Determination of the Surface Roughness of Passive Film by Gas Adsorption Techniques

1979 ◽  
Vol 126 (10) ◽  
pp. 1720-1722 ◽  
Author(s):  
T. Takaishi ◽  
A. Yusa ◽  
T. Ohgushi
Keyword(s):  
Surface Roughness ◽  
Passive Film ◽  
Gas Adsorption

Optimal Density Determination of Bouguer Anomaly Using Fractal Analysis (Case of study: Charak area,IRAN)

2005 ◽  
Vol 1 (1) ◽  
pp. 21-24
Author(s):  
Hamid Reza Samadi
Keyword(s):  
Surface Roughness ◽  
Fractal Dimension ◽  
Fractal Analysis ◽  
Fractal Geometry ◽  
Host Rock ◽  
Bouguer Anomaly ◽  
Research Area ◽  
Density Difference ◽  
Optimal Density

In exploration geophysics the main and initial aim is to determine density of under-research goals which have certain density difference with the host rock. Therefore, we state a method in this paper to determine the density of bouguer plate, the so-called variogram method based on fractal geometry. This method is based on minimizing surface roughness of bouguer anomaly. The fractal dimension of surface has been used as surface roughness of bouguer anomaly. Using this method, the optimal density of Charak area insouth of Hormozgan province can be determined which is 2/7 g/cfor the under-research area. This determined density has been used to correct and investigate its results about the isostasy of the studied area and results well-coincided with the geology of the area and dug exploratory holes in the text area

Determination of Hurst exponent by optical signal processing applied on surface roughness measurements

2009 ◽  
Author(s):  
José Antonio Marbán Salgado ◽  
Oscar Sarmiento Martínez ◽  
Darwin Mayorga Cruz ◽  
Jorge Uruchurtu Chavarín
Keyword(s):  
Surface Roughness ◽  
Signal Processing ◽  
Hurst Exponent ◽  
Optical Signal Processing ◽  
Optical Signal ◽  
Roughness Measurements

Experimental Determination of Optimal Speeds for Alloy Steels in Plane Turning

2008 ◽  
Author(s):  
T. Srikanth ◽  
V. Kamala
Keyword(s):  
Surface Roughness ◽  
Force Measurement ◽  
Cutting Speed ◽  
Vital Role ◽  
The Other ◽  
Depth Of Cut ◽  
Work Piece ◽  
Material Interface ◽  
Alloy Steels

In machining, speeds play vital role. The operator should know exactly the speed at which machining should be performed to get the required surface finish. In this paper, an attempt is made to determine the optimal cutting speed for machining of alloy steels. Three work piece materials having different hardness are taken and machined using a round nose tool with a coated tip. The tool dynamometer is attached to the tool post for force measurement. Turning operation on the work piece is performed on lathe at four different speeds, keeping the feed and depth of cut constant. Cutting forces acting on the tool, temperature at the tool and material interface are recorded. Power consumed being determined by a wattmeter and surface roughness values are measured. The same procedure is repeated for the other two work-pieces materials and optimal speeds for machining are determined for the three specimens. The results obtained are compared with the theoretical values and found to be very close.

Determination of Spread Activation Energy and Assessment of Wetting Behavior of Solders on Metallic Substrates

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
K. N. Prabhu ◽  
G. Kumar
Keyword(s):  
Surface Roughness ◽  
Operating Temperature ◽  
Substrate Surface ◽  
Substrate Material ◽  
Metallic Substrates ◽  
Wetting Behavior ◽  
Substrate Surface Roughness ◽  
Exponential Power ◽  
Kinetics Of

The effects of substrate material, substrate surface roughness, and operating temperature on the wetting behavior of Sn–37Pb, Sn–3.5Ag, and Sn–9Zn eutectic solders on metallic substrates were investigated. Solder spreading kinetics was successfully represented by the exponential power law (EPL): ϕ=exp(−Kτn). The EPL parameter K has the significance of accelerating the kinetics of relaxation while the parameter n represents the resistance to spreading process (spread resistance parameter). EPL parameters exhibited a decreasing trend with an increase in surface roughness. Estimated activation energies for solder spreading were found to be in between those reported for inert and highly reactive spreading systems.

scholarly journals Determination of Emissivity of Brass Alloy using Infrared Thermographic Technique

2018 ◽  
Vol 65 (3) ◽  
pp. 115-121
Author(s):  
Zorana Lanc ◽  
Milan Zeljković ◽  
Aleksandar Živković ◽  
Branko Štrbac ◽  
Miodrag Hadžistević
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Multiple Regression ◽  
Strong Correlation ◽  
Three Dimensional ◽  
Multiple Regression Model ◽  
Infrared Images ◽  
Cooling Process ◽  
Brass Alloy

Abstract This paper presents the experimental determination of the dependence of emissivity of brass on surface roughness and temperature. The investigation was conducted using the infrared thermographic technique on brass alloy C27200 workpieces with different degrees of surface roughness, during the continuous cooling process. The results obtained showed that the emissivity of the chosen brass alloy increases with greater surface roughness and decreases during the cooling process, its value ranging from 0.07 to 0.19. It was concluded that surface roughness has a greater influence on the increase of the emissivity at higher temperatures, which can be seen in the three-dimensional infrared images. Multiple regression analysis confirmed a strong correlation between the examined parameters and the emissivity, and an original multiple regression model was determined.

Sign in / Sign up

Export Citation Format

Share Document