scholarly journals Electrodeposition of Oriented Cerium Oxide Films

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Adele Qi Wang ◽  
Teresa D. Golden
Keyword(s):  
Crystallite Size ◽  
Cerium Oxide ◽  
Oxide Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Crystallite Sizes ◽  
Bidentate Complex ◽  
20 Nm ◽  
Deposited Films ◽  
Deposition Conditions

Cerium oxide films of preferred orientation are electrodeposited under anodic conditions. A complexing ligand, acetate, was used to stabilize the cerium (III) ion in solution for deposition of the thin films. Fourier transform infrared spectroscopy showed that the ligand and metal tended to bind as a weakly bidentate complex. The crystallite size of the films was in the nanometer range as shown by Raman spectroscopy and was calculated from X-ray diffraction data. Crystallite sizes from 6 to 20 nm were obtained under the anodic deposition conditions. Sintering of the (111) oriented films showed an increase in the (111) orientation with temperatures up to 900°C. Also, the crystallite size increased from 20 nm to 120 nm under sintering conditions. Addition of the deposited films to the substrate improved corrosion resistance for the substrate.

X-ray diffraction Warren–Averbach mullite analysis in whiteware porcelains: influence of kaolin raw material

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 471-485 ◽  
Author(s):  
Angel Sanz ◽  
Joaquín Bastida ◽  
Angel Caballero ◽  
Marek Kojdecki
Keyword(s):  
Crystallite Size ◽  
Firing Temperature ◽  
Microstructural Analysis ◽  
Stoichiometric Composition ◽  
Raw Material ◽  
Size Distributions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Crystallite Sizes

ABSTRACTCompositional and microstructural analysis of mullites in porcelain whitewares obtained by the firing of two blends of identical triaxial composition using a kaolin B consisting of ‘higher-crystallinity’ kaolinite or a finer halloysitic kaolin M of lower crystal order was performed. No significant changes in the average Al2O3 contents (near the stoichiometric composition 3:2) of the mullites were observed. Fast and slow firing at the same temperature using B or M kaolin yielded different mullite contents. The Warren–Averbach method showed increase of the D110 mullite crystallite size and crystallite size distributions with small shifts to greater values with increasing firing temperature for the same type of firing (slow or fast) using the same kaolin, as well as significant differences between fast and slow firing of the same blend at different temperatures for each kaolin. The higher maximum frequency distribution of crystallite size observed at the same firing temperature using blends with M kaolin suggests a clearer crystallite growth of mullite in this blend. The agreement between thickening perpendicular to prism faces and mean crystallite sizes <D110> of mullite were not always observed because the direction perpendicular to 110 planes is not preferred for growth.

Dislocations, crystallite size, and planar faults in nanocrystalline ceria

2009 ◽  
Vol 24 (3) ◽  
pp. 228-233 ◽  
Author(s):  
S. R. Aghdaee ◽  
V. Soleimanian
Keyword(s):  
Grain Size ◽  
Dislocation Density ◽  
Crystallite Size ◽  
Cerium Oxide ◽  
Diffraction Line ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanocrystalline Ceria ◽  
Hall Plot

The modified Williamson–Hall and Warren–Averbach methods were used successfully for analyzing experimentally observed anisotropic X-ray diffraction line broadening and for determining reliable values of crystallite size and dislocation density in cerium oxide. The modified Williamson–Hall plot gives 22.3(2) nm for volume-weighted crystallite size, while the modified Warren–Averbach produces 18.0(2) nm for area-weighted grain size. The dislocation density and effective outer cut-off radius of dislocations obtained from the modified Warren–Averbach method are 1.8(3)×1015 m−2 and 15.5(1) nm, respectively.

Study of Nanocrystalline NiAl Alloys Prepared by Mechanical Alloying

2012 ◽  
Vol 329 ◽  
pp. 19-28 ◽  
Author(s):  
M. Gherib ◽  
A. Otmani ◽  
A. Djekoun ◽  
A. Bouasla ◽  
M. Poulain ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Crystallite Size ◽  
Milling Time ◽  
Structural Features ◽  
Milling Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Size Refinement ◽  
20 Nm ◽  
Kinetics Of

Nanostructured Powders of Ni-20wt%Al and Ni-50wt%Al Were Prepared, by Mechanical Alloying under an Argon Atmosphere, from Elemental Ni and Al Powders Using a Planetary Ball Mill (type Fritsch P7) for Different Times (0.5-24h).). Microstructural and Structural Features of the Final Products Were Characterized by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). the Results of the XRD Shows the Formation of the B2 (Ni Al) Phase after 2 Hours of Milling for both Systems. Also Detected Was the Ni3al Phase in Ni80al20after 4 Hours. Crystallite Size Refinement of the Final Product Occurred down to Nanometer Scales when the Milling Time Increased, and Attained 17 Nm in the Ni50al50System and 20 Nm in the other System, at 24 Hours. this Decrease in Crystallite Size Is Accompanied by an Increase in the Interval Level Strain. the Kinetics of Al Dissolution during the Milling Process of Ni50al50System Can Be Described by Two Regimes, Characterised by Different Values of Avrami Parameters which Are Calculated by Using the Johnson–Mehl–Avrami Formalism.

Applicability of Routine Methods of Crystallite Size Analysis*

1962 ◽  
Vol 6 ◽  
pp. 191-201
Author(s):  
Robert C. Rau
Keyword(s):  
Crystallite Size ◽  
Beryllium Oxide ◽  
Testing Procedure ◽  
Individual Performance ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Geometry ◽  
Crystallite Sizes ◽  
Performance Results

AbstractSeveral methods for the routine determination of crystallite size by means of X-ray diffraction line-broadening have previously been reported. Although these techniques have proven useful and reliable when utilized with the single X-ray diffractometer and instrumental geometry used to originally develop the methods, it was not known whether other instruments would provide similar reliability. Therefore a study was performed to evaluate the applicability of routine methods of crystallite size analysis to other X-ray diffraction units. A series of six beryllium oxide powder specimens, whose average crystallite sizes ranged stepwise from about 35 to nearly 3000 Å, were used to test a number of X-ray diffractometers. By using a predetermined diffraction geometry for each instrument tested, measured crystallite sizes were found to be quite reproducible and well within the limits of experimental error. The testing procedure, instrumental conditions, and individual performance results are presented in this paper.

A structural study of size-dependent lattice variation: In situ X-ray diffraction of the growth of goethite nanoparticles from 2-line ferrihydrite

2020 ◽  
Vol 105 (5) ◽  
pp. 652-663
Author(s):  
Peter J. Heaney ◽  
Matthew J. Oxman ◽  
Si Athena Chen
Keyword(s):  
Metal Oxides ◽  
Crystallite Size ◽  
Coefficient Of Thermal Expansion ◽  
Particle Growth ◽  
Rietveld Analysis ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Time Resolved ◽  
X Ray ◽  
Crystallite Sizes

Abstract Unlike most native metals, the unit cells of metal oxides tend to expand when crystallite sizes approach the nanoscale. Here we review different models that account for this behavior, and we present structural analyses for goethite (α-FeOOH) crystallites from ~10 to ~30 nm. The goethite was investigated during continuous particle growth via the hydrothermal transformation of 2-line ferrihydrite at pH 13.6 at 80, 90, and 100 °C using time-resolved, angle-dispersive synchrotron X-ray diffraction. Ferrihydrite gels were injected into polyimide capillaries with low background scattering, increasing the sensitivity for detecting diffraction from goethite nanocrystals that nucleated upon heating. Rietveld analysis enabled high-resolution extraction of crystallographic and kinetic data. Crystallite sizes for goethite increased with time at similar rates for all temperatures. With increasing crystallite size, goethite unit-cell volumes decreased, primarily as a result of contraction along the c-axis, the direction of closest-packing (space group Pnma). We introduce the coefficient of nanoscale contraction (CNC) as an analog to the coefficient of thermal expansion (CTE) to compare the dependence of lattice strain on crystallite size for goethite and other metal oxides, and we argue that nanoscale-induced crystallographic expansion is quantitatively similar to that produced when goethite is heated. In addition, our first-order kinetic model based on the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation yielded an activation energy for the transformation of ferrihydrite to goethite of 72.74 ± 0.2 kJ/mol, below reported values for hematite nucleation and growth.

Synthesis and Characterisation of Titania Nanotubes: Effect of Phase and Crystallite Size on Nanotube Formation

2007 ◽  
Vol 29-30 ◽  
pp. 211-214 ◽  
Author(s):  
D.L. Morgan ◽  
E.R. Waclawik ◽  
R.L Frost
Keyword(s):  
Raman Spectroscopy ◽  
Crystallite Size ◽  
Electron Spectroscopy ◽  
Driving Force ◽  
Titania Nanotubes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Material Type ◽  
Transmission Electron ◽  
Crystallite Sizes

Nanotubes were produced from commercial and self-prepared anatase and rutile which were treated with 7.5 M NaOH over a temperature range of 100 – 200°C in 20°C increments. The formation of nanotubes was examined as a function of starting material type and size. Products were characterised by X-Ray Diffraction (XRD), Transmission Electron Spectroscopy (TEM), and Raman Spectroscopy. The results indicated that both phase and crystallite size affected the nanotube formation. Rutile was observed to require a greater driving force than anatase to form nanotubes, and increases in crystallite sizes appeared to impede formation slightly.

The mean crystallite size within a hydrogenated nanocrystalline silicon based photovoltaic solar cell and its role in determining the corresponding crystalline volume fraction

2014 ◽  
Vol 92 (7/8) ◽  
pp. 857-861 ◽  
Author(s):  
K.J. Schmidt ◽  
Y. Lin ◽  
M. Beaudoin ◽  
G. Xia ◽  
S.K. O’Leary ◽  
...  
Keyword(s):  
Crystallite Size ◽  
Volume Fraction ◽  
Nanocrystalline Silicon ◽  
Crystalline Volume Fraction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Photovoltaic Solar Cell ◽  
Crystallite Sizes ◽  
The Mean ◽  
Silicon Based

We examine the dependence of the crystalline volume fraction on the mean crystallite size for hydrogenated nanocrystalline silicon based photovoltaic solar cells; this work builds upon an earlier study by Schmidt et al. (Mater. Res. Soc. Symp. Proc. 1536 (2013)). For each photovoltaic solar cell considered, the X-ray diffraction and Raman spectra are measured. Through the application of Scherrer’s equation, the X-ray diffraction results are used to determine the corresponding mean crystallite sizes. Through peak decomposition, the Raman results are used to estimate the corresponding crystalline volume fraction. Plotting the crystalline volume fraction as a function of the mean crystallite size, it is found that larger mean crystallite sizes tend to favor reduced crystalline volume fractions. The ability to randomly pack smaller crystallites with a greater packing fraction than their larger counterparts was suggested as a possible explanation for this observation.

Applications of X-ray Diffraction Crystallite Size/Strain Analysis to Seismosaurus Dinosaur Bone

1990 ◽  
Vol 34 ◽  
pp. 473-482 ◽  
Author(s):  
Steve J. Chipera ◽  
David L. Bish
Keyword(s):  
New Mexico ◽  
Crystallite Size ◽  
Profile Analysis ◽  
Rietveld Method ◽  
Strain Analysis ◽  
Morrison Formation ◽  
X Ray Diffraction ◽  
X Ray ◽  
A Minor ◽  
20 Nm

AbstractRecently, the remains of a giant Cretaceous Sauropod (~150 My old) were discovered in the Morrison Formation west of Albuquerque, New Mexico. This dinosaur, tentatively named Seismosaurus, was found in an exceptional state of preservation. Although it has been known since the 180Q's that fossilized bone is often composed of the mineral apatite, very few studies have been conducted to characterize farther the fossilized material. In an effort to gain insight into the state of preservation and Hie processes occurring in the bone since deposition, apatite in bone from Seismosaurus was compared with that from a contemporary elk from the Jemez Mountains, New Mexico, and with well-crystallized mineral apatite using X-ray powder diffraction and profile analysis techniques. Crystallite size/strain analyses were conducted using the Scherrer equation, the Warren-Averbaca and single-line methods, and the Rietveld method using the program GSAS. Heating the contemporary elk bone produced a decrease in the full-width-at-half-maximum (FWHM) of the reflections in the diffraction pattern. This decrease in FWHM is due to a decrease in microstrain along with a minor increase in crystallite size. Results from crystallite size/strain analysis show that both Seismosaurus and contemporary elk bone crystallites are elongate parallel to the c-axis. However, Seismosaurus bone crystallites are larger (-20-65 nm) with less strain than the contemporary elk bone crystallites (-8-20 nm), suggesting that if elk bone is an appropriate analog, then Seismosaurus bone must have undergone recrystallization.

Biocompatibility of Cerium Oxide Films Synthesized by Dual Plasma Deposition

2007 ◽  
Vol 330-332 ◽  
pp. 749-752
Author(s):  
Feng Juan Jing ◽  
Lu Wang ◽  
Y.W. Liu ◽  
J.Y. Cheng ◽  
Yong Xiang Leng ◽  
...  
Keyword(s):  
Cerium Oxide ◽  
Photoelectron Spectroscopy ◽  
Plasma Deposition ◽  
Oxide Films ◽  
Rare Earth Oxide ◽  
X Ray Diffraction ◽  
Good Adhesion ◽  
X Ray ◽  
Huvec Cells ◽  
Isotropic Carbon

Cerium oxide films have been fabricated using dual plasma deposition. X-ray diffraction. (XRD) reveals a crystalline phase and X-ray photoelectron spectroscopy (XPS) shows that La exists predominantly in the +4 oxidation state. The activated partial thromboplastin time is longer than that of blood plasma and stainless steel. Furthermore, the numbers of adhered, aggregated and morphologically changed platelets are reduced compared to low-temperature isotropic carbon (LTIC). HUVEC cells exhibit good adhesion and proliferation behavior on cerium oxide films. This study suggests rare earth oxide films are potential blood-contacting biomedical materials.

The Scherrer equation and the dynamical theory of X-ray diffraction

2016 ◽  
Vol 72 (3) ◽  
pp. 385-390 ◽  
Author(s):  
Francisco Tiago Leitão Muniz ◽  
Marcus Aurélio Ribeiro Miranda ◽  
Cássio Morilla dos Santos ◽  
José Marcos Sasaki
Keyword(s):  
Crystallite Size ◽  
Dynamical Theory ◽  
Polycrystalline Materials ◽  
X Ray Diffraction ◽  
Linear Absorption ◽  
X Ray ◽  
Crystallite Sizes ◽  
Scherrer Equation ◽  
High Degree ◽  
Kinematical Theory

The Scherrer equation is a widely used tool to determine the crystallite size of polycrystalline samples. However, it is not clear if one can apply it to large crystallite sizes because its derivation is based on the kinematical theory of X-ray diffraction. For large and perfect crystals, it is more appropriate to use the dynamical theory of X-ray diffraction. Because of the appearance of polycrystalline materials with a high degree of crystalline perfection and large sizes, it is the authors' belief that it is important to establish the crystallite size limit for which the Scherrer equation can be applied. In this work, the diffraction peak profiles are calculated using the dynamical theory of X-ray diffraction for several Bragg reflections and crystallite sizes for Si, LaB6and CeO2. The full width at half-maximum is then extracted and the crystallite size is computed using the Scherrer equation. It is shown that for crystals with linear absorption coefficients below 2117.3 cm−1the Scherrer equation is valid for crystallites with sizes up to 600 nm. It is also shown that as the size increases only the peaks at higher 2θ angles give good results, and if one uses peaks with 2θ > 60° the limit for use of the Scherrer equation would go up to 1 µm.

Sign in / Sign up

Export Citation Format

Share Document