scholarly journals Fluidization and Spouting of Fine Particles: A Comparison

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Pranati Sahoo ◽  
Abanti Sahoo
Keyword(s):  
Particle Size ◽  
Fine Particles ◽  
Particle Density ◽  
Spouted Bed ◽  
Dimensionless Analysis ◽  
Mathematical Expressions ◽  
Wide Range ◽  
Micron Particle ◽  
Bed Expansion ◽  
Fluidizing Medium

The fluidization characteristics of fine particles have been studied in both the fluidized bed and spouted bed. The effect of different system parameters (viz. static bed height, particle size, particle density and superficial velocity of the fluidizing medium, rotational speed of stirrer, and spout diameter) on the fluidization characteristics such as bed expansion/fluctuation ratios, bed pressure drop, minimum fluidizing/spouting velocity, and fluidization index of fine particles (around 60 micron particle size) have been analyzed. A stirrer/rod promoter has been used in the bed to improve the bed fluidity for fluidization process and spout diameter has been varied for spouted bed. Mathematical expressions for these bed dynamics have been developed on the basis of dimensionless analysis. Finally calculated values of these bed dynamics are compared with the experimentally observed values thereby indicating the successful applications of these developed correlations over a wide range of parameters.

Deposition of Trace Metals in Urban and Rural Areas in the Lake Michigan Basin

1993 ◽  
Vol 28 (3-5) ◽  
pp. 261-270 ◽  
Author(s):  
Nicola Pirrone ◽  
Gerald J. Keeler
Keyword(s):  
Particle Size ◽  
Trace Metals ◽  
Rural Area ◽  
Rural Areas ◽  
Lake Michigan ◽  
Fine Particles ◽  
Deposition Velocity ◽  
Fine Fraction ◽  
Coarse Fraction ◽  
Wide Range

Ambient concentrations measured in Chicago and in the rural area of Kankakee (Illinois) are presented for a wide range of trace metals associated with fine (<2.5 µm) and coarse (2.5-10 µm) particles. Elements typically of crustal origin in the fine fraction were detected at similar concentrations in both sites. However, crustal elements in the coarse fraction were found three to fifteen times higher than that associated with fine fraction in both sites. Elements primarily of anthropogenic origin were found in similar concentrations in Chicago and Kankakee, except for elements such as Cr which was detected at levels three to four times higher in Kankakee. Meteorological parameters, particle size distribution and surface characteristics are considered in a dynamic model for calculating the deposition velocity for each particle size. The deposition velocities for fine particles is in the range from 0.25 to 0.46 cm/s in Chicago and from 0.18 to 0.25 cm/s in Kankakee, while for coarse particles the range is from 1.47 to 2.93 cm/s in Chicago and from 0.87 to 1.71 cm/s in Kankakee. The deposition fluxes in Chicago are usually highest, except for Al which is deposited at highest rates in Kankakee in both the fine 4.6 µg/m2-h and coarse 250 µg/m2-h fraction. Finally, estimates of the total amount of trace metals accumulated on paved areas and potentially discharged into the sewer systems by storm water run-off in the urban and rural area are discussed.

Microstructural characterization of laser-melted/roller-quenched dicalcium silicate

1988 ◽  
Vol 46 ◽  
pp. 582-583
Author(s):  
C. J. Chan ◽  
K. R. Venkatachari ◽  
W. M. Kriven ◽  
J. F. Young
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Shape Change ◽  
Microstructural Characterization ◽  
Particle Size Effect ◽  
Dicalcium Silicate ◽  
Laser Melting ◽  
Uniform Size ◽  
Cell Shape Change ◽  
Wide Range

Dicalcium silicate (Ca2SiO4) is a major component of Portland cement. It has also been investigated as a potential transformation toughener alternative to zirconia. It has five polymorphs: α, α'H, α'L, β and γ. Of interest is the β-to-γ transformation on cooling at about 490°C. This transformation, accompanied by a 12% volume increase and a 4.6° unit cell shape change, is analogous to the tetragonal-to-monoclinic transformation in zirconia. Due to the processing methods used, previous studies into the particle size effect were limited by a wide range of particle size distribution. In an attempt to obtain a more uniform size, a fast quench rate involving a laser-melting/roller-quenching technique was investigated.The laser-melting/roller-quenching experiment used precompacted bars of stoichiometric γ-Ca2SiO4 powder, which were synthesized from AR grade CaCO3 and SiO2xH2O. The raw materials were mixed by conventional ceramic processing techniques, and sintered at 1450°C. The dusted γ-Ca2SiO4 powder was uniaxially pressed into 0.4 cm x 0.4 cm x 4 cm bars under 34 MPa and cold isostatically pressed under 172 MPa. The γ-Ca2SiO4 bars were melted by a 10 KW-CO2 laser.

Depletion of coating color components in the blade coating process circulation

TAPPI Journal ◽  
2011 ◽  
Vol 10 (9) ◽  
pp. 17-23 ◽  
Author(s):  
ANNE RUTANEN ◽  
MARTTI TOIVAKKA
Keyword(s):  
Fine Particles ◽  
Particle Density ◽  
Stable Process ◽  
Size Fraction ◽  
Color Stability ◽  
Strong Interactions ◽  
Coating Process ◽  
Size Segregation ◽  
Coating Color ◽  
Average Size

Coating color stability, as defined by changes in its solid particle fraction, is important for runnability, quality, and costs of a paper coating operation. This study sought to determine whether the size or density of particles is important in size segregation in a pigment coating process. We used a laboratory coater to study changes in coating color composition during coating operations. The results suggest that size segregation occurs for high and low density particles. Regardless of the particle density, the fine particle size fraction (<0.2 μm) was the most prone for depletion, causing an increase in the average size of the particles. Strong interactions between the fine particles and other components also were associated with a low depletion tendency of fine particles. A stable process and improved efficiency of fine particles and binders can be achieved by controlling the depletion of fine particles.

The effect of Tin additionon on Structural and magnetic properties of the stannoferrite Li0.5+0.5XFe2.5-1.5XSnXO4

2016 ◽  
Vol 12 (3) ◽  
pp. 4307-4321 ◽  
Author(s):  
Ahmed Hassan Ibrahim ◽  
Yehia Abbas
Keyword(s):  
Particle Size ◽  
Fine Particles ◽  
Magnetic Moments ◽  
Lithium Ferrite ◽  
Tem Analysis ◽  
Weiss Temperature ◽  
X Ray ◽  
Two Phases ◽  
Nanocrystalline Ferrite ◽  
20 Nm

The physical properties of ferrites are verysensitive to microstructure, which in turn critically dependson the manufacturing process.Nanocrystalline Lithium Stannoferrite system Li0.5+0.5XFe2.5-1.5XSnXO4,X= (0, 0.2, 0.4, 0.6, 0.8 and 1.0) fine particles were successfully prepared by double sintering ceramic technique at pre-sintering temperature of 500oC for 3 h andthepre-sintered material was crushed and sintered finally in air at 1000oC.The structural and microstructural evolutions of the nanophase have been studied using X-ray powder diffraction (XRD) and the Rietveld method.The refinement results showed that the nanocrystalline ferrite has a two phases of ordered and disordered phases for polymorphous lithium Stannoferrite.The particle size of as obtained samples were found to be ~20 nm through TEM that increases up to ~ 85 nmand isdependent on the annealing temperature. TEM micrograph reveals that the grains of sample are spherical in shape. (TEM) analysis confirmed the X-ray results.The particle size of stannic substituted lithium ferrite fine particle obtained from the XRD using Scherrer equation.Magneticmeasurements obtained from lake shore’s vibrating sample magnetometer (VSM), saturation magnetization ofordered LiFe5O8 was found to be (57.829 emu/g) which was lower than disordered LiFe5O8(62.848 emu/g).Theinterplay between superexchange interactions of Fe3+ ions at A and B sublattices gives rise to ferrimagnetic ordering of magnetic moments,with a high Curie-Weiss temperature (TCW ~ 900 K).

scholarly journals Contribution of Fine Particles to Air Emission at Different Phases of Biomass Burning

Atmosphere ◽  
2019 ◽  
Vol 10 (5) ◽  
pp. 278 ◽  
Author(s):  
Niloofar Ordou ◽  
Igor E. Agranovski
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Fine Particles ◽  
Combustion Process ◽  
Coarse Particles ◽  
Biomass Smoke ◽  
Smoke Particles ◽  
Air Emission ◽  
Entire Duration ◽  
Diffusion Properties

Particle size distribution in biomass smoke was observed for different burning phases, including flaming and smouldering, during the combustion of nine common Australian vegetation representatives. Smoke particles generated during the smouldering phase of combustions were found to be coarser as compared to flaming aerosols for all hard species. In contrast, for leafy species, this trend was inversed. In addition, the combustion process was investigated over the entire duration of burning by acquiring data with one second time resolution for all nine species. Particles were separately characterised in two categories: fine particles with dominating diffusion properties measurable with diffusion-based instruments (Dp < 200 nm), and coarse particles with dominating inertia (Dp > 200 nm). It was found that fine particles contribute to more than 90 percent of the total fresh smoke particles for all investigated species.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Synthesis and Advanced Characterization of Polymer-Protein Core-Shell Nanoparticles

Catalysts ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 730
Author(s):  
Erik Sarnello ◽  
Tao Li
Keyword(s):  
Particle Size ◽  
Small Angle ◽  
Core Shell ◽  
Assembly Process ◽  
Shell Nanoparticles ◽  
X Ray ◽  
X Ray Scattering ◽  
Wide Range ◽  
Core Shell Nanoparticles ◽  
Ray Scattering

Enzyme immobilization techniques are widely researched due to their wide range of applications. Polymer–protein core–shell nanoparticles (CSNPs) have emerged as a promising technique for enzyme/protein immobilization via a self-assembly process. Based on the desired application, different sizes and distribution of the polymer–protein CSNPs may be required. This work systematically studies the assembly process of poly(4-vinyl pyridine) and bovine serum albumin CSNPs. Average particle size was controlled by varying the concentrations of each reagent. Particle size and size distributions were monitored by dynamic light scattering, ultra-small-angle X-ray scattering, small-angle X-ray scattering and transmission electron microscopy. Results showed a wide range of CSNPs could be assembled ranging from an average radius as small as 52.3 nm, to particles above 1 µm by adjusting reagent concentrations. In situ X-ray scattering techniques monitored particle assembly as a function of time showing the initial particle growth followed by a decrease in particle size as they reach equilibrium. The results outline a general strategy that can be applied to other CSNP systems to better control particle size and distribution for various applications.

scholarly journals CHARACTERISTICS AND ADSORPTION PERFORMANCE OF FORMULATED TRIKOTAC FILTER AIDS

2019 ◽  
Vol 81 (3) ◽  
Author(s):  
N. Masdiana ◽  
M. Rashid ◽  
S. Hajar ◽  
M. R. Ammar
Keyword(s):  
Particle Size ◽  
Activated Carbon ◽  
Particle Density ◽  
Adsorption Properties ◽  
The Other ◽  
Bet Surface Area ◽  
Adsorption Performance ◽  
Filtration System ◽  
Filter Aids ◽  
The Relationship

TrikotAC filter aids is a combination of a pre-coating material PreKot™ with two adsorbents; activated carbon and lime and their characteristics were investigated in this study. TrikotAC was formulated into three different weight ratios of 5:1:94, 10:1:89 and 10:5:85, respectively. The relationship between adsorption properties and characteristics of the formulated materials particle size distribution, particle density, bulk density, and BET surface area were investigated. The results showed that the adsorption capacity for TrikotAC 10:5:85 (11.88 mg/g) was higher than for the other formulated filter aids samples, and the formulated filter aids material TrikotAC showed promising characteristic as a filter aids and adsorbent for organic compound in fabric filtration system.

Effects of Multiple Impacts and Size Distribution of Particles on Erosion Predictions Using CFD

2007 ◽  
Author(s):  
Yongli Zhang ◽  
Brenton S. McLaury ◽  
Siamack A. Shirzai
Keyword(s):  
Experimental Data ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Target Material ◽  
Average Particle ◽  
Multiple Impacts ◽  
Cfd Simulations ◽  
Erosion Damage ◽  
Wide Range

Erosion equations are usually obtained from experiments by impacting solid particles entrained in a gas or liquid on a target material. The erosion equations are utilized in CFD (Computational Fluid Dynamics) models to predict erosion damage caused by solid particle impingements. Many erosion equations are provided in terms of an erosion ratio. By definition, the erosion ratio is the mass loss of target material divided by the mass of impacting particles. The mass of impacting particles is the summation of (particle mass × number of impacts) of each particle. In erosion experiments conducted to determine erosion equations, some particles may impact the target wall many times and some other particles may not impact the target at all. Therefore, the experimental data may not reflect the actual erosion ratio because the mass of the sand that is used to run the experiments is assumed to be the mass of the impacting particles. CFD and particle trajectory simulations are applied in the present work to study effects of multiple impacts on developing erosion ratio equations. The erosion equation as well as the CFD-based erosion modeling procedure is validated against a variety of experimental data. The results show that the effect of multiple impacts is negligible in air cases. In water cases, however, this effect needs to be accounted for especially for small particles. This makes it impractical to develop erosion ratio equations from experimental data obtained for tests with sand in water or dense gases. Many factors affecting erosion damage are accounted for in various erosion equations. In addition to some well-studied parameters such as particle impacting speed and impacting angle, particle size also plays a significant role in the erosion process. An average particle size is usually used in analyzing experimental data or estimating erosion damage cases of practical interest. In petroleum production applications, however, the size of sand particles that are entrained in produced fluids can vary over a fairly broad range. CFD simulations are also performed to study the effect of particle size distribution. In CFD simulations, particle sizes are normally distributed with the mean equaling the average size of interest and the standard deviation varying over a wide range. Based on CFD simulations, an equation is developed and can be applied to account for the effect of the particle size distribution on erosion prediction for gases and liquids.

Sign in / Sign up

Export Citation Format

Share Document