scholarly journals Analysis of Vibroacoustic Modulations for Crack Detection: A Time-Frequency Approach Based on Zhao-Atlas-Marks Distribution

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
A. Trochidis ◽  
L. Hadjileontiadis ◽  
K. Zacharias

The vibro-acoustic modulation (VAM) technique is probably the most widely used nonlinear method for crack detection. The VAM method is based on the effect of modulation of high-frequency acoustic waves by a low-frequency vibration. The intensity of the modulation is related to the severity of the damage and has been used so far as a damage index. The damage index simply based on the amplitude of the first side bands in the spectral domain often leads to controversial results about the severity of the damage. In this work, the nonlinear characteristics of the vibro-modulation were systematically investigated by employing time-frequency analysis based on the Zhao-Atlas-Marks (ZAM) distribution. The results of the analysis show that the amplitude of the sideband components is modulated by the low frequency vibration and the modulation amplitude depends on the size of the crack. Based on the obtained results, a new damage index was defined in relation to the strength of the modulation. The new damage index is more sensitive and robust and correlates better with crack size compared to the index based on the amplitude of the sidebands.

2017 ◽  
Vol 17 (2) ◽  
pp. 218-226 ◽  
Author(s):  
Bin Liu ◽  
Zhiwei Luo ◽  
Tie Gang

The use of vibro-acoustic modulation is an effective nonlinear and nondestructive approach to the detection and monitoring of cracks in fatigued, defective, and fractured materials. However, the vibro-acoustic modulation results strongly depend on choice of the testing parameters. To implement this technique for additional applications, the effect of variation in the test parameters must be well understood. This study investigates the influence of variation in the amplitude and frequency of pumping (low-frequency vibration) signals on the modulation. We apply two kinds of probing excitations, sine-wave and swept-signal excitations, and we measure the modulation intensity variation with changes in the relevant parameters to observe their influence on the modulations. Dynamic strain measurement of the crack area is utilized to analyze the relation between the degree of crack opening/closing and the modulation on the crack interface. The results indicate that the probing amplitude has little effect on the modulation, and furthermore, the sweep-signal excitation technique can be used to select the proper probing frequency. The results also indicate that there is a critical pumping strain value ( εc) for the crack samples. When the pumping strain reaches this critical value, the modulation reaches a maximum. However, the opening/closing area cannot increase any more even if the pumping amplitude further increases, and thus, the modulation does not change. The extent of the crack opening/closing also varies with the pumping frequency. Our results suggest that increased sensitivity to crack detection can be achieved with the use of the resonance frequency as the pumping frequency in vibro-acoustic modulation tests.


SINERGI ◽  
2015 ◽  
Vol 19 (1) ◽  
pp. 1
Author(s):  
Gigih Priyandoko ◽  
Tan Siew Fun

This project discuss about the defect detection of plastic pipe by using nonlinear acoustic wave modulation method. Nonlinaer acoustic modulations are investigated for fatigue crack detection. It is a sensitive method for damage detection and it is based on the propagation of high frequency acoustic waves in plastic pipe with low frequency excitation. The plastic pipe is excited simultaneously with a slow amplitude modulated vibration pumping wave and a constant amplitude probing wave. The frequency of both the excitation signals coincides with the resonances of the plastic pipe. An actuator is used for frequencies generation while sensor is used for the frequencies detection. Besides that, a PVP pipe is used as the specimen as it is commonly used for the conveyance of liquid in many fields. The results obtained are being observed and the difference between uncrack specimen and cracked specimen can be distinguished.


2018 ◽  
Vol 18 (3) ◽  
pp. 920-933 ◽  
Author(s):  
Suyoung Yang ◽  
Sung-Youb Jung ◽  
Kiyoung Kim ◽  
Peipei Liu ◽  
Sangmin Lee ◽  
...  

In this study, a tunable electromagnetic energy harvesting system, consisting of an energy harvester and energy harvesting circuits, is developed for harnessing energy from low-frequency vibration (below 10 Hz) of a bridge, and the harvesting system is integrated with a wireless fatigue crack detection sensor. The uniqueness of the proposed energy harvesting system includes that (1) the resonance frequencies of the proposed energy harvester can be readily tuned to the resonance frequencies of a host structure, (2) an improved energy harvesting efficiency compared to other electromagnetic energy harvesters is achieved in low-frequency and vibration, and (3) high-efficiency energy harvesting circuits for rectification are developed. Furthermore, the developed energy harvesting system is integrated with an on-site wireless sensor deployed on Yeongjong Grand Bridge in South Korea for online fatigue crack detection. To the best knowledge of the authors, this is the very first study where a series of low-frequency vibration energy harvesting, rectification, and battery charging processes are demonstrated under a real field condition. The field test conducted on Yeongjong Grand Bridge, where fatigue cracks have become of a great concern, shows that the proposed energy harvester can generate a peak voltage of 2.27 V and a root mean square voltage of 0.21 V from 0.18-m/s2 root mean square acceleration at 3.05 Hz. It is estimated the proposed energy harvesting system can harness around 67.90 J for 3 weeks and an average power of 37.42 µW. The battery life of the wireless sensor is expected to extend from 1.5 to 2.2 years. The proposed energy harvesting circuits, composed of the AC–DC and boost-up converters, exhibit up to 50% battery charging efficiency when the voltage generated by the proposed energy harvester is 200 mV or higher. The proposed boost-up converter has a 100 times wider input power range than a conventional boost-up converter with a similar efficiency.


Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1336
Author(s):  
Wei Fan ◽  
Hong Lu ◽  
Yongquan Zhang ◽  
Xiangang Su

The dynamic vibration of the gear coupling-rotor system (GCRS) caused by misalignment is an important factor of low frequency vibration and noise radiation of the naval marine. The axial misalignment of gear coupling is inevitable owing to mass eccentricity, and is unconstrained in axial direction at high-speed operation. Therefore, the dynamic model of GCRS is proposed, considering gear-coupling misalignment and contact force in this paper. The whole motion differential equation of GCRS is established based on the finite element method. Moreover, the numerical calculation method of meshing force, considering the uniform distribution load on contact surface, is presented, and the mathematical predictive time–frequency characteristics are analyzed by the Newmark stepwise integral approach. Finally, a reduced-scale application of the propulsion shaft system is utilized to validate the effectiveness of the proposed dynamic model. For the sensibility to low-frequency vibration, the natural frequencies and vibration modes of GCRS are analyzed through the processing and analysis of acceleration signal. The experimental dynamic response and main components of vibration are respectively consistent with mathematical results, which demonstrate the effectiveness of the proposed dynamic model of GCRS with misalignment. Furthermore, it also shows that the proposed finite element analysis and calculation method are suitable for complex shafting, providing a novel thought for dynamic analysis of the propeller–shaft–hull coupled system of marine.


Geophysics ◽  
2007 ◽  
Vol 72 (1) ◽  
pp. V13-V20 ◽  
Author(s):  
Yanghua Wang

A seismic trace may be decomposed into a series of wavelets that match their time-frequency signature by using a matching pursuit algorithm, an iterative procedure of wavelet selection among a large and redundant dictionary. For reflection seismic signals, the Morlet wavelet may be employed, because it can represent quantitatively the energy attenuation and velocity dispersion of acoustic waves propagating through porous media. The efficiency of an adaptive wavelet selection is improved by making first a preliminary estimate and then a localized refining search, whereas complex-trace attributes and derived analytical expressions are also used in various stages. For a constituent wavelet, the scale is an important adaptive parameter that controls the width of wavelet in time and the bandwidth of the frequency spectrum. After matching pursuit decomposition, deleting wavelets with either very small or very large scale values can suppress spikes and sinusoid functions effectively from the time-frequency spectrum. This time-frequency spectrum may be used in turn for lithological analysis—for instance, detection of a gas reservoir. Investigation shows that the low-frequency shadow associated with a carbonate gas reservoir still exists, even high-frequency amplitudes are compensated by inverse-[Formula: see text] filtering.


2014 ◽  
Vol 13 (6) ◽  
pp. 660-670 ◽  
Author(s):  
Sungmin Kim ◽  
Douglas E Adams ◽  
Hoon Sohn ◽  
Gustavo Rodriguez-Rivera ◽  
Noah Myrent ◽  
...  

This article presents a new technique for identifying cracks in wind turbine blades undergoing operational loads using the Vibro-Acoustic Modulation technique. Vibro-Acoustic Modulation utilizes a low-frequency pumping excitation signal in conjunction with a high-frequency probing excitation signal to create the modulation that is used to identify cracks. Wind turbines provide the ideal conditions in which Vibro-Acoustic Modulation can be utilized because wind turbines experience large low-frequency structural vibrations during operation which can serve as the low-frequency pumping excitation signal. In this article, the theory for the vibro-acoustic technique is described, and the proposed crack detection technique is demonstrated with Vibro-Acoustic Modulation experiments performed on a small Whisper 100 wind turbine in operation. The experimental results are also compared with two other conventional vibro-acoustic techniques in order to validate the new technique. Finally, a computational study is demonstrated for choosing a proper probing signal with a finite element model of the cracked blade to maximize the sensitivity of the technique for detecting cracks.


2021 ◽  
Vol 12 (3) ◽  
pp. 452-458
Author(s):  
O. I. Dotsenko ◽  
А. М. Mischenko ◽  
G. V. Taradina

The early signs of vibration effects on the human body are microcirculation and transcapillary metabolism disorders, accompanied by disruption of the supply to and utilization of oxygen in the tissues and organs. However, there are few experimental studies aimed at finding targets of vibration in cells and determining the action mechanism of vibration. In in vitro experiments, human erythrocytes in buffer solution were exposed to low-frequency vibration (frequency range 8–32 Hz, amplitudes 0.5–0.9 mm) for 3 hours. The dynamics of the accumulation of membrane-bound catalase and hemoglobin and the distribution of ligand hemoglobin in the membrane-bound fraction were studied as the indicators of functional activity of cells. The choice of these indicators is justified by the participation of catalase and hemoglobin in O2-dependent cellular reactions as a part of protein complexes. Since pО2 is a trigger of conformational transitions in the hemoglobin molecule, simultaneously with oxygen transport, hemoglobin signals to different metabolic systems about oxygen conditions in the environment. The studies revealed that in the conditions of vibration, the activity of membrane-associated catalase increased by 40–50% in the frequency range of 12–24 Hz (amplitude 0.5 ± 0.04 mm), by 20–30% in the amplitude of 0.9 mm, but after about 100–120 min exposure the enzyme activity decreased even below the control level. There was a dose-dependent accumulation of membrane-bound hemoglobin during exposure to vibration. In the membrane-bound fraction of hemoglobin, oxyhemoglobin had the highest content (60–80%), while the content of methemoglobin varied 5–20%. During vibrations in the frequency range 12–28 Hz, 0.5 mm, we recorded 10–30% increase in oxyhemoglobin. With increase in the vibration amplitude (0.9 mm) in the frequency range of 16–32 Hz, constant content of oxyhemoglobin was noted at the beginning of the experiment, which tended to decrease during the last exposure time. Frequency of 32 Hz caused increase in the deoxyhemoglobin content in the membrane-bound fraction. The content of methemoglobin (metHb) in erythrocytes significantly increased during exposure to the frequency range of 12–24 Hz, with the amplitude of 0.5 mm (1.3–2.4 times). During the exposure to frequencies of 28 and 32 Hz, we observed the transition of methemoglobin to hemichrome. The content of methemoglobin in the cells was lower and decreased at the end of the experiment when the vibration amplitude was 0.9 mm. In these experimental conditions, no increase in hemichrome content in the membrane-bound fraction was recorded. Therefore, the degree of binding of catalase and hemoglobin with the membrane of erythrocytes that were exposed to vibration and the changes in the content of ligand forms in the composition of membrane-bound hemoglobin are dose-dependent. Low-frequency vibration initiates O2-dependent processes in erythrocytes. Targets of such an influence are nanobubbles of dissolved air (babstons), retained on the surface of erythrocytes due to Coulomb interactions, capable of coagulation and increase in size under the action of vibration. At first, the consequences of these processes are increase in oxygen content in the surface of erythrocytes, and then decrease as a result of degassing. Thus, increase in oxygen content on the surface initiates redox reactions, whereas decrease in oxygen content leads to reconstruction of metabolic processes oriented at overcoming hypoxia.


2017 ◽  
Vol 17 (3) ◽  
pp. 565-576 ◽  
Author(s):  
Kajetan Dziedziech ◽  
Lukasz Pieczonka ◽  
Maciej Adamczyk ◽  
Andrzej Klepka ◽  
Wieslaw J Staszewski

In this article, the non-linear vibro-acoustic modulation technique is used for structural damage detection. A new experimental configuration and data processing strategy are proposed to improve the damage detection capability of the technique. The swept sine chirp excitation is used for both low-frequency vibration/modal and high-frequency ultrasonic excitations. The adaptive resampling procedure is then applied to extract information about modulation intensity that relates to damage. The proposed method is illustrated using numerical simulations and experimental tests. The latter involves crack detection in an aluminium beam. The results of the proposed method are compared with the classical approach based on single harmonic excitation, demonstrating that similar damage detection information can be extracted. However, the major advantage of the proposed method is simplicity and robustness since no a priori selection of excitation frequencies is needed. As a result, crack detection is more reliable and unambiguous.


Author(s):  
K. Hama

The lateral line organs of the sea eel consist of canal and pit organs which are different in function. The former is a low frequency vibration detector whereas the latter functions as an ion receptor as well as a mechano receptor.The fine structure of the sensory epithelia of both organs were studied by means of ordinary transmission electron microscope, high voltage electron microscope and of surface scanning electron microscope.The sensory cells of the canal organ are polarized in front-caudal direction and those of the pit organ are polarized in dorso-ventral direction. The sensory epithelia of both organs have thinner surface coats compared to the surrounding ordinary epithelial cells, which have very thick fuzzy coatings on the apical surface.


Sign in / Sign up

Export Citation Format

Share Document