scholarly journals The Effect of Deposition Rate on Electrical, Optical and Structural Properties of ITO Thin Films

2005 ◽  
Vol 2 (3) ◽  
pp. 171-177 ◽  
Author(s):  
P. S. Raghupathi ◽  
Joseph George ◽  
C. S. Menon
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Deposition Rate ◽  
Indium Tin Oxide ◽  
Visible Region ◽  
Band Gap Energy ◽  
Electrical And Optical Properties ◽  
Glass Substrates ◽  
Ito Thin Films ◽  
Evaporation Technique

Indium tin oxide (ITO) thin films have been prepared using the reactive evaporation technique on glass substrates in an oxygen atmosphere. It is found that the deposition rate plays prominent role in controlling the electrical and optical properties of the ITO thin films. Resistivity, electrical conductivity, activation energy, optical transmission and band gap energy were investigated. A transmittance value of more than 90% in the visible region of the spectrum and an electrical conductivity of 3x10–6Ωm has been obtained with a deposition rate of 2 nm/min. XRD studies showed that the films are polycrystalline.

Synthesis and Characterization of Deposited NiO Thin Films by Spray Pyrolysis Technique

2019 ◽  
Vol 17 (17) ◽  
pp. 27-32
Author(s):  
Chouaieb Zaouche ◽  
Yacine Aoun ◽  
Said Benramache ◽  
Abdelouahab Gahtar
Keyword(s):  
Thin Films ◽  
Spray Pyrolysis ◽  
Deposition Rate ◽  
Spray Pyrolysis Technique ◽  
Visible Region ◽  
Band Gap Energy ◽  
Electrical And Optical Properties ◽  
Minimum Value ◽  
Average Transmittance

AbstractIn this work, nickel oxide was fabricated on glass substrate at 450 °C by spray pyrolysis technique. The NiO layers were obtained with 0.05M molarity, which were deposited by various deposition rates 20, 40, 60 and 80 ml. The effects of deposition rate on the structural, electrical and optical properties were examined. All fabricated NiO thin films were observed a nanocrystalline a cubic structure with a strong (111) preferred orientation, it is only phase was observed in all deposited NiO. The film elaborated with 60 ml have a minimum value of crystallite size was 15.8 nm. All NiO thin films have an average transmittance is about 70 % in the visible region. The NiO thin films have a verity in the band gap energy from 3.34 to 3.51 eV because the effect of deposition, the minimum value was found at 80 ml, this condition have a lowest Urbach energy. The NiO thin films have an electrical resistivity was decreased from 0.625 to 0.152 (Ω.cm) with increasing the deposition rate from 20 to 80ml. The best results of NiO thin films are obtained in the deposition NiO films by 40 and 80 ml.

scholarly journals Studies on the Electrical and Optical Properties of Magnesium Phthalocyanine Thin Films

2004 ◽  
Vol 1 (5) ◽  
pp. 231-236
Author(s):  
T. G. Gopinathan ◽  
C. S. Menon
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Visible Region ◽  
Absolute Temperature ◽  
Post Deposition Annealing ◽  
Glass Substrates ◽  
Absorption Studies ◽  
Evaporation Technique ◽  
Uv Visible ◽  
Post Deposition

Thin films of Magnesium Phthalocyanine (MgPc) are prepared by thermal evaporation technique at a base pressure of 10-5m.bar on thoroughly cleaned glass substrates kept at different constant temperatures. Films of thickness 2400 A.U. coated at room temperature are subjected to post deposition annealing in air by keeping them in a furnace at different constant temperatures, for one hour. The electrical conductivity studies are conducted in the temperature range 300 K to 525 K. The electrical conductivity is plotted as a function of absolute temperature. The conduction mechanism is observed to be hopping. The thermal activation energy is calculated in different cases and is observed to vary with substrate temperature and annealing temperature. A phase change is observed due to post-deposition annealing at around 523 K. The optical absorption studies are done in the UV-Visible region. The optical band gap energies of the samples are calculated.

scholarly journals The Effect of Deposition Rate on the Electrical Properties of Indium Tin Oxide (ITO) Thin Films

2015 ◽  
Vol 16 (2) ◽  
pp. 286
Author(s):  
Hadaate Ullah ◽  
Shahin Mahmud ◽  
Fahmida Sharmin Jui
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Deposition Rate ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Vital Role ◽  
Light Emitting ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Ito Thin Films

<p>Indium-tin oxide (ITO) which is optically transparent is referred as a “universal” electrode for various optoelectronic devices such as organic light emitting diodes (OLEDs). It is scientifically proved that the performance of OLEDs raises up significantly by exposing the ITO surface to oxygen plasma. This study employs conducting atomic force microscopy (C-AFM) for unique nanometer-scale mapping of the local current density of a vapor-deposited ITO film. Indium Tin Oxide (ITO) thin films have been prepared by using the reactive evaporation method on glass substrates in an oxygen atmosphere. It is found that the deposition rate plays a vital role in controlling the electrical properties of the ITO thin films. The resistivity and the electrical conductivity were also investigated. The electrical resistivity of 3.10 x10 <sup>–6</sup> Ωm has been obtained with a deposition rate of 2 nm/min.</p>

scholarly journals Improving Performance of CIGS Solar Cells by Annealing ITO Thin Films Electrodes

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Chuan Lung Chuang ◽  
Ming Wei Chang ◽  
Nien Po Chen ◽  
Chung Chiang Pan ◽  
Chung Ping Liu
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Solar Cells ◽  
Indium Tin Oxide ◽  
Copper Indium Gallium Diselenide ◽  
Glass Substrates ◽  
Ito Film ◽  
Ito Thin Films ◽  
Cigs Solar Cells ◽  
Ito Films

Indium tin oxide (ITO) thin films were grown on glass substrates by direct current (DC) reactive magnetron sputtering at room temperature. Annealing at the optimal temperature can considerably improve the composition, structure, optical properties, and electrical properties of the ITO film. An ITO sample with a favorable crystalline structure was obtained by annealing in fixed oxygen/argon ratio of 0.03 at 400°C for 30 min. The carrier concentration, mobility, resistivity, band gap, transmission in the visible-light region, and transmission in the near-IR regions of the ITO sample were-1.6E+20 cm−3,2.7E+01 cm2/Vs,1.4E-03 Ohm-cm, 3.2 eV, 89.1%, and 94.7%, respectively. Thus, annealing improved the average transmissions (400–1200 nm) of the ITO film by 16.36%. Moreover, annealing a copper-indium-gallium-diselenide (CIGS) solar cell at 400°C for 30 min in air improved its efficiency by 18.75%. The characteristics of annealing ITO films importantly affect the structural, morphological, electrical, and optical properties of ITO films that are used in solar cells.

Structural and Optical Properties of InSnO3 Sol-Gel Coatings to Use in Windows Glass Buildings

2010 ◽  
Vol 168-170 ◽  
pp. 2348-2351
Author(s):  
Lazaro De Jesus Dominguez Gallegos ◽  
Angélica Silvestre López Rodríguez ◽  
Pio Sifuentes Gallardo ◽  
Miguel Angel Hernández Rivera ◽  
María Guadalupe Garnica Romo ◽  
...  
Keyword(s):  
Optical Properties ◽  
Indium Tin Oxide ◽  
Sol Gel ◽  
Visible Region ◽  
Optical Transmittance ◽  
Indium Chloride ◽  
Glass Substrates ◽  
Tin Chloride ◽  
Ito Thin Films ◽  
Ito Films

Indium stannate (InSnO3) films doping with small amounts of copper are made highly useful as architectural window coatings. Indium-tin-oxide (ITO) has attracted intense interest due to some of its unique characteristics; it has high optical transmittance in the visible region, low electric resistivity, and chemical stability. Therefore, ITO thin films have been found to play an important role in opto-electronic applications. In this work, uniform and transparent ITO films were deposited onto glass substrates using a sol-gel process. The initial sols were prepared by mixing solutions of indium chloride prepared in anhydrous ethanol with tin chloride and mechanically stirring and refluxed 2 hours and aged 2 week, the resultant mixture until a clear and sticky coating sol was obtained. The glass substrates were spin-coated and annealed at 500 °C. Because annealing conditions affect the microstructures, the properties of the resultant ITO films can be controlled. The optical transmittance of 200 nm thick ITO film was more than 80% in the visible region. The surface morphology examined by SEM appears to be uniform over large surface areas. The structural, microstructural and optical properties of the coatings and powders made from the sols were extensively characterized by using XRD, AFM and spectrophotometer techniques

INFLUENCE OF SUBSTRATE TEMPERATURE ON STRUCTURAL, ELECTRICAL AND OPTICAL PROPERTIES OF ITO THIN FILMS PREPARED BY RF MAGNETRON SPUTTERING

2013 ◽  
Vol 20 (05) ◽  
pp. 1350045 ◽  
Author(s):  
BO HE ◽  
LEI ZHAO ◽  
JING XU ◽  
HUAIZHONG XING ◽  
SHAOLIN XUE ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Visible Region ◽  
Rf Magnetron Sputtering ◽  
Electrical And Optical Properties ◽  
High Quantum Efficiency ◽  
Ito Thin Films ◽  
Ito Films

In this paper, we investigated indium-tin-oxide (ITO) thin films on glass substrates deposited by RF magnetron sputtering using ceramic target to find the optimal condition for fabricating optoelectronic devices. The structural, electrical and optical properties of the ITO films prepared at various substrate temperatures were investigated. The results indicate the grain size increases with substrate temperature increases. As the substrate temperature grew up, the resistivity of ITO films greatly decreased. The ITO film possesses high quality in terms of electrode functions, when substrate temperature is 480°C. The resistivity is as low as 9.42 × 10-5 Ω• cm , while the carrier concentration and mobility are as high as 3.461 × 1021 atom∕cm3 and 19.1 cm2∕V⋅s, respectively. The average transmittance of the film is about 95% in the visible region. The novel ITO/np-Silicon frame, which prepared by RF magnetron sputtering at 480°C substrate temperature, can be used not only for low-cost solar cell, but also for high quantum efficiency of UV and visible lights enhanced photodetector for various applications.

scholarly journals Effect of Oxygen Flow Rate on Properties of Aluminum-Doped Indium-Saving Indium Tin Oxide (ITO) Thin Films Sputtered on Preheated Glass Substrates

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1604
Author(s):  
Svitlana Petrovska ◽  
Ruslan Sergiienko ◽  
Bogdan Ilkiv ◽  
Takashi Nakamura ◽  
Makoto Ohtsuka
Keyword(s):  
Thin Films ◽  
Flow Rate ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Oxygen Flow Rate ◽  
Oxygen Flow ◽  
Visible Range ◽  
Oxide Content ◽  
Glass Substrates ◽  
Ito Thin Films

Amorphous aluminum-doped indium tin oxide (ITO) thin films with a reduced indium oxide content of 50 mass% were manufactured by co-sputtering of ITO and Al2O3 targets in a mixed argon–oxygen atmosphere onto glass substrates preheated at 523 K. The oxygen gas flow rate and heat treatment temperature effects on the electrical, optical and structural properties of the films were studied. Thin films were characterized by means of a four-point probe, ultraviolet–visible-infrared (UV–Vis-IR) spectroscopy and X-ray diffraction. Transmittance of films and crystallization temperature increased as a result of doping of the ITO thin films by aluminum. The increase in oxygen flow rate led to an increase in transmittance and hindering of the crystallization of the aluminum-doped indium saving ITO thin films. It has been found that the film sputtered under optimal conditions showed a volume resistivity of 713 µΩcm, mobility of 30.8 cm2/V·s, carrier concentration of 2.9 × 1020 cm−3 and transmittance of over 90% in the visible range.

scholarly journals Nanostructural Characterisation and Optical Properties of Sputter-Deposited Thick Indium Tin Oxide (ITO) Coatings

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1127
Author(s):  
Andrius Subacius ◽  
Bill Baloukas ◽  
Etienne Bousser ◽  
Steve J. Hinder ◽  
Mark A. Baker ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Nanocrystalline Structure ◽  
Optical Transmittance ◽  
Glass Substrates ◽  
Ito Thin Films ◽  
Sputter Deposited ◽  
Thick Coatings

Indium tin oxide (ITO) thin films, used in many optoelectronic applications, are typically grown to a thickness of a maximum of a few hundred nanometres. In this work, the composition, microstructure and optical/electrical properties of thick ITO coatings deposited by radio frequency magnetron sputtering from a ceramic ITO target in an Ar/O2 gas mixture (total O2 flow of 1%) on unheated glass substrates are reported for the first time. In contrast to the commonly observed (200) or (400) preferential orientations in ITO thin films, the approximately 3.3 μm thick coatings display a (622) preferential orientation. The ITO coatings exhibit a purely nanocrystalline structure and show good electrical and optical properties, such as an electrical resistivity of 1.3 × 10−1 Ω·cm, optical transmittance at 550 nm of ~60% and optical band gap of 2.9 eV. The initial results presented here are expected to provide useful information for future studies on the synthesis of high-quality thick ITO coatings.

EFFECT OF THICKNESS ON THE PROPERTIES OF In-DOPED ZnO THIN FILMS PREPARED BY RF MAGNETRON SPUTTERING

2011 ◽  
Vol 25 (07) ◽  
pp. 995-1003 ◽  
Author(s):  
L. P. PENG ◽  
L. FANG ◽  
X. F. YANG ◽  
Q. L. HUANG ◽  
F. WU ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Film Thickness ◽  
Visible Region ◽  
Hexagonal Wurtzite Structure ◽  
Rf Magnetron Sputtering ◽  
Transparent Electrode ◽  
Visible Range ◽  
Electrical And Optical Properties ◽  
Glass Substrates

In-doped zinc oxide ( ZnO:In ) thin films with thickness from 157 nm to 592 nm have been deposited on glass substrates by radio frequency (RF) magnetron sputtering. The effect of the film thickness on the structural, electrical and optical properties of ZnO:In thin films has been investigated. It is found that the films are hexagonal wurtzite structure with c-axis perpendicular to the substrate, and with increasing thickness, the crystallinity, the grains size and the conductivity of the films increases, but the strains along c-axis and the transmittance decrease. The decrease of the resistivity in a thicker film is attributed to the slight increase of the carrier concentration and the significant increase of Hall mobility. The transmittance of all the films is over 80% in the visible region (400–800 nm) and the band gap decrease with the increase of film thickness. The film with the thickness of around 303 nm has the resistivity of 6.07 × 10-3 Ω⋅ cm and the transmittance of 90% in the visible range. Based on the good conductivity and high transmittance, the ZnO:In films prepared by magnetron sputtering can be regarded as a potential transparent electrode.

Sign in / Sign up

Export Citation Format

Share Document