scholarly journals Analysis and Design of Ultra-Wideband 3-Way Bagley Power Divider Using Tapered Lines Transformers

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Khair Al Shamaileh ◽  
Abdullah Qaroot ◽  
Nihad Dib ◽  
Abdelfattah Sheta ◽  
Majeed A. Alkanhal
Keyword(s):  
Design Procedure ◽  
Ultra Wideband ◽  
Power Divider ◽  
Frequency Range ◽  
Analysis And Design ◽  
Wave Simulation ◽  
Full Wave ◽  
Quarter Wave ◽  
Simulation Results

An ultra-wideband (UWB) modified 3-way Bagley polygon power divider (BPD) that operates over a frequency range of 2–16 GHz is presented. To achieve the UWB operation, the conventional quarter-wave transformers in the BPD are substituted by two tapered line transformers. For verification purposes, the proposed divider is simulated, fabricated, and measured. The agreement between the full-wave simulation results and the measurement ones validates the design procedure.

Compact filtering power dividers with wide upper stopband

2019 ◽  
Vol 11 (08) ◽  
pp. 765-773
Author(s):  
Gaoya Dong ◽  
Weimin Wang ◽  
Yuanan Liu
Keyword(s):  
Transmission Lines ◽  
Wave Transmission ◽  
Coupling Matrix ◽  
Power Dividers ◽  
Full Wave ◽  
Half Wave ◽  
Coupled Lines ◽  
Quarter Wave ◽  
Simulation Results ◽  
Good Agreement

AbstractA series of compact filtering power dividers (FPDs) with simple layouts are proposed based on coupling topology. The structure of the presented FPD1 is composed of three resonators and one isolating resistor. These FPDs can be designed based on coupling matrix filter theory. A half-wave transmission line is employed in FPD2 to introduce a transmission zero (TZ) locating at 1.27f0. The FPD3 is designed by replacing quarter-wave transmission lines in FPD2 with quarter-wave coupled lines, which will produce a TZ locating at 1.96 f0 and extend upper stopband bandwidth. For verification, three FPDs centered at 2.45 GHz are fabricated and measured. All measured results are in good agreement with the full-wave simulation results.

Design of multi-layered bandpass filter with independently controllable triple-passband response

2014 ◽  
Vol 6 (6) ◽  
pp. 611-618 ◽  
Author(s):  
Yung-Wei Chen ◽  
Hung-Wei Wu ◽  
Yan-Kuin Su
Keyword(s):  
Frequency Response ◽  
Bandpass Filter ◽  
Bottom Layer ◽  
Wide Frequency Range ◽  
Electromagnetic Simulation ◽  
Frequency Range ◽  
High Isolation ◽  
Full Wave ◽  
Simulation Results ◽  
Good Agreement

In this paper, a new multi-layered triple-passband bandpass filter using embedded and stub-loaded stepped impedance resonators (SIRs) is proposed. The filter is designed to have triple-passband at 1.8, 2.4, and 3.5 GHz. The 1st and 2nd passbands (1.8/2.4 GHz) are simultaneously generated by controlling the impedance and length ratios of the embedded SIRs (on top layer). The 3rd passband (3.5 GHz) is generated by using the stub-loaded SIR (on bottom layer). Using the embedded SIR, the even modes can be tuned within very wide frequency range and without affecting the odd modes. Therefore, the design of multi-band filters with very close passbands can be easily achieved and having a high isolation between the passbands. The filter can provide the multi-path propagation to enhance the frequency response and achieving the compact circuit size. The measured results are in good agreement with the full-wave electromagnetic simulation results.

Design of an Ultra-Wideband Wilkinson Power Divider in Modern Electronic Engineering

2015 ◽  
Vol 713-715 ◽  
pp. 1048-1051
Author(s):  
Xin Cao ◽  
Zong Xi Tang
Keyword(s):  
Communication Systems ◽  
Ultra Wideband ◽  
Power Divider ◽  
Frequency Range ◽  
Resonance Property ◽  
Electronic Engineering ◽  
Quarter Wavelength ◽  
Working Frequency ◽  
Wilkinson Power Divider ◽  
Good Agreement

In this paper, an ultra-wideband Wilkinson power divider based on the quarter wavelength transformation is proposed. The proposed power divider utilizes the resonance property of the four stage quarter wavelength microstrip stubs to increase the isolation between the to output ports. As the measured results show that, the power divider has the insertion loss less than 1.3dB with the minimum isolation 15.4dB in the working frequency range from 1GHz to 5GHz. The simulated results and measured results are in good agreement and the proposed power divider can be applied in the communication systems in modern electronic engineering.

scholarly journals A Miniaturized Transmitting LPDA Design for 2 MHz–30 MHz Uses

Sensors ◽  
2021 ◽  
Vol 21 (18) ◽  
pp. 6034
Author(s):  
Wenjun Zhu ◽  
Lixin Guo
Keyword(s):  
High Frequency ◽  
Optimization Methods ◽  
Directional Pattern ◽  
Electrical Performance ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Wave Simulation ◽  
Full Wave ◽  
Coefficient Optimization ◽  
Simulation Results

A miniaturized horizontal polarized high frequency transmitting LPDA is presented. In use of the dipole transformation and antenna coefficient optimization methods, a 65% reduction in the size was achieved with the electrical performance kept in a competitive level. Full-wave simulation results showed a stable directional pattern and lower VSWR over the impedance bandwidth of 2 to 30 MHz. The gain bandwidth can reach the range of 4–30 MHz, meanwhile, there is only minor degradation on gain in frequencies under 4 MHz.

scholarly journals A Miniaturized Dual-Mode Bandpass Filter Using Slot Spurline Technique

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Haiwen Liu ◽  
Jiuhuai Lei ◽  
Jing Wan ◽  
Yan Wang ◽  
Feng Yang ◽  
...  
Keyword(s):  
Elliptic Function ◽  
Bandpass Filter ◽  
Dual Mode ◽  
Wave Simulation ◽  
Full Wave ◽  
Filter Characteristic ◽  
Simulation Results ◽  
Degenerate Modes ◽  
Good Agreement

A miniaturized dual-mode bandpass filter (BPF) with elliptic function response using slot spurline is designed in this paper. The slot spurline can not only splits the degenerate modes but also determine the type of filter characteristic (Chebyshev or elliptic). To miniaturize the resonator, four sagittate stubs are proposed. For demonstration purpose, a BPF operating at 5.75 GHz for WLAN application was designed, fabricated, and measured. The measured results are in good agreement with the full-wave simulation results.

UWB Bandpass Filter with Ultra-wide Stopband based on Ring Resonator

Frequenz ◽  
2018 ◽  
Vol 72 (5-6) ◽  
pp. 245-252 ◽  
Author(s):  
Maryam Kazemi ◽  
Saeedeh Lotfi ◽  
Hesam Siahkamari ◽  
Mahmood Mohammadpanah
Keyword(s):  
Bandpass Filter ◽  
Ring Resonator ◽  
Ultra Wideband ◽  
Design System ◽  
Filter Performance ◽  
Full Wave ◽  
Measurement Results ◽  
Operational Frequency ◽  
Simulation Results ◽  
Good Agreement

AbstractAn ultra-wideband (UWB) bandpass filter with ultra-wide stopband based on a rectangular ring resonator is presented. The filter is designed for the operational frequency band from 4.10 GHz to 10.80 GHz with an ultra-wide stopband from 11.23 GHz to 40 GHz. The even and odd equivalent circuits are used to achieve a suitable analysis of the proposed filter performance. To verify the design and analysis, the proposed bandpass filter is simulated using full-wave EM simulator Advanced Design System and fabricated on a 20mil thick Rogers_RO4003 substrate with relative permittivity of 3.38 and a loss tangent of 0.0021. The proposed filter behavior is investigated and simulation results are in good agreement with measurement results.

scholarly journals Control of the Radiation Patterns Using Homogeneous and Isotropic Impedance Metasurface

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Fan Yang ◽  
Zhong Lei Mei ◽  
Tie Jun Cui
Keyword(s):  
Point Source ◽  
Surface Impedance ◽  
High Selectivity ◽  
Two Dimensional ◽  
Radiation Patterns ◽  
Wave Simulation ◽  
Full Wave ◽  
Low Profile ◽  
Simulation Results

We propose to control the radiation patterns of a two-dimensional (2D) point source by using impedance metasurfaces. We show that the radiation patterns can be manipulated by altering the surface impedance of the metasurface. Full-wave simulation results are provided to validate the theoretical derivations. The proposed design enjoys novel properties of isotropy, homogeneity, low profile, and high selectivity of frequency, making it potentially applicable in many applications. We also point out that this design can be implemented with active metasurfaces and the surface impedance can be tuned by modulating the value of loaded elements, like resistors, inductors, and capacitors.

Tunable High-Q TSV Inductor Packaging with MEMS

2015 ◽  
Vol 2015 (1) ◽  
pp. 000062-000066 ◽  
Author(s):  
Bruce Kim ◽  
Saikat Mondal ◽  
Sang-Bock Cho
Keyword(s):  
Mechanical Systems ◽  
Micro Electro Mechanical Systems ◽  
Frequency Bands ◽  
High Isolation ◽  
High Q ◽  
Wave Simulation ◽  
Full Wave ◽  
Leakage Resistance ◽  
Simulation Results ◽  
Tunable Inductor

In this paper, we present a Through-Silicon-Via (TSV)-based 3D tunable inductor implementation for RF applications. The proposed inductor structure uses MEMS (Micro Electro-Mechanical Systems) switches to vary inductance by activating and deactivating the switches. MEMS-based switches are used to offer high isolation in the off state. The tunable inductor is tested within an LNA circuit for variation in off-state leakage resistance. Detailed 3D full wave simulation results are presented for different cellular frequency bands.

Sign in / Sign up

Export Citation Format

Share Document