Electrical Contacts and Conductivity of MoS2 Layer Structures

1971 ◽  
Vol 49 (20) ◽  
pp. 2565-2571 ◽  
Author(s):  
A. Souder ◽  
D. E. Brodie
Keyword(s):  
Low Temperatures ◽  
Electrical Contact ◽  
Electrical Contacts ◽  
Experimental Results ◽  
Published Data ◽  
Anisotropic Layer ◽  
Layer Structures ◽  
Self Consistent ◽  
Mos2 Layer ◽  
Meaningful Data

The difficulty of making electrical contact to, and obtaining meaningful data from, strongly anisotropic layer structures is discussed and clarified for MoS2. An analysis of this anisotropy is presented and used to explain experimental results obtained from natural crystals of molybdenite.It is shown that annealed contacts on MoS2 make good electrical contact to the crystal by diffusing the contacting material parallel to the c axis and hence making contact to all of the layers. Just below room temperatures, activation energies [Formula: see text] parallel and [Formula: see text] perpendicular to the c axis are 0.04 to 0.08 eV but [Formula: see text] increases to between 0.08 and 0.12 eV below approximately 200 K, with [Formula: see text] at the low temperatures between 2 and 1.5 from sample to sample.The analysis is used to show that the published data for thick and thin crystals of MoTe2 can be made self-consistent.

Collision–induced absorption in gaseous methane at low temperatures

1986 ◽  
Vol 64 (7) ◽  
pp. 763-767 ◽  
Author(s):  
I. R. Dagg ◽  
A. Anderson ◽  
S. Yan ◽  
W. Smith ◽  
C. G. Joslin ◽  
...  
Keyword(s):  
Experimental Data ◽  
Low Temperatures ◽  
Low Frequency ◽  
Frequency Region ◽  
Experimental Results ◽  
Published Data ◽  
Frequency Range ◽  
Simple Method ◽  
Induced Absorption ◽  
Good Agreement

A recently developed theory for collision-induced absorption in methane is compared with experimental results over a wider spectral range and at lower temperatures than previously reported. The present experimental results covering the frequency range below 400 cm−1 exhibit good agreement with other recently published data. The theory shows excellent agreement with experiment in the low-frequency region below approximately 200 cm−1 but underestimates the experimental data somewhat at higher frequencies. Possible theoretical reasons for this discrepancy are given. The theory represents a simple method of obtaining a good estimate of the collision-induced absorption spectra of methane in this frequency region and for extrapolating to lower temperatures for which experimentation is not feasible. In addition, the moments α1 and γ1are compared with earlier determinations and indicate good agreement with the previously obtained values for the octupole and hexadecapole moments of methane.

Electrical contact performance of various electro-deposited graphene reinforced silver-based nanocomposites

2020 ◽  
Vol 62 (4) ◽  
pp. 401-407
Author(s):  
Ramazan Karslioglu ◽  
Lujain Al-Falahi
Keyword(s):  
Pulse Current ◽  
Electrical Contact ◽  
Reverse Current ◽  
Electrical Contacts ◽  
Test Device ◽  
Arc Erosion ◽  
Contact Test ◽  
Grain Sizes ◽  
Contact Erosion ◽  
Pulse Reverse

Abstract Silver and silver(Ag)-graphene(Gr) nanocomposite coatings were prepared via direct current, pulse current and pulse reverse current on copper electrical contacts for evaluating electrical contact performance. The effects of the addition of Gr and current types on microstructure, crystallographic orientation, mechanical properties and electrical contact performance were investigataed via a scanning electron microscope, an X-Ray diffractometer, microhardness test device and an electrical contact test device, respectively. The addition of Gr changed the Ag surface morphology and decreased grain sizes. Moreover, the addition of Gr significantly improved arc erosion resistivity and decreased the average working temperature during the contact test. In addition, pulse current and pulse reverse current provided a significant improvement in microhardness and electrical contact erosion resistance owing to increased embedded graphene amounts in silver layers.

Interaction Between Low Temperatures Spacers and Source Drain Extensions and Pockets for Both NMOS and PMOS of the 65 nm Node Technology

2006 ◽  
Vol 912 ◽  
Author(s):  
Nathalie Cagnat ◽  
Cyrille Laviron ◽  
Daniel Mathiot ◽  
Pierre Morin ◽  
Frédéric Salvetti ◽  
...  
Keyword(s):  
Oxide Layer ◽  
Hydrogen Content ◽  
Low Temperatures ◽  
Direct Contact ◽  
Fabrication Process ◽  
Experimental Results ◽  
The Other ◽  
Mos Transistors ◽  
Phosphorus Source ◽  
Activation Annealing

AbstractDuring the MOS transistors fabrication process, the source-drain extension areas are directly in contact with the oxide liner of the spacers stack. In previous works [1, 2, 3] it has been established that boron can diffuse from the source-drain extensions into the spacer oxide liner during the subsequent annealing steps, and that the amount of boron loss depends on the hydrogen content in the oxide, because it enhances B diffusivity in SiO2.In order to characterize and quantify the above phenomena, we performed test experiments on full sheet samples, which mimic either BF2 source-drain extensions over arsenic pockets implants, or BF2 pockets under arsenic or phosphorus source-drain extensions implants. Following the corresponding implants, the wafers were covered with different spacer stacks (oxide + nitride) deposited either by LPCVD, or PECVD. After appropriate activation annealing steps, SIMS measurements were used to characterize the profiles of the various dopants, and the corresponding dose loss was evaluated for each species.Our experimental results clearly evidence that LPCVD or PECVD spacer stacks have no influence on the arsenic profiles. On the other hand, phosphorus and boron profiles are affected. For boron profiles, each spacer type has a different influence. It is also shown that boron out-diffuses not only from the B doped source-drain extension in direct contact with the oxide layer, but also from the "buried" B pockets lying under n-doped source drain extension areas. All these results are discussed in term of the possible relevant mechanism.

Thermal and Electrical Conductivities of Sodium from 40 to 360 K

1972 ◽  
Vol 50 (12) ◽  
pp. 1386-1401 ◽  
Author(s):  
J. G. Cook ◽  
M. P. Van der Meer ◽  
M. J. Laubitz
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Low Temperatures ◽  
Characteristic Temperature ◽  
Published Data ◽  
Inelastic Electron ◽  
Conductivity Data ◽  
Electron Collisions ◽  
Electrical Conductivities ◽  
Flow Apparatus

We present data on the electrical and thermal resistivities and the thermopower of three pure Na specimens from 40 to 360 K. The measurements were made using a guarded longitudinal heat flow apparatus that had previously been calibrated with Au and Al. The specimens were placed in a vacuum environment using no solid inert liner.The electrical resistivity data indicate ΘR = 194 K. The thermal conductivity data show a 4% minimum near 70 K and an ice point value of 1.420 W/cm K. The reduced Lorenz function L/L0 agrees with published data at low temperatures but above 300 K levels off at approximately 0.91. On the basis of published data for liquid Na, L/L0 does not change by more than 3% at the melting point.The minimum in the thermal conductivity and a part of the high temperature deviations of L from L0 are tentatively ascribed to inelastic electron–phonon collisions having a characteristic temperature near that of longitudinal phonons. The possibility that electron–electron collisions further depress L at high temperatures is critically examined.

scholarly journals Integrated experimental-computational analysis of a liver-islet microphysiological system for human-centric diabetes research

2021 ◽  
Author(s):  
Belén Casas ◽  
Liisa Vilén ◽  
Sophie Bauer ◽  
Kajsa Kanebratt ◽  
Charlotte Wennberg Huldt ◽  
...  
Keyword(s):  
Glucose Metabolism ◽  
Computational Model ◽  
In Silico ◽  
Experimental Results ◽  
Published Data ◽  
Diabetes Research ◽  
Glucose Response ◽  
High Blood Glucose

Microphysiological systems (MPS) are powerful tools for emulating human physiology and replicating disease progression in vitro. MPS could be better predictors of human outcome than current animal models, but mechanistic interpretation and in vivo extrapolation of the experimental results remain significant challenges. Here, we address these challenges using an integrated experimental-computational approach. This approach allows for in silico representation and predictions of glucose metabolism in a previously reported MPS with two organ compartments (liver and pancreas) connected in a closed loop with circulating medium. We developed a computational model describing glucose metabolism over 15 days of culture in the MPS. The model was calibrated on an experiment-specific basis using data from seven experiments, where single-liver or liver-islet cultures were exposed to both normal and hyperglycemic conditions resembling high blood glucose levels in diabetes. The calibrated models reproduced the fast (i.e. hourly) variations in glucose and insulin observed in the MPS experiments, as well as the long-term (i.e. over weeks) decline in both glucose tolerance and insulin secretion. We also investigated the behavior of the system under hypoglycemia by simulating this condition in silico, and the model could correctly predict the glucose and insulin responses measured in new MPS experiments. Last, we used the computational model to translate the experimental results to humans, showing good agreement with published data of the glucose response to a meal in healthy subjects. The integrated experimental-computational framework opens new avenues for future investigations toward disease mechanisms and the development of new therapies for metabolic disorders.

scholarly journals Predicting the Tensile Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy via the Temperature-Dependent Crystal Plasticity Method

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3138
Author(s):  
Jun Zhang ◽  
Yang Wang ◽  
Peng Wang ◽  
Junhong Chen ◽  
Songlin Zheng
Keyword(s):  
Crystal Plasticity ◽  
Experimental Results ◽  
Uniaxial Tensile ◽  
Published Data ◽  
Initial Yield Stress ◽  
Polycrystal Plasticity ◽  
Different Temperatures ◽  
Polycrystalline Model ◽  
Critical Resolved Shear Stress ◽  
Relationship Of

Uniaxial tensile flow properties of a duplex Ti-6.6Al-3.3Mo-1.8Zr-0.29Si alloy in a temperature range from 213 K to 573 K are investigated through crystal plasticity modelling. Experimental results indicate that the initial yield stress of the alloy decreases as the temperature increases, while its work-hardening behavior displays temperature insensitivity. Considering such properties of the alloy, the dependence of the initial critical resolved shear stress (CRSS) on temperature is taken into account in the polycrystal plasticity modelling. Good coincidence is obtained between modelling and the experimental results. The determined values of CRSS for slip systems are comparable to the published data. The proposed polycrystalline model provides an alternative method for better understanding the microstructure–property relationship of α + β titanium alloys at different temperatures in the future.

Evaluation of Electrical Contact Material Stability on Mercuric Iodide

1993 ◽  
Vol 302 ◽  
Author(s):  
A. Y. Cheng
Keyword(s):  
Free Energy ◽  
Room Temperature ◽  
Electrical Contact ◽  
Radiation Detection ◽  
Electrical Contacts ◽  
Contact Material ◽  
Mercuric Iodide ◽  
Energy Data ◽  
Contact Materials ◽  
Temperature Radiation

ABSTRACTMercuric iodide detectors are leading candidates for room-temperature radiation detection applications. The inherently reactive nature of mercuric iodide limits the number of materials suitable for fabrication of electrical contacts. The theoretical stabilities of elemental contact materials on mercuric iodide were evaluated at 25°C. Additionally, the stabilities of transparent conductive compounds, for photodetector applications, were studied. Calculations were based on Gibbs free energy data, estimates and a series of hypothesized reactions with mercuric iodide. Leading candidate materials were identified and compared to experimental results.

X-Ray Diffraction and Reflectometry Investigation of Interdiffusion In Sputtered Niobium-Tungsten Bilayers

1999 ◽  
Vol 562 ◽  
Author(s):  
U. Welzel ◽  
P. Lamparter ◽  
E. J. Mittemeijer
Keyword(s):  
Diffusion Coefficients ◽  
Low Temperatures ◽  
Qualitative Evaluation ◽  
Diffraction Line ◽  
Published Data ◽  
Concentration Profiles ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray

ABSTRACTInterdiffusion in sputtered niobium(45nm)-tungsten(45nm) bilayers upon annealing at low temperatures (T<1000K) has been investigated using X-ray reflectometry and diffraction. The accompanying changes in macrostress and microstructure have been characterized by applying the X-ray diffraction sin2ψ T method and by qualitative evaluation of the diffraction line broadening, respectively. Annealing causes, besides interdiffusion, changes of macrostress and decrease of microstructural imperfection. Concentration profiles corresponding to diffusion lengths of only a few nanometers were determined by simulation of the measured reflectivity patterns. The values obtained for the diffusion coefficients are compared with corresponding values obtained by extrapolation from published data for bulk materials at much higher temperatures.

Tensile Behavior of Ti-5Al-2.5Sn Alloy at Low Temperatures and High Strain Rates

2019 ◽  
Vol 794 ◽  
pp. 135-141
Author(s):  
Bin Zhang ◽  
Yang Wang
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Low Temperatures ◽  
High Strain ◽  
Testing Temperature ◽  
Tensile Behavior ◽  
Experimental Results ◽  
Strain Rates ◽  
Increasing Temperature ◽  
Strain Hardening Rate

The mechanical responses of Ti-5Al-2.5Sn alloy at low temperatures were investigated under quasi-static and dynamic tensile loads using MTS system and SHTB system, respectively. Tensile stress-strain curves were obtained over the temperature range of 153 to 298K and the rate range of 0.001 to 1050 s-1. Experimental results indicate that the tensile behavior of Ti-5Al-2.5Sn alloy is dependent on strain rate and temperature. Yield stress and flow stress increase with increasing strain rate and decrease with increasing temperature. Results also indicate that strain hardening rate of Ti-5Al-2.5Sn alloy is lower at high strain rate, while strain hardening rate varies little with testing temperature. The Khan-Huang-Liang constitutive model was chosen to characterize the tensile responses of Ti-5Al-2.5Sn alloy at low temperatures and different strain rates. The model results coincide well with the experimental results within the tested temperature and rate ranges.

Sign in / Sign up

Export Citation Format

Share Document