Response of tapered piles subjected to lateral loading

1999 ◽  
Vol 36 (1) ◽  
pp. 52-71 ◽  
Author(s):  
M Hesham El Naggar ◽  
Jin Qi Wei
Keyword(s):  
Large Scale ◽  
Bending Moment ◽  
Average Diameter ◽  
Confining Pressure ◽  
Lateral Loading ◽  
Cohesionless Soil ◽  
Lateral Loads ◽  
Moment Functions ◽  
Measured Strain ◽  
Displacement Transducers

Eighteen lateral loading tests were conducted on large-scale steel piles to establish the lateral behaviour of tapered piles in cohesionless soil. Three piles 1.52 m in length with different taper angles but the same average embedded diameter of 168 mm were installed in sand enclosed in a steel chamber 1.5 m in diameter and 1.445 m in depth. The soil chamber was lined with an air bladder so that sand inside the chamber could be pressurized to vary the confining pressure. The piles were instrumented with electrical resistance strain gauges and the horizontal pile movements at grade and the loading point were measured with displacement transducers. The bending-moment functions along the pile were calculated from the strain measurements by curve fitting the measured strain data. The soil resistance (p) and pile displacement (y) relationships were developed in the form of p-y curves by differentiating and integrating these bending-moment functions. It was found that tapered piles carried up to 77% more lateral loads than straight-sided-wall piles with the same average diameter. The maximum bending moment occurred in all piles at almost the same depth of one third of the embedded length of the pile. Hence, the cross section of tapered piles at the location of maximum bending moment was larger than that of straight-sided-wall piles, resulting in lower stresses in the pile. It was concluded that the tapered piles represent a more efficient distribution of the pile material and display better performance under lateral loading conditions.Key words: tapered piles, lateral response, p-y curves, modulus of subgrade reaction.

The loading behaviour of initially bent large scale laboratory piles in sand

1979 ◽  
Vol 16 (1) ◽  
pp. 43-58 ◽  
Author(s):  
S. F. Chan ◽  
T. H. Hanna
Keyword(s):  
Experimental Study ◽  
Transverse Shear ◽  
Axial Load ◽  
Large Scale ◽  
Applied Load ◽  
Bending Moment ◽  
Field Measurements ◽  
Cohesionless Soil ◽  
Single Piles ◽  
Pile Response

Field measurements indicate that piles are sometimes bent during driving. This paper reports on the results of an experimental study, at laboratory scale, of the behaviour of bent single piles when subjected to vertical loads. Varying degrees of bend were adopted for both friction and end bearing piles. The test piles, which were embedded in a cohesionless soil, were instrumented to measure the distributions of axial load, bending moment, and transverse shear along the pile shaft.The behaviour of bent piles was found to be far more complex than that of straight piles. For both the friction and end bearing piles, the response of the piles was governed by the degree of bend and the magnitudes of the moments and shears were significant at all levels of the applied load. An important feature in the pile response was the large residual moments and shears locked in the pile on unloading. The implications of the observed pile behaviour in relation to practice are discussed. A review of the reported cases of pile bending is also presented.

Centrifugal testing of laterally loaded piles in sand

1992 ◽  
Vol 29 (2) ◽  
pp. 208-216 ◽  
Author(s):  
M. Georgiadis ◽  
C. Anagnostopoulos ◽  
S. Saflekou
Keyword(s):  
Bending Moment ◽  
Cohesionless Soil ◽  
Soil Reaction ◽  
Lateral Loads ◽  
Laterally Loaded Piles ◽  
Nonlinear Springs ◽  
Different Types ◽  
Different Diameters ◽  
Laterally Loaded ◽  
Pile Length

Results of an investigation of the response of piles in sand, under lateral loads, are presented. Model piles of three different diameters and flexural stiffnesses were tested in a centrifuge apparatus to determine prototype pile behavior. The experimental results, consisting of pile head displacements and bending moment distributions along the pile length, were interpreted, analyzed, and compared with the results of several numerical analyses. The piles were treated as elastic beams on nonlinear springs, examining several different types of soil reaction relationship (p-y curves). A new p-y relationship was developed for piles in cohesionless soil which provided very satisfactory results. Key words : pile, sand, lateral loading, centrifuge, numerical analysis.

scholarly journals Transient Response of Bridge Piers to Structure Separation under Near-Fault Vertical Earthquake

2021 ◽  
Vol 11 (9) ◽  
pp. 4068
Author(s):  
Wenjun An ◽  
Guquan Song
Keyword(s):  
Large Scale ◽  
Bending Moment ◽  
Relative Displacement ◽  
Superposition Method ◽  
Longitudinal Displacement ◽  
Transient Wave ◽  
Vibration Period ◽  
Vertical Excitation ◽  
Mode Superposition Method ◽  
Main Girder

Given the possible separation problem caused by the double-span continuous beam bridge under the action of the vertical earthquake, considering the wave effect, the transient wave characteristic function method and the indirect mode superposition method are used to solve the response theory of the bridge structure during the earthquake. Through the example analysis, the pier bending moment changes under different vertical excitation periods and excitation amplitudes are calculated. Calculations prove that: (1) When the seismic excitation period is close to the vertical natural vibration period of the bridge, the main girder and the bridge pier may be separated; (2) When the pier has a high height, the separation has a more significant impact on the longitudinal displacement of the bridge, but the maximum relative displacement caused by the separation is random; (3) Large-scale vertical excitation will increase the number of partitions of the structure, and at the same time increase the vertical collision force between the main girder and the pier, but the effect on the longitudinal displacement of the form is uncertain; (4) When V/H exceeds a specific value, the pier will not only be damaged by bending, but will also be damaged by axial compression.

Comportement de pieux d'essais instrumentés sous charge horizontale

1993 ◽  
Vol 30 (1) ◽  
pp. 1-11
Author(s):  
R. Frank ◽  
H. Zervogiannis ◽  
S. Christoulas ◽  
V. Papadopoulos ◽  
N. Kalteziotis
Keyword(s):  
Pile Foundation ◽  
Bending Moment ◽  
Standard Penetration Test ◽  
American Petroleum Institute ◽  
Full Scale ◽  
Test Method ◽  
Cohesionless Soil ◽  
Penetration Test ◽  
Cohesionless Soils ◽  
Final Design

This paper describes the behaviour of two test piles (one bored and postgrouted and one simply bored, both 31.7 m long and 0.75 m in diameter) subjected to horizontal loads. These full-scale pile tests were carried out for the actual design of the pile foundation of a pier of the Evripos cable-stayed bridge. This bridge will link the Euboea Island to mainland Greece. The two piles have already been subjected to bearing capacity tests under axial loadings. The inclinometer measurements, taken during the present tests, yielded, in particular, the deformed shape of the piles as well as the bending moments. Conclusions could be drawn for the final design of the pile foundation with respect to horizontal loadings. Furthermore, various calculation methods using p–y reaction curves for cohesionless soils have been checked: the Ménard pressuremeter method, the method of the American Petroleum Institute recommendations, and the Standard penetration test method of Christoulas. These pile tests show that simple measurements, taken on construction sites, can yield interesting results on the actual behaviour of horizontally loaded piles. Key words : pile, horizontal loading, full-scale test, horizontal loads, bending moment, subgrade reaction modulus, p–y curve, cohesionless soil, Standard penetration test, pressuremeter test.

Effective rheology of a two-phase subduction shear zone: insights from numerical simple shear experiments and implications for subduction zone interfaces

2021 ◽  
Author(s):  
Paraskevi Io Ioannidi ◽  
Laetitia Le Pourhiet ◽  
Philippe Agard ◽  
Samuel Angiboust ◽  
Onno Oncken
Keyword(s):  
Simple Shear ◽  
Large Scale ◽  
Confining Pressure ◽  
Shear Zones ◽  
Dislocation Creep ◽  
Small Scale ◽  
Two Phase ◽  
Weak Phase ◽  
Pure Phases ◽  
Geodynamic Models

<p>Exhumed subduction shear zones often exhibit block-in-matrix structures comprising strong clasts within a weak matrix (mélanges). Inspired by such observations, we create synthetic models with different proportions of strong clasts and compare them to natural mélange outcrops. We use 2D Finite Element visco-plastic numerical simulations in simple shear kinematic conditions and we determine the effective rheology of a mélange with basaltic blocks embedded within a wet quartzitic matrix. Our models and their structures are scale-independent; this allows for upscaling published field geometries to km-scale models, compatible with large-scale far-field observations. By varying confining pressure, temperature and strain rate we evaluate effective rheological estimates for a natural subduction interface. Deformation and strain localization are affected by the block-in-matrix ratio. In models where both materials deform viscously, the effective dislocation creep parameters (A, n, and Q) vary between the values of the strong and the weak phase. Approaching the frictional-viscous transition, the mélange bulk rheology is effectively viscous creep but in the small scale parts of the blocks are frictional, leading to higher stresses. This results in an effective value of the stress exponent, n, greater than that of both pure phases, as well as an effective viscosity lower than the weak phase. Our effective rheology parameters may be used in large scale geodynamic models, as a proxy for a heterogeneous subduction interface, if an appropriate evolution law for the block concentration of a mélange is given.</p>

scholarly journals An Experimental Study of Horizontal Bearing Capacity of Vertical Steel Floral Tube Micropiles with Double Grouting

2018 ◽  
Vol 2018 ◽  
pp. 1-11
Author(s):  
Kaiyang Wang ◽  
Yanjun Shang
Keyword(s):  
Bearing Capacity ◽  
Large Scale ◽  
Slip Surface ◽  
Bending Moment ◽  
Shear Capacity ◽  
Soil Reinforcement ◽  
Scale Model ◽  
Soil Pressure ◽  
Floral Tube ◽  
Grouting Pressure

This paper examines the performance of a novel technology, vertical steel floral tube micropiles with double grouting. It is the combination of micropile technology and double grouting technology. A large-scale model tank was applied to impart horizontal bearing capacity, and the slope soil pressure and flexural performance of the micropile were investigated under four experimental conditions. The peak grouting pressure during the double grouting process was defined as the fracturing pressure of the double grouting, and it was positively correlated to the interval time between first grouting and secondary grouting. Compared with traditional grouting, double grouting increased the horizontal bearing capacity of the single micropile with the vertical steel floral tube by 24.42%. The horizontal bearing capacity was also 20.25% higher for the structure with three micropiles, compared with a 3-fold value of horizontal sliding resistance. In the test, the maximum bending moment acting on the pile above the sliding surface was located 2.0–2.5 m away from the pile top, and the largest negative bending moment acting on the pile below the slip surface was located 4.0 m away from the pile top. The ultimate bending moment of the single pile increased by 12.8 kN·m with double grouting, and the bending resistance increased by 96.2%. The experimental results showed that the double grouting technology significantly improved the horizontal bearing capacity of the micropile with the steel floral tube, and the soil reinforcement performance between piles was more pronounced. Also, the shear capacity and the flexural capacity were significantly improved compared with the original technology.

Large-scale triaxial tests of dense gravel material at low confining pressure

2012 ◽  
pp. 587-592
Author(s):  
S Lenart ◽  
J Koseki ◽  
T Sato ◽  
Y Miyashita ◽  
H Thang
Keyword(s):  
Large Scale ◽  
Confining Pressure ◽  
Triaxial Tests

scholarly journals Lateral Response of a Single Pile under Combined Axial and Lateral Cyclic Loading in Sandy Soil

2018 ◽  
Vol 4 (9) ◽  
pp. 1996 ◽  
Author(s):  
Muqdad Abdallah Kahribt ◽  
Jasim M. Abbas
Keyword(s):  
Lateral Displacement ◽  
Slenderness Ratio ◽  
Offshore Structures ◽  
Lateral Loading ◽  
Loading Conditions ◽  
Lateral Loads ◽  
Dense Sand ◽  
Lateral Response ◽  
Loading System ◽  
Vertical Displacements

According to practical situation, there have been limited investigations on the response of piles subjected to combined loadings especially when subjected to cyclic lateral loads. Those few studies led to contradictory results with regard to the effects of vertical loads on the lateral response of piles. Therefore, a series of experimental investigation into piles in dense sand subjected to combination of static vertical and cyclic lateral loading were conducted with instrumented model piles. The effect of the slenderness ratio (L/D) was also considered in this study (i.e. L/D= 25 and 40). In addition, a variety of two-way cyclic lateral loading conditions were applied to model piles using a mechanical loading system. One hundred cycles were used in each test to represent environmental loading such as offshore structures. It was found that under combined vertical and cyclic lateral loads the lateral displacement of piles decreased with an increase in vertical load whereas it causes large vertical displacements at all slenderness ratios. In addition, for all loading conditions the lateral, vertical (settlement and upward) displacements and bending moments increased as either the magnitude of cyclic load or the number of cycles increases. 

Uplift behaviour of tapered piles established from model tests

2000 ◽  
Vol 37 (1) ◽  
pp. 56-74 ◽  
Author(s):  
M Hesham El Naggar ◽  
Jin Qi Wei
Keyword(s):  
Load Transfer ◽  
Compressive Loading ◽  
Compressive Load ◽  
Tensile Load ◽  
Confining Pressure ◽  
Cohesionless Soil ◽  
Uplift Capacity ◽  
Experimental Modelling ◽  
Confining Pressures ◽  
Load Tests

Tapered piles have a substantial advantage with regard to their load-carrying capacity in the downward frictional mode. The uplift performance of tapered piles, however, has not been fully understood. This paper describes the results of an experimental investigation into the characteristics of the uplift performance of tapered piles. Three instrumented steel piles with different degrees of taper were installed in cohesionless soil and subjected to compressive and tensile load tests. The soil was contained in a steel soil chamber and pressurized using an air bladder to facilitate modelling the confining pressures pertinent to larger embedment depths. The results of this study indicated that the pile axial uplift capacity increased with an increase in the confining pressure for all piles examined in this study. The ratios of uplift to compressive load for tapered piles were less than those for straight piles of the same length and average embedded diameter. The uplift capacity of tapered piles was found to be comparable to that of straight-sided wall piles at higher confining pressure values, suggesting that the performance of actual tapered piles (with greater length) would be comparable to that of straight-sided wall piles. Also, the results indicated that residual stresses developed during the compressive loading phase and their effect were more significant on the initial uplift capacity of piles, and this effect was more pronounced for tapered piles in medium-dense sand.Key words: tapered piles, uplift, axial response, load transfer, experimental modelling.

Effect of Existing Building Walls on the Geotechnical Behavior of Foundation under Earthquake Loading

2021 ◽  
Vol 6 (4) ◽  
pp. 100-104
Author(s):  
M. N. Massoud Elsiragy
Keyword(s):  
Large Scale ◽  
Bending Moment ◽  
Horizontal Displacement ◽  
Scale Model ◽  
Earthquake Loading ◽  
Three Dimensional Model ◽  
Foundation Soil ◽  
Soil System ◽  
Existing Building ◽  
Building Walls

— Structure’s systems are subjected to additional loads due to earthquakes that may be produces progressive failures. The building illustrates dissimilar categories of failure mechanism for the minor to major earthquake conditions. These structures categorized to the most susceptible type of building has experienced serious hazard or even full failure for the period of seismic activities, therefore their investigation is a complex thing to do. Consequently, this research aims at studying the behaviour of large-scale model of structures constructed with and without brick walls under seismic conditions. The effect of building walls on the performance of the structure during earthquake loading is investigated numerically using PLAXIS 3D software. An eight story building with basement designed on a mat foundation is simulated as three-dimensional model in case of brick walls existing and without brick walls case. The effect of existence such wall building on the stability of foundation soil system is discussed in the form of lateral, horizontal deformation, and foundation acceleration. The studied showed that the reduction of extreme horizontal displacement and bending moment for building foundation with brick walls reached to 43%, and 68% respectively compared to the building without walls. The consideration of wall as filling for super structure significantly reduce the foundation acceleration by as much as 72% of its initial value, which lead to considerable effect of increasing the foundation stability.

Sign in / Sign up

Export Citation Format

Share Document