Bearing capacity of piles in layered soils. Part 2. Sand overlying clay

1978 ◽  
Vol 15 (2) ◽  
pp. 183-189 ◽  
Author(s):  
G. G. Meyerhof ◽  
V. V. R. N. Sastry
Keyword(s):  
Bearing Capacity ◽  
Field Data ◽  
Test Results ◽  
Layered Soils ◽  
Previous Part ◽  
Present Part ◽  
Sand Stratum

The previous Part 1 of this paper deals with the bearing capacity of piles penetrating through clay into sand. In the present Part 2 the case of piles penetrating into a sand stratum overlying clay is discussed. As the pile points approach the sand–clay interface, the piles may fail by punching through the sand into the underlying clay. Test results on instrumented model piles and field data are analysed to estimate the punching resistance of piles in layered soils.

Bearing capacity of piles in layered soils. Part 1. Clay overlying sand

1978 ◽  
Vol 15 (2) ◽  
pp. 171-182 ◽  
Author(s):  
G. G. Meyerhof ◽  
V. V. R. N. Sastry
Keyword(s):  
Bearing Capacity ◽  
Scale Effects ◽  
Cone Penetrometer ◽  
Test Results ◽  
Layered Soils ◽  
Driven Piles ◽  
Small Model ◽  
Sand Stratum ◽  
Pile Length ◽  
Shaft Friction

The paper summarizes investigations on jacked and driven piles in non-uniform soils consisting of clay and sand. Part 1 deals with the bearing capacity of piles penetrating through clay into sand whereas Part 2 discusses the case of piles in a sand stratum overlying clay. Preliminary tests on small model piles have been undertaken to study the effects on the point resistance of parameters such as the strength and thickness of a clay stratum, the strength ratio of soils in the two layers and the geometry of the layers. Based on these results, tests on a 76 mm diameter instrumented steel pile and a 36 mm diameter static cone penetrometer have been carried out for selected combinations of the variables involved.The test results are analysed to determine the influence of clay thickness and strength on the point resistance of piles in sand, expressed by a non-dimensional clay strength factor λ, and parameters influencing λ are discussed. The effect of layering on the shaft friction in sand and the radial stresses along the pile length are studied. The efficiency of small groups of model piles in layered soils is obtained. Field data are analysed, including scale effects, and simple design rules are suggested to estimate the bearing capacity of piles in layered soils.

scholarly journals Prediction of Grouting Penetration Height Along the Shaft of Base Grouted Pile

2019 ◽  
Vol 7 (7) ◽  
pp. 212
Author(s):  
Fang ◽  
Zhao ◽  
Tan ◽  
Qiu
Keyword(s):  
Bearing Capacity ◽  
Field Test ◽  
Iterative Procedure ◽  
Prediction Method ◽  
Test Results ◽  
Layered Soils ◽  
Pile Capacity ◽  
Pressure Grouting

Post-pressure grouting is an effective method to improve bearing capacity of ordinary bored cast-in-situ piles. The migration of the grout along the pile side is regarded as an important mechanism responsible for the improvement of the pile capacity. Research into the penetration height of the grout is of great important in evaluating the behavior of base grouted piles. In this paper, a prediction method of grouting penetration height along the shaft of the base grouted pile was proposed. Considering the balance and losses of the grout pressure during grouting, an iterative procedure was given to determine the penetration height of the grout in layered soils. Field test results were also provided to indicate the validity of the proposed method.

scholarly journals Prediction of Effects of Geogrid Reinforced Granular Fill on the Behaviour of Static Liquefaction

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
A. Hemalatha ◽  
N. Mahendran ◽  
G. Ganesh Prabhu
Keyword(s):  
Bearing Capacity ◽  
Load Test ◽  
Test Results ◽  
Plate Load Test ◽  
Large Size ◽  
Static Liquefaction ◽  
Granular Fill ◽  
Size Dimension ◽  
Subgrade Modulus ◽  
Different Thickness

The experimental investigation on the effects of granular fill and geogrid reinforced granular fill on the behaviour of the static liquefaction potential of the subsoil is reported in this study. A series of plate load test were carried out with different thickness of the granular fill, number of geogrid layers, and size/dimension of the footing. The test results were presented in terms of bearing capacity and subgrade modulus for the settlement ofδ10,δ15, andδ20. The experimental results revealed that the introduction of granular fill significantly increases the bearing capacity and effectively control the settlement behaviour of the footing. The introduction of geogrid in granular fill enhanced the Percentage of Control in Settlement and Bearing Capacity Ratio by a maximum of 328.54% and 203.41%, respectively. The introduction of geogrid in granular fill interrupts the failure zone of the granular fill and enhances the subgrade modulus of the footing by a maximum of 255.55%; in addition subgrade modulus of the footing was increased with an increase in the number of geogrid layers. Based on the test results it is suggested that the footing with large size has beneficial improvement on the reinforced granular fill.

Experimental Investigation for Horizontal Ultimate Bearing Capacity and Target Ductility Factor Improvement Results of the RC Column Reinforced by AFL with Damages

2014 ◽  
Vol 488-489 ◽  
pp. 497-500
Author(s):  
You Lin Zou ◽  
Pei Yan Huang
Keyword(s):  
Bearing Capacity ◽  
Ultimate Bearing Capacity ◽  
Test Results ◽  
Rc Columns ◽  
Static Test ◽  
Rc Column ◽  
Ductility Factor ◽  
Secant Stiffness ◽  
Function Relationship ◽  
Reversed Cyclic

Deem test results from the low reversed cyclic loading quasi-static test with 2 RC columns as the basic information of secant stiffness damage of the reference column and take use of the TMS instrument in the test to artificially make the damage percentage of secant stiffness of the RC column as 33%, 50% and 66%, 6 damaged columns in total; reinforce the 6 damaged columns and 2 undamaged ones under the same conditions with AFL, through quasi-static contrast test. Test results show that it is able to effectively boost horizontal ultimate bearing capacity and ductility deformability of the RC columns with AFL for reinforcement; besides, there is a linear function relationship between horizontal ultimate bearing capacity, target ductility factor, and damage percentage of secant stiffness.

Bearing Capacity Characteristic of Unsaturated Granular Soils

2011 ◽  
Vol 261-263 ◽  
pp. 989-993 ◽  
Author(s):  
Anuchit Uchaipichat ◽  
Ekachai Man Koksung
Keyword(s):  
Bearing Capacity ◽  
Matric Suction ◽  
Ultimate Bearing Capacity ◽  
Experimental Program ◽  
Granular Soils ◽  
Test Results ◽  
High Level ◽  
Unsaturated Granular Soils ◽  
Capacity Characteristic

An experimental program of laboratory bearing tests was performed to characterize the bearing capacity of foundation on unsaturated granular soils. All tests were performed by pushing a circular rod on the surface of compacted sand specimens with different values of matric suction until failure. The test results show an increase in ultimate bearing capacity with increasing matric suction at low suction value but a decrease in that at high level of suction. The comparisons between the test results and simulations using the expressions proposed in this paper are presented and discussed. Good agreements are achieved for all testing values of suction.

scholarly journals Tests and Analyses of Slotted-In Steel-Plate Connections in Composite Timber Shear Wall Panels

2017 ◽  
Vol 2017 ◽  
pp. 1-20
Author(s):  
Ulf Arne Girhammar ◽  
Bo Källsner
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Design Method ◽  
Shear Walls ◽  
Test Results ◽  
Horizontal Shear ◽  
Load Bearing Capacity ◽  
Wood Panel ◽  
Load Bearing ◽  
Plate Connections

The authors present an experimental and analytical study of slotted-in connections for joining walls in the Masonite flexible building (MFB) system. These connections are used for splicing wall elements and for tying down uplifting forces and resisting horizontal shear forces in stabilizing walls. The connection plates are inserted in a perimeter slot in the PlyBoard™ panel (a composite laminated wood panel) and fixed mechanically with screw fasteners. The load-bearing capacity of the slotted-in connection is determined experimentally and derived analytically for different failure modes. The test results show ductile postpeak load-slip characteristics, indicating that a plastic design method can be applied to calculate the horizontal load-bearing capacity of this type of shear walls.

Experimental Investigation of Stiffened Square CFST Columns under Axial Load

2014 ◽  
Vol 919-921 ◽  
pp. 1794-1800
Author(s):  
Xin Zhi Zheng ◽  
Xin Hua Zheng
Keyword(s):  
Experimental Investigation ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Axial Load ◽  
Local Buckling ◽  
Test Results ◽  
Tubular Columns ◽  
Economical Benefit ◽  
Steel Consumption ◽  
Cfst Columns

Abstract: 7 square steel tubular columns were tested to discuss the ultimate axial bearing capacity, ductility performance and the steel consumption under stiffened by steel belts and binding bars of different cross-sections. Test results indicate that only by increasing fewer amounts of steel usage, stiffened square CFST columns with binding bars can not only improve the overall effects of restraint and alleviate regional local buckling between the binding bars, but also improve the bearing capacity of concrete filled square steel tubular columns. The utility benefits and the economical benefit is considerable, deserving extensive use.

Research on mechanical behavior of L-shaped multi-cell concrete-filled steel tubular stub columns under axial compression

2018 ◽  
Vol 22 (2) ◽  
pp. 427-443 ◽  
Author(s):  
Jiepeng Liu ◽  
Hua Song ◽  
Yuanlong Yang
Keyword(s):  
Finite Element ◽  
Compressive Strength ◽  
Bearing Capacity ◽  
Thickness Ratio ◽  
Steel Plates ◽  
Test Results ◽  
Finite Element Program ◽  
Element Program ◽  
Compressive Strength Of Concrete ◽  
Stub Columns

A total of 11 L-shaped multi-cell concrete-filled steel tubular stub columns were fabricated and researched in axial compression test. The key factors of width-to-thickness ratio D/ t of steel plates in column limb and prism compressive strength of concrete fck were investigated to obtain influence on failure mode, bearing capacity, and ductility of the specimens. The test results show that the constraint effect for concrete provided by multi-cell steel tube cannot be ignored. The ductility decreases with the increase of width-to-thickness ratio D/ t of steel plates in column limb. The bearing capacity increases and the ductility decreases with the increase in prism compressive strength of concrete fck. A finite element program to calculate concentric load–displacement curves of L-shaped multi-cell concrete-filled steel tubular stub columns was proposed and verified by the test results. A parametric analysis with the finite element program was carried out to study the influence of the steel ratio α, steel yield strength fy, prism compressive strength of concrete fck, and width-to-thickness ratio D/ t of steel plates in column limb on the stiffness, bearing capacity and ductility. Furthermore, the design method of bearing capacity was determined based on mainstream concrete-filled steel tubular codes.

Sign in / Sign up

Export Citation Format

Share Document