Development and characterization of polysilicon emitter solar cells

1991 ◽  
Vol 69 (3-4) ◽  
pp. 479-482 ◽  
Author(s):  
G. Papadopoulos ◽  
L. P. Boivin ◽  
N. G. Tarr
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Amorphous Material ◽  
Chemical Vapor ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Float Zone ◽  
Pressure Chemical ◽  
20 Nm ◽  
Polysilicon Emitter

Solar cells with emitters consisting of a very thin (<20 nm) layer of silicon deposited in the polycrystalline phase overlaid with a thicker (≈100 nm) layer of recrystallized amorphous material were fabricated and characterized. Both layers were formed by low-pressure chemical vapor deposition with heavy in situ phosphorus doping. The highest temperature used in processing was 650 °C. Short-circuit current densities (Jsc) of 30 mA cm−2 combined with fill factors close to 0.8 were achieved under simulated 100 mW cm−2 AM1.5 illumination. Open-circuit voltages as high as 669 mV at 28 °C were obtained for cells formed on high-quality 0.1 Ω cm float zone substrates when Jsc was set to 32 mA cm−2.

scholarly journals Wide-Gap p-μc-Si1-xOx:H Films and Their Application to Amorphous Silicon Solar Cells

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Taweewat Krajangsang ◽  
Sorapong Inthisang ◽  
Aswin Hongsingthong ◽  
Amornrat Limmanee ◽  
Jaran Sritharathikhun ◽  
...  
Keyword(s):  
Solar Cells ◽  
Silicon Oxide ◽  
Short Circuit ◽  
Chemical Vapor ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Window Layer ◽  
Very High Frequency ◽  
Raman Scattering Spectroscopy ◽  
Wide Gap

Optimization of p-type hydrogenated microcrystalline silicon oxide thin films (p-μc-Si1-xOx:H) by very high frequency plasma enhanced chemical vapor deposition 40 MHz method for use as a p-layer of a-Si:H solar cells was performed. The properties of p-μc-Si1-xOx:H films were characterized by conductivity, Raman scattering spectroscopy, and spectroscopic ellipsometry. The wide optical band gap p-μc-Si1-xOx:H films were optimized by CO2/SiH4ratio and H2/SiH4dilution. Besides, the effects of wide-gap p-μc-Si1-xOx:H layer on the performance of a-Si:H solar cells with various optical band gaps of p-layer were also investigated. Furthermore, improvements of open circuit voltage, short circuit current, and performance of the solar cells by using the effective wide-gap p-μc-Si1-xOx:H were observed in this study. These results indicate that wide-gap p-μc-Si1-xOx:H is promising to use as window layer in a-Si:H solar cells.

Thermal Equilibrium Processes in a-Si:H Solar Cells

1995 ◽  
Vol 377 ◽  
Author(s):  
Jae-Hee Lee ◽  
Jae-Seog Koh ◽  
Jin Jang
Keyword(s):  
Solar Cells ◽  
Thermal Equilibrium ◽  
Short Circuit ◽  
Chemical Vapor ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Internal Electric Field ◽  
Equilibrium Processes ◽  
Current Voltage ◽  
Before And After

ABSTRACTHydrogenated amorphous silicon (a-Si:H) solar cells are prepared by plasma enhanced chemical vapor deposition (PECVD). Before quenching the solar cells, the short circuit current (Jsc), open circuit voltage (Voc), fill factor (F. F.) and conversion efficiency (η) are 17.79 mA/cm2, 0.79 V, 53.29, and 7.49 %, respectively. After thermal quenchine the solar cells from 200°C, Jsc, Voc, F. F., and η are 18.64 mA/cm2, 0.8 V, 53.79, and 8.02 %, respectively. We investigated the thermal equilibrium processes of each P, I, and N layers. Also, we obtained the dark current-voltage characteristics of a-Si:H solar cells before and after quenching. We analyze the results in terms of the change of the internal electric field in a-Si:H solar cells, caused by the shift of the Fermi level of P layer toward valence band.

Nanostructure Control of Si and Ge Quantum Dots Based Solar Cells Using Plasma Processes

2014 ◽  
Vol 783-786 ◽  
pp. 2022-2027 ◽  
Author(s):  
Masaharu Shiratani ◽  
Giichiro Uchida ◽  
Hyun Woong Seo ◽  
Daiki Ichida ◽  
Kazunori Koga ◽  
...  
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Electrical Power ◽  
Chemical Vapor ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Nanoparticles ◽  
Sensitized Solar Cells

We report characteristics of quantum dot (QD) sensitized solar cells using Si nanoparticles and Ge nanoparticles. Si nanoparticles were synthesized by multi-hollow discharge plasma chemical vapor deposition, whereas Ge nanoparticles were done by a radio frequency magnetron sputtering using Ar+H2under high pressure conditions. The electrical power generation from Si QDs and Ge QDs was confirmed. Si QD sensitized solar cells show an efficiency of 0.024%, fill factor of 0.32, short-circuit current of 0.75 mA/cm2and open-circuit voltage of 0.10 V, while Ge QD sensitized solar cells show an efficiency of 0.036%, fill factor of 0.38, short-circuit current of 0.64 mA/cm2and open-circuit voltage of 0.15 V.

scholarly journals Solar Cell Applications of Solution-Processed AgInGaSe2 Thin Films and Improved Properties by Sodium Doping

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 547
Author(s):  
Xianfeng Zhang ◽  
Qingxuan Sun ◽  
Maoxi Zheng ◽  
Zhuohua Duan ◽  
Yuehui Wang
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Critical Role ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Thin Layers ◽  
Sodium Doping ◽  
Cell Conversion ◽  
20 Nm

Binary nanoparticle inks comprising Ag2Se, In2Se3, and Ga2Se3 were fabricated via a wet ball-milling method and were further used to fabricate AgInGaSe2 (AIGS) precursors by sequentially spraying the inks onto a Mo-coated substrate. AIGS precursors were annealed under a Se atmosphere for 1 h at 570 °C. Na2Se thin layers of varying thicknesses (0, 5, 10, and 20 nm) were vacuum-evaporated onto the Mo layer prior to the AIGS precursors being fabricated to investigate the influence on AIGS solar cells. Sodium plays a critical role in improving the material properties and performance of AIGS thin-film solar cells. The grain size of the AIGS films was significantly improved by sodium doping. Secondary ion mass spectroscopy illustrated slight surficial sodium segregation and heavy sodium segregation at the AIGS/Mo interface. Double-graded band profiles were observed in the AIGS films. With the increase in Na2Se thickness, the basic photovoltaic characteristics of the AIGS solar cells were significantly improved. The highest solar cell conversion efficiency of 6.6% (open-circuit voltage: 775.6 mV, short-circuit current: 15.5 mA/cm2, fill factor: 54.9%, area: 0.2 cm2) was obtained when the Na2Se thickness was 20 nm.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Sign in / Sign up

Export Citation Format

Share Document