scholarly journals The Pressure Drop Model of Liquid Flow with Wall Mass Transfer in Horizontal Wellbore with Perforated Completion

2014 ◽  
Vol 2014 ◽  
pp. 1-8
Author(s):  
Ping Yue ◽  
Zhimin Du ◽  
Xiaofan Chen ◽  
Chao Tang
Keyword(s):  
Mass Transfer ◽  
Single Phase ◽  
Horizontal Wells ◽  
Main Flow ◽  
Experiment Data ◽  
Proposed Model ◽  
Wellbore Pressure ◽  
Horizontal Wellbore ◽  
Wall Mass ◽  
Perforated Completion

The fluids in horizontal wells can exhibit complicated flow behaviors with wall mass transfer, partly due to the interaction between the main flow and the radial influx along the wellbore and the completion parameters used. This paper presents a novel regression model established based on the experiment data retrieved from the available literatures to determine the apparent friction factor for a single phase wellbore flow. The proposed model has the potential to be readily applicable to different perforation parameters, such as shot phasing and shot density. Compared with other models in the same practical example which is offered by Ouyang et al., the model of this paper to calculate the wellbore pressure is applicable and reasonable. This new model can be easily incorporated into reservoir simulators or analytical reservoir and horizontal wellbore inflow coupling models.

Investigation of the Effects of Completion Geometry on Single-Phase Liquid Flow Behavior in Horizontal Wells

2000 ◽  
Vol 123 (2) ◽  
pp. 119-126 ◽  
Author(s):  
Weipeng Jiang ◽  
Cem Sarica ◽  
Erdal Ozkan ◽  
Mohan Kelkar
Keyword(s):  
Liquid Flow ◽  
Horizontal Well ◽  
Single Phase ◽  
Flow Behavior ◽  
Horizontal Wells ◽  
Main Flow ◽  
Test Facility ◽  
Small Scale ◽  
Phase Liquid ◽  
Single Phase Liquid Flow

The fluids in horizontal wells can exhibit complicated flow behaviors, in part due to interaction between the main flow and the influxes along the wellbore, and due to completion geometries. An existing small-scale test facility at Tulsa University Fluid Flow Projects (TUFFP) was used to simulate the flow in a horizontal well completed with either circular perforations or slotted liners. Single phase liquid flow experiments were conducted with Reynolds numbers ranging approximately from 5000 to 65,000 and influx to main flow rate ratios ranging from 1/50 to 1/1000. For both the perforation and slot cases, three different completion densities and three different completion phasings are considered. Based on the experimental data, new friction factor correlations for horizontal well with multiple perforation completion or multiple slots completion were developed using the principles of conservation of mass and momentum.

Experimental Investigation of Methane Hydrate Formation in the Carboxmethylcellulose (CMC) Aqueous Solution

SPE Journal ◽  
2020 ◽  
Vol 25 (03) ◽  
pp. 1042-1056 ◽  
Author(s):  
Weiqi Fu ◽  
Zhiyuan Wang ◽  
Litao Chen ◽  
Baojiang Sun
Keyword(s):  
Aqueous Solution ◽  
Mass Transfer ◽  
Gas Hydrates ◽  
Methane Hydrate ◽  
Formation Rate ◽  
Hydrate Formation ◽  
Semiempirical Model ◽  
Stirred Reactor ◽  
Proposed Model ◽  
Wellbore Pressure

Summary In the development of deepwater crude oil, gas, and gas hydrates, hydrate formation during drilling operations becomes a crucial problem for flow assurance and wellbore pressure management. To study the characteristics of methane hydrate formation in the drilling fluid, the experiments of the methane hydrate formation in water with carboxmethylcellulose (CMC) additive are performed in a horizontal flow loop under flow velocity from 1.32 to 1.60 m/s and CMC concentration from 0.2 to 0.5 wt%. The flow pattern is observed as bubbly flow in experiments. The experiments indicate that the increase of CMC concentration impedes the hydrate formation while the increase of liquid velocity enhances formation rates. In the stirred reactor, the hydrate formation rate generally decreases as the subcooling condition decreases. However, in this work, with the subcooling condition continuously decreasing, hydrate formation rate follows a “U” shaped trend—initially decreasing, then leveling out and finally increasing. It is because the hydrate formation rate in this work is influenced by multiple factors, such as hydrate shell formation, fracturing, sloughing, and bubble breaking up, which has more complicated mass transfer procedure than that in the stirred reactor. A semiempirical model that is based on the mass transfer mechanism is developed for current experimental conditions, and can be used to predict the formation rates of gas hydrates in the non-Newtonian fluid by replacing corresponding correlations. The rheological experiments are performed to obtain the rheological model of the CMC aqueous solution for the proposed model. The overall hydrate formation coefficient in the proposed model is correlated with experimental data. The hydrate formation model is verified and the predicted quantity of gas hydrates has a discrepancy less than 10%.

WELL TESTING HORIZONTALGAS-CONDENSATE WELLS

2017 ◽  
pp. 56-61
Author(s):  
M. L. Karnaukhov ◽  
O. N. Pavelyeva
Keyword(s):  
Comparative Analysis ◽  
Skin Effect ◽  
Horizontal Wells ◽  
Gas Condensate ◽  
Low Permeability ◽  
Well Testing ◽  
Flow Capacity ◽  
Formation Zone ◽  
Horizontal Wellbore

The well testing of gas-condensate horizontal wells are discussed in the article and the comparative analysis of borehole flow capacity, depending on the mode of it’s operation is presented. Extra attention is focused on the issue of timely identification of the reasons for the reduction of fluid withdrawal from the reservoir. The presence of high skin effect is proved, which confirms the existence of low-permeability of bottomhole formation zone related to condensation in the immediate area of the horizontal wellbore.

scholarly journals Ball sealer tracking and seating of temporary plugging fracturing technology in the perforated casing of a horizontal well

2021 ◽  
pp. 014459872110204
Author(s):  
Wan Cheng ◽  
Chunhua Lu ◽  
Guanxiong Feng ◽  
Bo Xiao
Keyword(s):  
Critical Parameter ◽  
Fluid Velocity ◽  
Stable State ◽  
Horizontal Wells ◽  
Terminal Velocity ◽  
Injection Rate ◽  
Fracturing Fluid ◽  
Perforation Hole ◽  
Horizontal Wellbore ◽  
Tight Reservoirs

Multistaged temporary plugging fracturing in horizontal wells is an emerging technology to promote uniform fracture propagation in tight reservoirs by injecting ball sealers to plug higher-flux perforations. The seating mechanism and transportation of ball sealers remain poorly understood. In this paper, the sensitivities of the ball sealer density, casing injection rate and perforation angle to the seating behaviors are studied. In a vertical wellbore section, a ball sealer accelerates very fast at the beginning of the dropping and reaches a stable state within a few seconds. The terminal velocity of a non-buoyant ball is greater than the fluid velocity, while the terminal velocity of a buoyant ball is less than the fluid velocity. In the horizontal wellbore section, the terminal velocity of a non-buoyant or buoyant ball is less than the fracturing fluid flowing velocity. The ball sealer density is a more critical parameter than the casing injection rate when a ball sealer diverts to a perforation hole. The casing injection rate is a more critical parameter than the ball sealer density when a ball sealer seats on a perforation hole. A buoyant ball sealer associated with a high injection rate of fracturing fluid is highly recommended to improve the seating efficiency.

The Productivity of Horizontal Wells in an In-Line Development System in Fields with Oil Rims

2021 ◽  
Author(s):  
Dmitriy Alekseevich Samolovov ◽  
Artem Igorevich Varavva ◽  
Vitalij Olegovich Polyakov ◽  
Ekaterina Evgenevna Sandalova
Keyword(s):  
Numerical Experiments ◽  
Single Phase ◽  
Analytical Formula ◽  
Horizontal Wells ◽  
Flow Equation ◽  
Development Pattern ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Limited Applicability ◽  
Good Agreement

Abstract The study proposes an analytical method for calculating the productivity of horizontal wells in a line-drive development pattern in fields with oil rims. The paper presents an analysis of existing techniques and compares them with the results of detailed numerical experiments. It also shows the limited applicability of existing techniques. On the basis of the obtained solution of a single-phase flow equation for a line-drive pattern of horizontal wells, an analytical formula was obtained which more accurately describes the productivity of wells beyond the limits of applicability of existing methods. The resulting formula is in good agreement with the results of a detailed numerical experiment.

Effects of Bleed Flow on Heat/Mass Transfer in a Rotating Rib-Roughened Channel

2006 ◽  
Vol 129 (3) ◽  
pp. 636-642 ◽  
Author(s):  
Yun Heung Jeon ◽  
Suk Hwan Park ◽  
Kyung Min Kim ◽  
Dong Hyun Lee ◽  
Hyung Hee Cho
Keyword(s):  
Mass Transfer ◽  
Heat Mass Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Hydraulic Diameter ◽  
Transfer Coefficients ◽  
Square Channel ◽  
Rib Turbulators ◽  
Sublimation Method

The present study investigates the effects of bleed flow on heat/mass transfer and pressure drop in a rotating channel with transverse rib turbulators. The hydraulic diameter (Dh) of the square channel is 40.0mm. 20 bleed holes are midway between the rib turburators on the leading surface and the hole diameter (d) is 4.5mm. The square rib turbulators are installed on both leading and trailing surfaces. The rib-to-rib pitch (p) is 10.0 times of the rib height (e) and the rib height-to-hydraulic diameter ratio (e∕Dh) is 0.055. The tests were conducted at various rotation numbers (0, 0.2, 0.4), while the Reynolds number and the rate of bleed flow to main flow were fixed at 10,000 and 10%, respectively. A naphthalene sublimation method was employed to determine the detailed local heat transfer coefficients using the heat/mass transfer analogy. The results suggest that for a rotating ribbed passage with the bleed flow of BR=0.1, the heat/mass transfer on the leading surface is dominantly affected by rib turbulators and the secondary flow induced by rotation rather than bleed flow. The heat/mass transfer on the trailing surface decreases due to the diminution of main flow. The results also show that the friction factor decreases with bleed flow.

scholarly journals Modern approaches to the intensification of heat and mass exchange in multi-temperature condensation filters

2021 ◽  
Vol 2039 (1) ◽  
pp. 012018
Author(s):  
M V Malevany ◽  
D A Konovalov
Keyword(s):  
Mass Transfer ◽  
Heat Exchange ◽  
Heat And Mass Transfer ◽  
Liquid Flow ◽  
Mass Exchange ◽  
Single Phase ◽  
Heat And Mass Exchange ◽  
Analytical Review

Abstract The article considers the problems and features of heat and mass exchange on developed surfaces in the conditions of both single-phase and vapour-liquid flow during its condensation. We give a brief analytical review of studies of hydrodynamics and heat exchange in such systems. We analyzed the efficiency of the working channel of the condensation filter and identified problematic points. We offer possible methods for intensifying heat and mass transfer on working surfaces.

Sign in / Sign up

Export Citation Format

Share Document