scholarly journals The Effect of Nanofluid Volume Concentration on Heat Transfer and Friction Factor inside a Horizontal Tube

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Adnan M. Hussein ◽  
K. V. Sharma ◽  
R. A. Bakar ◽  
K. Kadirgama
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Thermal Properties ◽  
Friction Factor ◽  
Volume Concentration ◽  
Convection Heat Transfer ◽  
Horizontal Tube ◽  
Maximum Deviation ◽  
Flat Tube

The additives of solid nanoparticles to liquids are significant enhancement of heat transfer and hydrodynamic flow. In this study, the thermal properties of three types of nanoparticles (Al2O3, TiO2, and SiO2) dispersed in water as a base fluid were measured experimentally. Forced convection heat transfer turbulent flow inside heated flat tube was numerically simulated. The heat flux around flat tube is 5000 W/m2and Reynolds number is in the range of5×103to50×103. CFD model by finite volume method used commercial software to find hydrodynamic and heat transfer coefficient. Simulation study concluded that the thermal properties measured and Reynolds number as input and friction factor and Nusselt number as output parameters. Data measured showed that thermal conductivity and viscosity increase with increasing the volume concentration of nanofluids with maximum deviation 19% and 6%, respectively. Simulation results concluded that the friction factor and Nusselt number increase with increasing the volume concentration. On the other hand, the flat tube enhances heat transfer and decreases pressure drop by 6% and −4%, respectively, as compared with circular tube. Comparison of numerical analysis with experimental data available showed good agreement with deviation not more than 2%.

A Numerical Simulation of Heat Transfer Enhancement Using Al2O3 Nanofluid

2020 ◽  
Vol 10 (5) ◽  
pp. 610-621
Author(s):  
Taliv Hussain ◽  
Mohammad T. Javed
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Volume Concentration ◽  
Numerical Study ◽  
Pure Water ◽  
Maximum Deviation ◽  
Nanoparticle Concentration ◽  
Maximum Increase

Introduction: A numerical study is performed in which the friction factor and forced convection heat transfer is studied for Al2O3 nanoparticle dispersed in water as a base fluid. Methods: Four concentrations of nanofluids in the range of 0-2.5 vol% have been simulated. The Reynolds Number is varied in the range of 100-500 by varying inlet velocity. Cross flow of air is assumed over the pipe with air velocity of 2.2 m/s. Results: The results depict that the friction factor decreases with an increase in flow rate and increases with increase in volume concentration. The maximum deviation for friction factor obtained by simulation from that obtained using Darcy’s relation is about 21.5% for water. Nusselt number increases with increase in Reynolds Number and nanofluid volume concentration with a maximum of 7653.68 W/m2 at a nanoparticle concentration of 2.5% and Reynolds Number of 500. Heat transfer rate enhancement of upto 13.6% is obtained as compared to pure water. The maximum increase in Nusselt Number is about 13.07% for a nanoparticle concentration of 2.5%. Conclusion: The simulation results are compared with established relations obtained by other researchers and there is a good agreement in terms of trends obtained. The deviations from established relations are also depicted.

scholarly journals 3D Numerical simulation of turbulent heat transfer and Fe3O4/nanofluid annular flow in sudden enlargement

2021 ◽  
Vol 321 ◽  
pp. 04014
Author(s):  
Hussein Togun
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transport ◽  
Annular Flow ◽  
Volume Concentration ◽  
Convection Heat Transfer ◽  
Turbulent Heat Transfer ◽  
Recirculation Region ◽  
Convection Heat

In this paper, 3D Simulation of turbulent Fe3O4/Nanofluid annular flow and heat transfer in sudden expansion are presented. k-ε turbulence standard model and FVM are applied with Reynolds number different from 20000 to 50000, enlargement ratio (ER) varied 1.25, 1.67, and 2, , and volume concentration of Fe3O4/Nanofluid ranging from 0 to 2% at constant heat flux of 4000 W/m2. The main significant effect on surface Nusselt number found by increases in volume concentration of Fe3O4/Nanofluid for all cases because of nanoparticles heat transport in normal fluid as produced increases in convection heat transfer. Also the results showed that suddenly increment in Nusselt number happened after the abrupt enlargement and reach to maximum value then reduction to the exit passage flow due to recirculation flow as created. Moreover the size of recirculation region enlarged with the rise in enlargement ratio and Reynolds number. Increase of volume Fe3O4/nanofluid enhances the Nusselt number due to nanoparticles heat transport in base fluid which raises the convection heat transfer. Increase of Reynolds number was observed with increased Nusselt number and maximum thermal performance was found with enlargement ratio of (ER=2) and 2% of volume concentration of Fe3O4/nanofluid. Further increases in Reynolds number and enlargement ratio found lead to reductions in static pressure.

Pressure Drop and Heat Transfer of Nanofluid in Turbulent Pipe Flow Considering Particle Coagulation and Breakage

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Jian-Zhong Lin ◽  
Yi Xia ◽  
Xiao-Ke Ku
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Pipe Flow ◽  
Volume Concentration ◽  
Particle Diameter ◽  
Turbulent Pipe Flow ◽  
Particle Volume ◽  
Friction Factors

Numerical simulations of Al2O3/water nanofluid in turbulent pipe flow are performed with considering the particle convection, diffusion, coagulation, and breakage. The distributions of particle volume concentration, the friction factor, and heat transfer characteristics are obtained. The results show that the initial uniform distributions of particle volume concentration become nonuniform, and increase from the pipe wall to the center. The nonuniformity becomes significant along the flow direction from the entrance and attains a steady state gradually. Friction factors increase with the increase of particle volume concentrations and particle diameter, and with the decrease of Reynolds number. The friction factors increase remarkably at lower volume concentration, while slightly at higher volume concentration. The presence of nanoparticles provides higher heat transfer than pure water. The Nusselt number of nanofluids increases with increasing Reynolds number, particle volume concentration, and particle diameter. The rate increase in Nusselt number at lower particle volume concentration is more than that at higher concentration. For a fixed particle volume concentration, the friction factor is smaller while the Nusselt number is larger for the case with uniform distribution of particle volume concentration than that with nonuniform distribution. In order to effectively enhance the heat transfer using nanofluid and simultaneously save energy, it is necessary to make the particle distribution more uniform. Finally, the expressions of friction factor and Nusselt number as a function of particle volume concentration, particle diameter and Reynolds number are derived based on the numerical data.

Heat Transfer Investigation of a Tube Partially Wrapped by Metal Porous Layer as a Potential Novel Tube for Air Cooled Heat Exchangers

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. Mohammadpour-Ghadikolaie ◽  
M. Saffar-Avval ◽  
Z. Mansoori ◽  
N. Alvandifar ◽  
N. Rahmati
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Porous Layer ◽  
Transfer Rate ◽  
Metal Foam ◽  
Convection Heat Transfer ◽  
Darcy Number ◽  
High Heat Transfer

Laminar forced convection heat transfer from a constant temperature tube wrapped fully or partially by a metal porous layer and subjected to a uniform air cross-flow is studied numerically. The main aim of this study is to consider the thermal performance of some innovative arrangements in which only certain parts of the tube are covered by metal foam. The combination of Navier–Stokes and Darcy–Brinkman–Forchheimer equations is applied to evaluate the flow field. Governing equations are solved using the finite volume SIMPLEC algorithm and the effects of key parameters such as Reynolds number, metal foam thermophysical properties, and porous layer thickness on the Nusselt number are investigated. The results show that using a tube which is fully wrapped by an external porous layer with high thermal conductivity, high Darcy number, and low drag coefficient, can provide a high heat transfer rate in the high Reynolds number laminar flow, increasing the Nusselt number almost as high as 16 times compared to a bare tube. The most important result of thisstudy is that by using some novel arrangements in which the tube is partially covered by the foam layer, the heat transfer rate can be increased at least 20% in comparison to the fully wrapped tube, while the weight and material usage can be considerably reduced.

A Comparative Study of Performance of Low Reynolds Number Turbulence Models for Various Heat Transfer Enhancement Simulations

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Ankit Tiwari ◽  
Savas Yavuzkurt
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Enhancement ◽  
Friction Factor ◽  
Fluid Dynamic ◽  
Low Reynolds Number ◽  
Turbulence Models ◽  
Transfer Enhancement ◽  
Low Reynolds

The goal of this study is to evaluate the computational fluid dynamic (CFD) predictions of friction factor and Nusselt number from six different low Reynolds number k–ε (LRKE) models namely Chang–Hsieh–Chen (CHC), Launder–Sharma (LS), Abid, Lam–Bremhorst (LB), Yang–Shih (YS), and Abe–Kondoh–Nagano (AKN) for various heat transfer enhancement applications. Standard and realizable k–ε (RKE) models with enhanced wall treatment (EWT) were also studied. CFD predictions of Nusselt number, Stanton number, and friction factor were compared with experimental data from literature. Various parameters such as effect of type of mesh element and grid resolution were also studied. It is recommended that a model, which predicts reasonably accurate values for both friction factor and Nusselt number, should be chosen over disparate models, which may predict either of these quantities more accurately. This is based on the performance evaluation criterion developed by Webb and Kim (2006, Principles of Enhanced Heat Transfer, 2nd ed., Taylor and Francis Group, pp. 1–72) for heat transfer enhancement. It was found that all LRKE models failed to predict friction factor and Nusselt number accurately (within 30%) for transverse rectangular ribs, whereas standard and RKE with EWT predicted friction factor and Nusselt number within 25%. Conversely, for transverse grooves, AKN, AKN/CHC, and LS (with modified constants) models accurately predicted (within 30%) both friction factor and Nusselt number for rectangular, circular, and trapezoidal grooves, respectively. In these cases, standard and RKE predictions were inaccurate and inconsistent. For longitudinal fins, Standard/RKE model, AKN, LS and Abid LRKE models gave the friction factor and Nusselt number predictions within 25%, with the AKN model being the most accurate.

Heat Transfer by Mixed Convection Opposing Laminar Flow From the Inside Surface of Uniformly Heated Inclined Circular Tube

2006 ◽  
Author(s):  
H. Mohammed ◽  
T. Yusaf
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Flow Direction ◽  
Convection Heat Transfer ◽  
Heat Transfer Process ◽  
Secondary Flows ◽  
Opposed Flow ◽  
Wide Range

This paper aims to investigate the effect of the flow pattern on the mixed convection heat transfer. A 28 thermocouples wire were installed along a 900mm copper tube to measure the temperature distribution. Three insulation layers of fiber glass, asbestos and gypsum were used to minimize to heat lost to the surrounding. A forced convection at the entrance region of a fully developed opposing laminar air flow was investigated to evaluate the flow direction effect on the Nusselt number. The investigation covered a wide range of Reynolds number from 410 to 1600 and heat flux varied from 63W/m2 to 1260W/m2, with different angles of tube inclination of 30°, 45°, 60°, and 90°. It was found that the surface temperature variation along the tube for opposed flow higher than the assisted flow but lower than the horizontal orientation. The Reynolds number has a significant effect on Nusselt number in opposed flow while the effect of Reynolds number was found to be small in the case of assisted flow. The Nusselt number values were lower for opposed flow than the assisted flow. The temperature profiles results have revealed that the secondary flows created by natural convection have a significant effect on the heat transfer process. The obtained average Nusselt number values were correlated by dimensionless groups as Log Nu against Log Ra/Re.

scholarly journals Graphing Behaviour of Heat Transfer In Terms of Nusselt and Reynolds

2021 ◽  
Vol 6 (2) ◽  
pp. 41-52
Author(s):  
Mohd Rahimie Md Noor ◽  
Nur Syafiqah Hidayah Mohd Fauzi ◽  
Siti Nur Fadhilah Masrom ◽  
Mohd Azry Abdul Malek ◽  
Muhammad Firdaus Mustapha ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Volume Flow Rate ◽  
Convection Heat Transfer ◽  
Heat Transfer Process ◽  
Two Fluids ◽  
The Relationship

Heat exchangers are tools used to transfer thermal energy between two fluids (liquid or gas) by convection and conduction at different level of temperatures. Heat exchangers are the common equipment and employed in many different applications because of ability to withstand high temperatures and compactness. There are no intermixing or leakage occurred between two fluids during the heat transfer process as fluids are separated by walls of heat exchanger. The main objective of this project is to determine the heat exchanger effectiveness in heat transfer performance. This will be done by investigating the performance of five different angles of heat exchanger which are 150,300, 450, 600 and 750. The effectiveness of heat exchanger depends on the convection heat transfer coefficient of the fluid. Besides that, this project also aims to develop some parameters such as Nusselt number, Reynolds number and Prandtl number for evaluating the heat transfer. It is found that the Nusselt Number at angle of 150 is lower compared to angle of 750. Meanwhile, Reynolds number for angle 150 is higher than angle 750 which means that the type of flow produced by angle 150 is turbulent flow while for 750 angle is laminar flow. Hence, the overall result of this project proved that 150 is the best angle for heat exchanger in chimney because of higher velocity, higher volume flow rate, higher density of gas and higher LMTD. The relationship between Nusselt number and Reynolds number between different angles can be observed by plotting the graph using Maple Software.

scholarly journals Numerical Simulation of the Performance of Applying Different Nanofluids in a Tube with a 90° Bend at the Center of the Tube

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Dinesh Kumar ◽  
Gurpreet Singh Sokhal ◽  
Nima Khalilpoor ◽  
AlibekIssakhov ◽  
Babak Mosavati
Keyword(s):  
Heat Transfer ◽  
Carbon Nanotubes ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Aluminum Oxide ◽  
Copper Oxide ◽  
Transfer Coefficient ◽  
Volume Concentration ◽  
Multiwalled Carbon ◽  
Flat Tube

This research manuscript addresses the study of the performance of a flat tube having a 90° bend under the flow of three different nanofluids such as copper oxide, multiwalled carbon nanotubes, and aluminum oxide/water nanofluids at different inlet fluid temperatures and Reynolds numbers. The performance of the flat tube is analyzed under the Reynolds number between 5000 and 11000 and a fluid inlet temperature range of 35°C–50°C. The results obtained in this study show that the heat transfer coefficient increases with the increase in volume concentration as well as Reynolds number. The maximum heat transfer coefficient is obtained using multiwalled carbon nanotubes followed by copper oxide and then aluminum oxide. This study also illustrates that the friction factor increases with the increase in volume concentration and decrease in Reynolds number. The results of the numerical study have been validated with the help of an experimental study. The study has proved that the use of nanofluids instead of the conventional fluid can lead to reducing the size of the tube for the same amount of heat transfer which can prove the reduction of the size in heat transfer equipment. Furthermore, it is also observed in this study that the presence of the 90° bend in the flat tube improved the heat transfer performance due to the increased turbulence at the bent section of the tube.

scholarly journals CFD Analysis on the Heat Transfer and Fluid Flow of Solar Air Heater having Transverse Triangular Block at the Bottom of Air Duct

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1099
Author(s):  
Hwi-Ung Choi ◽  
Kwang-Hwan Choi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Design Parameters ◽  
Solar Air Heater ◽  
Air Heater ◽  
Geometric Conditions ◽  
Computational Fluid Dynamics Analysis ◽  
Triangular Block

In this study, a two-dimensional CFD (computational fluid dynamics) analysis was performed to investigate the heat-transfer and fluid-friction characteristics in a solar air heater having a transverse triangular block at the bottom of the air duct. The Reynolds number, block height (e), pitch (P), and length (l) were chosen as design parameters. The results are validated by comparing the Nusselt number predicted by simulation with available experimental results. Renormalization-group (RNG) k - ε model with enhanced wall-treatment was selected as the most appropriate turbulence model. From the results, it was found that the presence of a transverse triangular block produces a higher Nusselt number than that of smooth air duct. The enhancement in Nusselt number varied from 1.19 to 3.37, according to the geometric conditions investigated. However, the use of transverse triangular block also results in significantly higher friction losses. The thermohydraulic performance (THPP) was also estimated and has a maximum value of 1.001 for height (e) of 20 mm, length (l) of 120 mm, and pitch (P) of 150 mm, at Reynolds number of 8000. Furthermore, in the present study, correlations of the Nusselt number and friction factor were developed as a function of geometrical conditions of the transverse triangular block and Reynolds number, which can be used to predict the value of Nusselt number and friction factor with the absolute percentage deviations of 3.29% and 7.92%, respectively.

scholarly journals Effect of Pin Diameter Degressive Gradient on Heat Transfer in a Microreactor with Non-Uniform Pin-Fin Array under Low Reynolds Number Conditions

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2702
Author(s):  
Miao Qian ◽  
Jie Li ◽  
Zhong Xiang ◽  
Chao Yan ◽  
Xudong Hu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Low Reynolds Number ◽  
Hydrodynamic Characteristics ◽  
Pin Fin ◽  
Low Reynolds ◽  
Pin Fin Array

To improve the efficiency of hydrogen-producing microreactors with non-uniform pin-fin array, the influence of the pin diameter degressive gradient of the non-uniform pin-fin array (NPFA) on heat transfer and pressure drop characteristics is analyzed in this study via numerical simulation under low Reynolds number conditions. Because correlations in prior studies cannot be used to predict the Nusselt number and pressure drop in the NPFA, new heat transfer and friction factor correlations are developed in this paper to account for the effect of the pin diameter degressive gradient, providing a method for the optimized design of the pin diameter degressive gradient for a microreactor with NPFA. The results show that the Nusselt number and friction factor under a low Reynolds number are quite sensitive to the pin diameter degressive gradient. Based on the new correlations, the exponents of the pin diameter degressive gradient for the friction factor and Nusselt number were 6.9 and 2.1, respectively, indicating the significant influence of the pin diameter degressive gradient on the thermal and hydrodynamic characteristics in the NPFA structure.

Sign in / Sign up

Export Citation Format

Share Document