scholarly journals Evaluate the Impact of Cold Wave on Face Slab Cracking Using Fuzzy Finite Element Method

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Dongjian Zheng ◽  
Lin Cheng ◽  
Yanxin Xu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Temperature Drop ◽  
Extension Principle ◽  
Cold Wave ◽  
Prevention Measures ◽  
Fuzzy Variables ◽  
Fuzzy Finite Element ◽  
The Impact ◽  
Element Method

We use fuzzy finite element method (FEM) to analyze the impact of cold wave on face slab cracking of a concrete-faced rockfill dam (CFRD). The static response of dam and the temperature field of face slab are calculated using deterministic FEM since some observed and test data can be obtained. Some parameters of Goodman contact element between face slabs and cushion material are selected as fuzzy variables, and the fuzzy FEM is used to calculate fuzzy stress of face slab. The fuzzy FEM is implemented using vertex method based on the extension principle. Through the analysis of two selected calculation cases of cold wave, it is shown that the calculated cracking direction and cracking zone caused by thermal stress are similar to those of the observed cracks. This proves that the cold wave that caused swift air temperature drop is an important reason for the cracking of face slab. According to these analysis results, some cracking prevention measures are then proposed.

A Fracture Mechanics Based Parametric Study of the Copper-to-Copper Direct Thermo-Compression Bonded Interface Using Finite Element Method

2013 ◽  
Author(s):  
Ah-Young Park ◽  
Satish Chaparala ◽  
Seungbae Park
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Parametric Study ◽  
Initial Crack ◽  
Bonding Interface ◽  
Interface Condition ◽  
Large Temperature ◽  
Bonded Interface ◽  
The Impact ◽  
Element Method

Through-silicon via (TSV) technology is expected to overcome the limitations of I/O density and helps in enhancing system performance of conventional flip chip packages. One of the challenges for producing reliable TSV packages is the stacking and joining of thin wafers or dies. In the case of the conventional solder interconnections, many reliability issues arise at the interface between solder and copper bump. As an alternative solution, Cu-Cu direct thermo-compression bonding (CuDB) is a possible option to enable three-dimension (3D) package integration. CuDB has several advantages over the solder based micro bump joining, such as reduction in soldering process steps, enabling higher interconnect density, enhanced thermal conductivity and decreased concerns about intermetallic compounds (IMC) formation. Critical issue of CuDB is bonding interface condition. After the bonding process, Cu-Cu direct bonding interface is obtained. However, several researchers have reported small voids at the bonded interface. These defects can act as an initial crack which may lead to eventual fracture of the interface. The fracture could happen due to the thermal expansion coefficient (CTE) mismatch between the substrate and the chip during the postbonding process, board level reflow or thermal cycling with large temperature changes. In this study, a quantitative assessment of the energy release rate has been made at the CuDB interface during temperature change finite element method (FEM). A parametric study is conducted to analyze the impact of the initial crack location and the material properties of surrounding materials. Finally, design recommendations are provided to minimize the probability of interfacial delamination in CuDB.

scholarly journals New CZM for Interfacial Crack Growth

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Huifen Peng ◽  
Yujie Song ◽  
Ye Xia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Crack Growth ◽  
Interface Crack ◽  
Interfacial Crack ◽  
Structure Design ◽  
Zone Model ◽  
Simulation Results ◽  
The Impact ◽  
Element Method

The cohesive zone model (CZM) has been widely used for numerical simulations of interface crack growth. However, geometrical and material discontinuities decrease the accuracy and efficiency of the CZM when based on the conventional finite element method (CFEM). In order to promote the development of numerical simulation of interfacial crack growth, a new CZM, based on the wavelet finite element method (WFEM), is presented. Some fundamental issues regarding CZM of interface crack growth of double cantilever beam (DCB) testing were studied. The simulation results were compared with the experimental and simulation results of CFEM. It was found that the new CZM had higher accuracy and efficiency in the simulation of interface crack growth. At last, the impact of crack initiation length and elastic constants of material on interface crack growth was studied based on the new CZM. These results provided a basis for reasonable structure design of composite material in engineering.

Performance Evaluation of Spring for the Vehicle Suspension System Using the Nonlinear Finite Element Method

2014 ◽  
Vol 635-637 ◽  
pp. 594-597
Author(s):  
Byeong Soo Kim ◽  
Byung Young Moon ◽  
Sung Kwan Kim
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Composite Material ◽  
Suspension System ◽  
Nonlinear Finite Element ◽  
Nonlinear Finite Element Method ◽  
Air Spring ◽  
Rubber Sleeve ◽  
The Impact ◽  
Element Method

Air spring is used for the suspension system and it affects the vehicle stability and riding comfort by improving the impact-relief, braking, and cornering performance. Air Spring is comprised of the upper plate, lower plate, and rubber sleeve. Rubber sleeve is the composite material, which is made up of combination of rubber and Nylon, and the characteristics are changed according to the shape of rubber-sleeve, the angle of reinforcement cord. In this study, the distribution of internal stresses and the deformation of rubber composite material are analyzed through the nonlinear finite element method. The result showed that the internal maximum stresses and deformations about the changes of cord angle caused the more the Young's modulus decrease, the more maximum stress reduced.

Mathematical Simulation of Rigid Pile Composite Foundation with Lateral Unloading

2013 ◽  
Vol 368-370 ◽  
pp. 756-759
Author(s):  
Jing Ma ◽  
Wen Sheng Chen ◽  
Xue Feng Hu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Mathematical Simulation ◽  
Horizontal Displacement ◽  
Composite Foundation ◽  
The Finite Element Method ◽  
Rigid Pile ◽  
Rigid Pile Composite Foundation ◽  
The Impact ◽  
Element Method

Based on the Finite Element Method ,a model has been built to study the impact of rigid pile composite foundation with lateral unloading,then obtained a conclusion about the horizontal displacement during excavating.

Structural Reliability Analysis Using Fuzzy Finite Element Method

2013 ◽  
Vol 471 ◽  
pp. 306-312 ◽  
Author(s):  
A.Y.N. Yusmye ◽  
B.Y. Goh ◽  
A.K. Ariffin
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Reliability Analysis ◽  
Structural Reliability ◽  
Classical Method ◽  
Practical Method ◽  
Main Role ◽  
Structural Reliability Analysis ◽  
Fuzzy Finite Element ◽  
Element Method

The main requirement in designing a structure is to ensure the structure is reliable enough to withstand loading and the reliability study of structure. Classical and probability approach was introduced to analyse structural reliability. However, the approaches stated above are unable to take into account and counter the uncertainties arising from the natural of geometry, material properties and loading. This leads to the reduction in accuracy of the result. The goal of this study is to assess and determine the reliability of structures by taking into consideration of the epistemic uncertainties involved. Since it is crucial to develop an effective approach to model the epistemic uncertainties, the fuzzy set theory is proposed to deal with this problem. The fuzzy finite element method (FFEM) reliability analysis conducted has shown this method produces more conservative results compared to the deterministic and classical method espacially when dealing with problems which have uncertainties in input parameters. In conclusion, fuzzy reliability analysis is a more suitable and practical method when dealing with structural reliability with epistemic uncertainties in structural reliability analysis and FFEM plays a main role in determining the structural reliability in reality.

scholarly journals Optimization Procedure of Roller Elements Geometry with Regard to Durability of Spherical Roller Bearings

2020 ◽  
Vol 22 (2) ◽  
pp. 68-72
Author(s):  
Jan Steininger ◽  
Stefan Medvecky ◽  
Robert Kohar ◽  
Tomas Capak
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Roller Bearing ◽  
Optimization Procedure ◽  
Parametric Models ◽  
The Finite Element Method ◽  
Roller Bearings ◽  
Contact Points ◽  
The Impact ◽  
Element Method

The article deals with an optimization procedure of roller elements geometry with regard to durability of spherical roller bearings. The aim of the article is to examine the impact of change of the roller elements inner geometry on durability and reliability of spherical roller bearings; the contact strain along a spherical roller by means of the Finite Element Method at contact points of components of a spherical roller bearing by means of designed 3D parametric models. The most appropriate shape of roller elements inner geometry of a bearing from the standpoint of calculated durability was determined based on results of the contact analyses.

scholarly journals Numerical modelling of hydraulically bonded mixture with rubber admixture due to applied mechanical loadings

2017 ◽  
Vol 16 (3) ◽  
pp. 095-102
Author(s):  
Daniel Pietras ◽  
Tomasz Sadowski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Numerical Model ◽  
Fracture Energy ◽  
Extended Finite Element Method ◽  
Extended Finite Element ◽  
Anticipate Change ◽  
Transmission Zone ◽  
The Impact ◽  
Element Method

In this paper the application of the Extended Finite Element Method (XFEM) to anticipate change of the behaviour of composite with complex internal structure after use of the admixtures was presented. The response to mechanical loadings of bent beams made of hydraulically bonded mixture with rubber admixture was considered. The impact of the rubber granulate on the value of fracture energy was analysed. Moreover, the influence of an interfacial transmission zone quality on the achieved effect was assessed. Calculations were conducted by means of the muli-scale numerical model which was built in ABAQUS finite element method environment. The results derived indicate beneficial effect of rubber granulate on fracture energy of hydraulically bonded mixture.

Sign in / Sign up

Export Citation Format

Share Document