A Study of Contact Angle of Hydrogen Bubbles Formed by Formaldehyde Oxidation on Copper Electrode

1989 ◽  
Vol 136 (8) ◽  
pp. 2218-2223 ◽  
Author(s):  
H. H. Trieu ◽  
R. R. Chandran ◽  
R. F. Savinell
Keyword(s):  
Contact Angle ◽  
Copper Electrode ◽  
Hydrogen Bubbles ◽  
Formaldehyde Oxidation

Investigation of behavior of the dynamic contact angle in a problem of convective flows

2017 ◽  
Vol 5 (4) ◽  
pp. 27-42
Author(s):  
O.N Goncharova ◽  
◽  
I.V. Marchuk ◽  
A.V. Zakurdaeva ◽  
◽  
...  
Keyword(s):  
Contact Angle ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Convective Flows

Controlling porosity and density of nanocellulose aerogels for superhydrophobic light materials

TAPPI Journal ◽  
2018 ◽  
Vol 17 (03) ◽  
pp. 145-153 ◽  
Author(s):  
Chengua Yu ◽  
Feng Wang ◽  
Shiyu Fu ◽  
Lucian Lucia
Keyword(s):  
Contact Angle ◽  
Freeze Drying ◽  
Engine Oil ◽  
High Porosity ◽  
Water Mixture ◽  
Waste Engine Oil ◽  
Hydrophobically Modified ◽  
Static Contact ◽  
Oil Water ◽  
Hydrophobic Material

A very low-density oil-absorbing hydrophobic material was fabricated from cellulose nanofiber aerogels–coated silane substances. Nanocellulose aerogels (NCA) superabsorbents were prepared by freeze drying cellulose nanofibril dispersions at 0.2%, 0.5%, 0.8%, 1.0%, and 1.5% w/w. The NCA were hydrophobically modified with methyltrimethoxysilane. The surface morphology and wettability were characterized by scanning electron microscopy and static contact angle. The aerogels displayed an ultralow density (2.0–16.7 mg·cm-3), high porosity (99.9%–98.9%), and superhydrophobicity as evidenced by the contact angle of ~150° that enabled the aerogels to effectively absorb oil from an oil/water mixture. The absorption capacities of hydrophobic nanocellulose aerogels for waste engine oil and olive oil could be up to 140 g·g-1 and 179.1 g·g-1, respectively.

High Resolution Displacement of Functional Groups onto Fluorocarbon Resin Surface by Using ArF Excimer Laser

1996 ◽  
Vol 451 ◽  
Author(s):  
T. Shimizu ◽  
M. Murahara
Keyword(s):  
Contact Angle ◽  
High Resolution ◽  
Laser Beam ◽  
Thin Layer ◽  
Functional Groups ◽  
Excimer Laser ◽  
Laser Fluence ◽  
Large Area ◽  
Three Solutions ◽  
Arf Excimer Laser

ABSTRACTA Fluorocarbon resin surface was selectively modified by irradiation with a ArF laser beam through a thin layer of NaAlO2, B(OH)3, or H2O solution to give a hydrophilic property. As a result, with low fluence, the surface was most effectively modified with the NaAlO2 solution among the three solutions. However, the contact angle in this case changed by 10 degrees as the fluence changed only 1mJ/cm2. When modifying a large area of the surface, high resolution displacement could not be achieved because the laser beam was not uniform in displacing functional groups. Thus, the laser fluence was successfully made uniform by homogenizing the laser beam; the functional groups were replaced on the fluorocarbon resin surface with high resolution, which was successfully modified to be hydrophilic by distributing the laser fluence uniformly.

Electron Holographic Nano-Characterization of Gold Catalyst at Interface

2002 ◽  
Vol 727 ◽  
Author(s):  
S. Ichikawa ◽  
T. Akita ◽  
M. Okumura ◽  
M. Haruta ◽  
K. Tanaka
Keyword(s):  
Contact Angle ◽  
Titanium Oxide ◽  
Gold Catalyst ◽  
Three Dimensional ◽  
High Resolution Electron Microscopy ◽  
Electron Holography ◽  
Gold Particles ◽  
Oxide Support ◽  
The Mean ◽  
A Charge

AbstractThe catalytic properties of nanostructured gold catalyst are known to depend on the size of the gold particles and to be activated when the size decreases to a few nanometers. We investigated the size dependence of the three-dimensional nanostructure on the mean inner potential of gold catalysts supported on titanium oxide using electron holography and high-resolution electron microscopy (HREM). The contact angle of the gold particles on the titanium oxide tended to be over 90° for gold particles with a size of over 5 nm, and below 90° for a size of below 2 nm. This decreasing change in the contact angle (morphology) acts to increase the perimeter and hence the area of the interface between the gold and titanium oxide support, which is considered to be an active site for CO oxidation. The mean inner potential of the gold particles also changed as their size decreased. The value of the inner potential of gold, which is approximately 25 V in bulk state, rose to over 40 V when the size of the gold particles was less than 2 nm. This phenomenon indicates the existence of a charge transfer at the interface between gold and titanium oxide. The 3-D structure change and the inner potential change should be attributed to the specific electronic structure at the interface, owing to both the “nano size effect” and the “hetero-interface effect.”

A NEW APPROACH TO INVESTIGATE CONTACT ANGLE HYSTERESIS

2018 ◽  
Author(s):  
Qiao Liu ◽  
Abbasali Abouei Mehrizi ◽  
Hao Wang
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
New Approach

Initial Contact Angle of the Foot Segment and GRF Components by the Gender Differences

2018 ◽  
Vol 57 (2) ◽  
pp. 625-633
Author(s):  
Sangheon Park ◽  
Sukhoon Yoon ◽  
Sang-Kyoon Park ◽  
Jiseon Ryu
Keyword(s):  
Gender Differences ◽  
Contact Angle ◽  
Initial Contact ◽  
Initial Contact Angle
Sign in / Sign up

Export Citation Format

Share Document