s):  
Numerical Calculation ◽  
Gas Phase ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Pure Water ◽  
Energy Performance ◽  
Radial Force ◽  
Gas Content ◽  
Two Phase ◽  
Phase Condition

The unstable operation of a centrifugal pump under the gas-liquid two-phase condition seriously affects its performance and reliability. In order to study the gas phase distribution and the unsteady force in an impeller, based on the Euler-Euler heterogeneous flow model, the steady and unsteady numerical calculations of the gas-liquid two-phase full flow field in a centrifugal pump was carried out, and the simulation results were compared with the test data. The results show that the test results are in good agreement with the simulation data, which proves the accuracy of the numerical calculation method. The energy performance curve of the model pump decreases with the increase of the gas content, which illustrates a serious impact on the performance under the part-load operating condition. The results reveal that the high-efficiency-operating range become narrow, as the gas content increases. The gas phase is mainly distributed on the suction surface of the impeller blades. When the gas content reaches a certain value, the gas phase separation occurs. As the inlet gas content increases, the radial force on the impeller blades decreases. The pattern of the pressure pulsation is similar to that under pure water and low gas content conditions, and the number of peaks during the pulsation is equal to the number of the impeller blades. After the gas content reaches a certain value, the pressure fluctuates disorderly and the magnitude and the direction of radial force change frequently, which are detrimental to the operation stability of the pump. The intensity of the pressure pulsations in the impeller flow channel continues to increase in the direction of the flow under pure water conditions. The pressure pulsation intensities at the blade inlet and the volute tongue become more severe with the increase of the gas content.

scholarly journals Experiment and simulation about the effect of wear-ring abrasion on the performance of a marine centrifugal pump

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199811
Author(s):  
Wu Xianfang ◽  
Du Xinlai ◽  
Tan Minggao ◽  
Liu Houlin
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Vibration Velocity ◽  
Test Results ◽  
Obvious Effect ◽  
Performance Change ◽  
Pump Test ◽  
Simulation Results ◽  
Axis Passing

The wear-ring abrasion can cause performance degradation of the marine centrifugal pump. In order to study the effect of front and back wear-ring clearance on a pump, test and numerical simulation were used to investigate the performance change of a pump. The test results show that the head and efficiency of pump decrease by 3.56% and 9.62% respectively at 1.0 Qd due to the wear-ring abrasion. Under 1.0 Qd, with the increase of the front wear-ring the vibration velocity at pump foot increases from 0.4 mm/s to 1.0 mm/s. The axis passing frequency (APF) at the measuring points increases significantly and there appears new characteristic frequency of 3APF and 4APF. The numerical simulation results show that the front wear-ring abrasion affects the flow at the inlet of the front chamber of the pump and impeller passage. And the back wear-ring abrasion has obvious effect on the flow in the back chamber of the pump and impeller passage, while the multi-malfunction of the front wear-ring abrasion and back wear-ring abrasion has the most obvious effect on the flow velocity and flow stability inside pump. The pressure pulsation at Blade Passing Frequency (BPF) of the three schemes all decrease with the increase of the clearance.

Effects of the staggered blades on unsteady pressure pulsations and flow structures of a centrifugal pump

2021 ◽  
pp. 095765092098732
Author(s):  
Ning Zhang ◽  
Bo Gao ◽  
Chao Li ◽  
Dan Ni ◽  
Guoping Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Second Harmonic ◽  
Simulation Method ◽  
Pump Efficiency ◽  
Pressure Amplitude ◽  
Pressure Pulsations ◽  
Unsteady Pressure ◽  
Negative Effect

Effects of the staggered blades on unsteady pressure pulsations of a centrifugal pump with a specific speed ns=147 are investigated by the numerical simulation method. The obtained results are compared with the original blades. To clarify the resulting effects, eight monitoring points are used to extract pressure signals at three typical working conditions, and component at the blade passing frequency fBPF is emphasized. Results show that the pump efficiency and head will be reduced by the staggered blades, and at the nominal flow rate, the reduction is about 1.5% from comparison with the original blades. For all the eight points, the staggered blades contribute to the reduction of pressure amplitudes at fBPF when the pump works at three flow rates. The averaged reduction is 15.5% at the nominal flow rate. However, the negative effect on the second harmonic of fBPF will be caused by the staggered blades, and the corresponding pressure amplitude will increase at 2fBPF. It means that the pressure pulsation energy will be redistributed among the discrete components in pressure spectrum by the staggered blades. From the TKE distribution, it is found that the TKE values on the blade pressure side will be significantly affected by the staggered blades.

The effect of front streamline wrapping angle variation in a super-low specific speed centrifugal pump

2018 ◽  
Vol 232 (23) ◽  
pp. 4301-4311 ◽  
Author(s):  
Dong Liang ◽  
Zhao Yuqi ◽  
Liu Houlin ◽  
Dai Cui ◽  
Gradov D Vladimirovich ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Energy Performance ◽  
Sweep Angle ◽  
Angle Variation ◽  
Noise Characteristics ◽  
Ansys Cfx ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Element Method

In this research, super-low specific speed centrifugal pump ( ns = 25, Chinese units: ns = 3.6 nQ1/2/ H3/4) is studied. The effect of the front streamline wrapping angles variation (135°, 139° and 145°) of the turbine on energy performance is considered. The pressure pulsation, interior and exterior noise characteristics and the performance of the impeller are thoroughly evaluated both experimentally and numerically. The pump has been modeled by means of computational fluid dynamics code of commercial software ANSYS CFX 11.0 to estimate energy performance and pressure pulsation. Boundary element method and finite element method are used to investigate the interior and exterior noise characteristics of the centrifugal pump by varying the front sweep angle. The front sweep angle variation was found to have insignificant influence on centrifugal pump performance characteristics. However, it influences fluid hydrodynamics around the volute tongue. In addition, the decreasing of the front streamline sweep angle slightly reduces the sound pressure level for the exterior acoustics, but the radiation distribution of the acoustic field does not change. In its turn, the modified trailing edge of the blades can reduce the peak value of the superposition decreasing the pressure pulsations at the blade passing frequency and its harmonic frequencies.

Numerical investigation of flow features in the vaneless region of a centrifugal pump by large eddy simulation

2018 ◽  
Vol 35 (1) ◽  
pp. 395-410 ◽  
Author(s):  
Xianbei Huang ◽  
Yaojun Li ◽  
Zhuqing Liu ◽  
Wei Yang
Keyword(s):  
Experimental Data ◽  
Transport Equation ◽  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Pressure Pulsation ◽  
Third Order ◽  
Production Term ◽  
Content Type ◽  
Blade Passing Frequency ◽  
Rotor Stator Interaction

Purpose The purpose of this paper is to obtain a better understanding of the rotor–stator interaction in the vaneless region of a centrifugal pump. Design/methodology/approach A third-order sub-grid scale (SGS) model containing the rotation rate tensor named the dynamic cubic non-linear model (DCNM) is used for simulating the flow field in a centrifugal pump with a vaned diffuser. The pressure coefficient and velocity distributions are compared with the experimental data. Focusing on the vaneless region, the pressure pulsation, Reynolds stress pulsation and Reynolds stress transport equation are analyzed. Findings The comparison of the calculation results with the experimental data indicates that the DCNM can accurately capture the distributions of pressure and velocity in the vaneless region. Based on the instantaneous pressure signals, the pressure pulsation is analyzed to show that in the vaneless region, the dominant frequency near the impeller is twice the blade passing frequency, whereas it is equal to the blade passing frequency near the diffuser. Further exploration of the Reynolds stress pulsation shows the correlation between the two variables. Additionally, the extreme low frequency of Reynolds stress near the diffuser is found to be related to the rotation instability. To explore the turbulence characteristics in the vaneless region, the Reynolds stress transportation equation is studied. In the vaneless region, the rotation term of the Reynolds stress transport equation is negligible compared to the production term, although the rotation instability is obvious near the diffuser. The production of the Reynolds stress plays the role of redistributing the energy from the uu component to the vv component, except for the region near the impeller outlet. Originality/value The third-order SGS model DCNM has proved to be promising in simulating the rotor–stator interaction. The analysis of the rotation instability and the Reynolds stress transport equation shed light on the further understanding of the rotor–stator interaction.

scholarly journals Investigation on centrifugal pump performance degradation under air-water inlet two-phase flow conditions

2018 ◽  
pp. 41-48 ◽  
Author(s):  
Qiaorui Si ◽  
Qianglei Cui ◽  
Keyu Zhang ◽  
Jianping Yuan ◽  
Gérard Bois
Keyword(s):  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Flow Characteristics ◽  
Performance Degradation ◽  
Inlet Pressure ◽  
Pulsation Frequency ◽  
Centrifugal Pumps ◽  
Two Phase ◽  
Flow Rates ◽  
Pump Performance

In order to study the flow characteristics of centrifugal pumps when transporting the gas-liquid mixture, water and air were chosen as the working medium. Both numerical simulation and experimental tests were conducted on a centrifugal pump under different conditions of inlet air volume fraction (IAVF). The calculation used URANS k-epsilon turbulence model combined with the Euler-Euler inhomogeneous two-phase model. The air distribution and velocity streamline inside the impeller were obtained to discuss the flow characteristics of the pump. The results show that air concentration is high at the inlet pressure side of the blade, where the vortex will exist, indicating that the gas concentration have a great relationship with the vortex aggregation in the impeller passages. In the experimental works, pump performances were measured at different IAVF and compared with numerical results. Contributions to the centrifugal pump performance degradations were analyzed under different air-water inlet flow condition such as IAVF, bubble size, inlet pressure. Results show that pump performance degradation is more pronounced for low flow rates compared to high flow rates. Finally, pressure pulsation and vibration experiments of the pump model under different IAVF were also conducted. Inlet and outlet transient pressure signals under four IAVF were investigated and pressure pulsation frequency of the monitors is near the blade passing frequency at different IAVF, and when IAVF increased, the lower frequency signal is more and more obvious. Vibration signals at five measuring points were also obtained under different IAVF for various flow rates.

scholarly journals Efficiency improvement and evaluation of a centrifugal pump with vaned diffuser

2019 ◽  
Vol 11 (3) ◽  
pp. 168781401982590 ◽  
Author(s):  
Kai Wang ◽  
Yu-cheng Jing ◽  
Xiang-hui He ◽  
Hou-lin Liu
Keyword(s):  
Centrifugal Pump ◽  
Axial Force ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Energy Performance ◽  
Radial Force ◽  
Design Flow ◽  
Vaned Diffuser ◽  
Original Scheme ◽  
Design Flow Rate

In order to enhance the efficiency of centrifugal pump, the structure of a centrifugal pump with vaned diffuser, whose specific speed is 190, was numerically improved by trimming back-blades of impeller and smoothing sharp corner in annular chamber. The energy performance, the internal flow field, the axial force, the radial force, and the pressure pulsation of the pump were analyzed. Results show that efficiency of the improving scheme 1 under the design flow rate is 77.47%, which can balance 69.82% of the axial force, while efficiency of the improving scheme 2 under the design flow rate is the maximum, which could still balance 62.74% of the axial force. The pressure pulsations of the improving scheme 2 at the typical monitoring points are less than that of the improving scheme 1 and the original scheme. The difference of the radial force peak between the improving scheme 1 and the improving scheme 2 is very small. The vector distributions of the radial force of the improving scheme 1 and the improving scheme 2 are more uniform than that of the original scheme. Considering the efficiency, pressure pulsation, and axial force, experiment measurements on the improving scheme 2 were carried out to verify the effectiveness of the improvement result. Results of energy performance experiment show that efficiency of the improving scheme 2 under the design flow rate is 76.48%, which is 5.26 percentage points higher than that of the original scheme.

Numerical study on instantaneous radial force of a centrifugal pump for different working conditions

2019 ◽  
Vol 37 (2) ◽  
pp. 458-480
Author(s):  
Xiaoqi Jia ◽  
Sheng Yuan ◽  
Zuchao Zhu ◽  
Baoling Cui
Keyword(s):  
Numerical Simulation ◽  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Working Conditions ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Radial Force ◽  
Leakage Rate ◽  
Content Type ◽  
Three Components

Purpose Instantaneous radial force induced from unsteady flow will intensify vibration noise of the centrifugal pump, especially under off-design working conditions, which will affect safety reliability of pump operation in severe cases. This paper aims to conduct unsteady numerical computation on one centrifugal pump; thus, unsteady fluid radial force upon the impeller and volute is obtained, so as to study the evolution law of instantaneous radial force, the internal relationship between radial force and pressure pulsation, the relationship among each composition of radial force that the impeller received and the influence of leakage rate of front and back chamber on radial force. Design/methodology/approach The unsteady numerical simulation with SST k-ω turbulence model was carried out for a low specific-speed centrifugal pump using computational fluid dynamics codes FLUENT. The performance tests and pressure tests were conducted by a closed loop system. The performance curves and the pressure distribution from numerical simulation agree with that of the experiment conducted. The unsteady pressure distributions and the instantaneous radial forces induced from unsteady flow were analyzed under different flow rates. Contribution degrees of three components of the radial force on the impeller and the relation between the radial force and leakage rate were analyzed. Findings Radial force on the volute and pressure pulsation on the volute wall have the same distribution tendency, but in contrast to the distribution trend of the radial force on the impeller. In the component of radial force that the impeller received, radial force on the blade accounts for the main position. With the decrease of flow rate, ratio of the radial force on front and back casings will be increased; under large flow rate, vortex and flow blockage at volute section will enhance the pressure and radial force fluctuation greatly, and the pulsation degree may be much more intense than that of a smaller flow rate. Originality/value This paper revealed the relation of the radial force and the pressure pulsation. Meanwhile, contribution degrees of three components of the radial force on the impeller under different working conditions as well as the relation between the radial force and leakage rate of front and rear chambers were analyzed.

Sign in / Sign up

Export Citation Format

Share Document