scholarly journals A Miniaturized Dual-Mode Bandpass Filter Using Slot Spurline Technique

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Haiwen Liu ◽  
Jiuhuai Lei ◽  
Jing Wan ◽  
Yan Wang ◽  
Feng Yang ◽  
...  
Keyword(s):  
Elliptic Function ◽  
Bandpass Filter ◽  
Dual Mode ◽  
Wave Simulation ◽  
Full Wave ◽  
Filter Characteristic ◽  
Simulation Results ◽  
Degenerate Modes ◽  
Good Agreement

A miniaturized dual-mode bandpass filter (BPF) with elliptic function response using slot spurline is designed in this paper. The slot spurline can not only splits the degenerate modes but also determine the type of filter characteristic (Chebyshev or elliptic). To miniaturize the resonator, four sagittate stubs are proposed. For demonstration purpose, a BPF operating at 5.75 GHz for WLAN application was designed, fabricated, and measured. The measured results are in good agreement with the full-wave simulation results.

Design of multi-layered bandpass filter with independently controllable triple-passband response

2014 ◽  
Vol 6 (6) ◽  
pp. 611-618 ◽  
Author(s):  
Yung-Wei Chen ◽  
Hung-Wei Wu ◽  
Yan-Kuin Su
Keyword(s):  
Frequency Response ◽  
Bandpass Filter ◽  
Bottom Layer ◽  
Wide Frequency Range ◽  
Electromagnetic Simulation ◽  
Frequency Range ◽  
High Isolation ◽  
Full Wave ◽  
Simulation Results ◽  
Good Agreement

In this paper, a new multi-layered triple-passband bandpass filter using embedded and stub-loaded stepped impedance resonators (SIRs) is proposed. The filter is designed to have triple-passband at 1.8, 2.4, and 3.5 GHz. The 1st and 2nd passbands (1.8/2.4 GHz) are simultaneously generated by controlling the impedance and length ratios of the embedded SIRs (on top layer). The 3rd passband (3.5 GHz) is generated by using the stub-loaded SIR (on bottom layer). Using the embedded SIR, the even modes can be tuned within very wide frequency range and without affecting the odd modes. Therefore, the design of multi-band filters with very close passbands can be easily achieved and having a high isolation between the passbands. The filter can provide the multi-path propagation to enhance the frequency response and achieving the compact circuit size. The measured results are in good agreement with the full-wave electromagnetic simulation results.

UWB Bandpass Filter with Ultra-wide Stopband based on Ring Resonator

Frequenz ◽  
2018 ◽  
Vol 72 (5-6) ◽  
pp. 245-252 ◽  
Author(s):  
Maryam Kazemi ◽  
Saeedeh Lotfi ◽  
Hesam Siahkamari ◽  
Mahmood Mohammadpanah
Keyword(s):  
Bandpass Filter ◽  
Ring Resonator ◽  
Ultra Wideband ◽  
Design System ◽  
Filter Performance ◽  
Full Wave ◽  
Measurement Results ◽  
Operational Frequency ◽  
Simulation Results ◽  
Good Agreement

AbstractAn ultra-wideband (UWB) bandpass filter with ultra-wide stopband based on a rectangular ring resonator is presented. The filter is designed for the operational frequency band from 4.10 GHz to 10.80 GHz with an ultra-wide stopband from 11.23 GHz to 40 GHz. The even and odd equivalent circuits are used to achieve a suitable analysis of the proposed filter performance. To verify the design and analysis, the proposed bandpass filter is simulated using full-wave EM simulator Advanced Design System and fabricated on a 20mil thick Rogers_RO4003 substrate with relative permittivity of 3.38 and a loss tangent of 0.0021. The proposed filter behavior is investigated and simulation results are in good agreement with measurement results.

Compact dual-band bandpass filter using open stub-loaded stepped impedance resonator with cross-slots

2016 ◽  
Vol 9 (2) ◽  
pp. 269-274 ◽  
Author(s):  
Bukuru Denis ◽  
Kaijun Song ◽  
Fan Zhang
Keyword(s):  
Bandpass Filter ◽  
Design Concept ◽  
Dual Band ◽  
High Isolation ◽  
Transmission Zeros ◽  
Full Wave ◽  
Measurement Results ◽  
Stepped Impedance Resonator ◽  
Simulation Results ◽  
Good Agreement

A compact dual-band bandpass filter using stub-loaded stepped impedance resonator (SLSIR) with cross-slots is presented. The symmetric SLSIR is analyzed using even- and odd-mode techniques. Design equations are derived and they are used to guide the design of the circuits. Two passbands can be easily tuned by cross-slots and open stubs. Transmission zeros among each passbands are created, resulting in high isolation and frequency selectivity. An experimental circuit is fabricated and evaluated to validate the design concept. The fabricated filter is compact with 19.76 × 12.7 mm2. The measurement results are in good agreement with the full-wave simulation results.

Compact dual-mode microstrip bandpass filter based on slotted square patch resonator

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Karthie S. ◽  
Zuvairiya Parveen J. ◽  
Yogeshwari D. ◽  
Venkadeshwari E.
Keyword(s):  
Bandpass Filter ◽  
Filter Design ◽  
Center Frequency ◽  
Dual Mode ◽  
Content Type ◽  
Transmission Zeros ◽  
Compact Size ◽  
Mode Response ◽  
Better Than ◽  
Good Agreement

Purpose The purpose of this paper is to present the design of a compact microstrip bandpass filter (BPF) in dual-mode configuration loaded with cross-loop and square ring slots on a square patch resonator for C-band applications. Design/methodology/approach In the proposed design, the dual-mode response for the filter is realized with two transmission zeros (TZs) by the insertion of a perturbation element at the diagonal corner of the square patch resonator with orthogonal feed lines. Such TZs at the edges of the passband result in better selectivity for the proposed BPF. Moreover, the cross-loop and square ring slots are etched on a square patch resonator to obtain a miniaturized BPF. Findings The proposed dual-mode microstrip filter fabricated in RT/duroid 6010 substrate using PCB technology has a measured minimum insertion loss of 1.8 dB and return loss better than 24.5 dB with a fractional bandwidth (FBW) of 6.9%. A compact size of 7.35 × 7.35 mm2 is achieved for the slotted patch resonator-based dual-mode BPF at the center frequency of 4.76 GHz. As compared with the conventional square patch resonator, a size reduction of 61% is achieved with the proposed slotted design. The feasibility of the filter design is confirmed by the good agreement between the measured and simulated responses. The performance of the proposed filter structure is compared with other dual-mode filter works. Originality/value In the proposed work, a compact dual-mode BPF is reported with slotted structures. The conventional square patch resonator is deployed with cross-loop and square ring slots to design a dual-mode filter with a square perturbation element at its diagonal corner. The proposed filter exhibits compact size and favorable performance compared to other dual-mode filter works reported in literature. The aforementioned design of the dual-mode BPF at 4.76 GHz is suitable for applications in the lower part of the C-band.

scholarly journals A New Ultracompact Narrow Bandpass Microstrip Filter Using Double-Negative Quasiplanar Cells

2020 ◽  
Vol 2020 ◽  
pp. 1-6
Author(s):  
Mohammad Reza Khawary ◽  
Vahid Nayyeri ◽  
Seyed Mohammad Hashemi ◽  
Mohammad Soleimani
Keyword(s):  
Printed Circuit Board ◽  
High Selectivity ◽  
Bandpass Filter ◽  
Circuit Board ◽  
Center Frequency ◽  
Double Negative ◽  
Fractional Bandwidth ◽  
Printed Circuit ◽  
Full Wave ◽  
Good Agreement

This paper presents a novel ultracompact narrow bandpass filter with high selectivity. The proposed filter is composed of cascading two basic cells. Each cell is basically a microstrip line loaded with a quasiplanar resonator and series gaps which can be fabricated using a standard multilayer printed circuit board technology. The structure is analyzed through an equivalent circuit and full-wave simulations. The simulation results are compared with experimental measurements demonstrating a good agreement between them. The measurement indicates that the realized bandpass filter at the center frequency of 1 GHz has a fractional bandwidth of 2.2%. Most importantly, in comparison with other similar recent works, it is shown that the proposed filter has the smallest size.

Compact filtering power dividers with wide upper stopband

2019 ◽  
Vol 11 (08) ◽  
pp. 765-773
Author(s):  
Gaoya Dong ◽  
Weimin Wang ◽  
Yuanan Liu
Keyword(s):  
Transmission Lines ◽  
Wave Transmission ◽  
Coupling Matrix ◽  
Power Dividers ◽  
Full Wave ◽  
Half Wave ◽  
Coupled Lines ◽  
Quarter Wave ◽  
Simulation Results ◽  
Good Agreement

AbstractA series of compact filtering power dividers (FPDs) with simple layouts are proposed based on coupling topology. The structure of the presented FPD1 is composed of three resonators and one isolating resistor. These FPDs can be designed based on coupling matrix filter theory. A half-wave transmission line is employed in FPD2 to introduce a transmission zero (TZ) locating at 1.27f0. The FPD3 is designed by replacing quarter-wave transmission lines in FPD2 with quarter-wave coupled lines, which will produce a TZ locating at 1.96 f0 and extend upper stopband bandwidth. For verification, three FPDs centered at 2.45 GHz are fabricated and measured. All measured results are in good agreement with the full-wave simulation results.

Multilayer SIW Dual-Band Filters with Independent Band Characteristics and High Selectivity

Frequenz ◽  
2019 ◽  
Vol 73 (9-10) ◽  
pp. 293-300
Author(s):  
Dinghong Jia ◽  
Jianqin Deng ◽  
Yangping Zhao ◽  
Ke Wu
Keyword(s):  
High Selectivity ◽  
Bandpass Filter ◽  
Large Range ◽  
Metal Layer ◽  
Dual Band ◽  
Effective Dimension ◽  
Dual Mode ◽  
Transmission Zeros ◽  
Design Freedom ◽  
Good Agreement

Abstract This work presents an approach to developing dual-mode dual-band substrate integrated waveguide (SIW) bandpass filter based on multilayer process. TE102/TE201 and TE101/TE102 modes are used to feature the two passbands, respectively. To begin with, large range of band location ratios are decided by the effective dimension of the SIW resonator. With reference to the field distribution, independent coupling schemes of the dual-modes are then realized by slots or circular apertures etched on the middle metal layer. It allows to not only introduce a large design freedom of bandwidth but also keep compactness. Finally, source-load and mixed couplings are deployed to produce transmission zeros around the passband in providing a sharp selectivity in the two filters, respectively. The details to independently control the center frequencies and bandwidth of two passbands are also presented. A two-order double-layered and a triple-layered SIW dual-band bandpass filter are prototyped to evaluate the proposed design approach, respectively. Results show a good agreement between simulations and measurements. The proposed filter exhibits flexible design freedom, high selectivity as well as good out-of-band rejection.

scholarly journals A Miniaturized Transmitting LPDA Design for 2 MHz–30 MHz Uses

Sensors ◽  
2021 ◽  
Vol 21 (18) ◽  
pp. 6034
Author(s):  
Wenjun Zhu ◽  
Lixin Guo
Keyword(s):  
High Frequency ◽  
Optimization Methods ◽  
Directional Pattern ◽  
Electrical Performance ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Wave Simulation ◽  
Full Wave ◽  
Coefficient Optimization ◽  
Simulation Results

A miniaturized horizontal polarized high frequency transmitting LPDA is presented. In use of the dipole transformation and antenna coefficient optimization methods, a 65% reduction in the size was achieved with the electrical performance kept in a competitive level. Full-wave simulation results showed a stable directional pattern and lower VSWR over the impedance bandwidth of 2 to 30 MHz. The gain bandwidth can reach the range of 4–30 MHz, meanwhile, there is only minor degradation on gain in frequencies under 4 MHz.

scholarly journals Substrate integrated waveguide bandpass filter for short range device application using rectangular open loop resonator

2021 ◽  
Vol 11 (5) ◽  
pp. 3747
Author(s):  
Dian Widi Astuti ◽  
Rizki Ramadhan Putra ◽  
Muslim Muslim ◽  
Mudrik Alaydrus
Keyword(s):  
Short Range ◽  
Return Loss ◽  
Bandpass Filter ◽  
Open Loop ◽  
Frequency Region ◽  
Substrate Integrated Waveguide ◽  
Network Analyzer ◽  
Measurement Results ◽  
Simulation Results ◽  
Good Agreement

The substrate integrated waveguide (SIW) structure is the candidate for many application in microwave, terahertz and millimeter wave application. It because of SIW structure can integrate with any component in one substrate than others structure. A kind components using SIW structure is a filter component, especialy bandpass filter. This research recommended SIW bandpass filter using rectangular open loop resonator for giving more selectivity of filter. It can be implemented for short range device (SRD) application in frequency region 2.4 - 2.483 GHz. Two types of SIW bandpass filter are proposed. First, SIW bandpass filter is proposed using six rectangular open loop resonators while the second SIW bandpass filter used eight rectangular open loop resonators. The simulation results for two kinds of the recommended rectangular open loop resonators have insertion loss (S<sub>21</sub> parameter) below 2 dB and return loss (S<sub>11</sub> parameter) more than 10 dB. Fabrication of the recommended two kind filters was validated by Vector Network Analyzer. The measurement results for six rectangular open loop resonators have 1.32 dB for S<sub>21</sub> parameter at 2.29 GHz while the S<sub>11</sub> parameter more than 18 dB at 2.26 GHz – 2.32 GHz. While the measurement results has good agreement for eight rectangular open loop resonators. Its have S<sub>21</sub> below 2.2 dB at 2.41 – 2.47 GHz and S<sub>11</sub> 16.27 dB at 2.38 GHz and 11.5 dB at 2.47 GHz.

Sign in / Sign up

Export Citation Format

Share Document