Seismic loading for buildings with setbacks

1994 ◽  
Vol 21 (5) ◽  
pp. 863-871 ◽  
Author(s):  
C. M. Wong ◽  
W. K. Tso
Keyword(s):  
Dynamic Analysis ◽  
Fundamental Mode ◽  
Load Distribution ◽  
Static Load ◽  
Seismic Loading ◽  
Seismic Load ◽  
Base Shear ◽  
Reasonable Estimate ◽  
Equivalent Static Load ◽  
Irregular Buildings

Dynamic analysis is in general accepted as the best method to obtain the seismic load distribution for buildings with a setback. However, most building codes require the base shear obtained by dynamic analysis to be calibrated by the static base shear obtained using the code's equivalent static load procedure. In obtaining the code static base shear, two issues often arise among the design professionals. First, it is unclear whether the code static base shear is applicable for buildings with setbacks because the period prescribed by the code to be used in the base shear formula is in general not pertinent to buildings with setbacks. Second, it is uncertain whether the higher mode period should be used in computing the base shear when the modal weight of a higher mode is larger than that of the fundamental mode — a case often encountered in designing buildings with setbacks. This paper is an attempt to resolve the above issues. For the first issue, modification factors were derived for adjusting the code period formula so that it can provide a more reasonable estimate for the period of a building with a setback. For the second issue, it was demonstrated in this paper that for cases where the modal weight of a higher mode is larger than that of the fundamental mode, using the higher mode period for base shear calculation will result in unnecessarily conservative design. Key words: earthquake, seismic, irregular buildings, setback, dynamic analysis.

Determination of seismic design forces by equivalent static load method

2003 ◽  
Vol 30 (2) ◽  
pp. 287-307 ◽  
Author(s):  
JagMohan Humar ◽  
Mohamed A Mahgoub
Keyword(s):  
Seismic Design ◽  
Static Load ◽  
Base Shear ◽  
Uniform Hazard Spectra ◽  
Uniform Hazard Spectrum ◽  
Higher Mode Effects ◽  
Mode Effects ◽  
Equivalent Static Load ◽  
Adjustment Factors ◽  
Mode Vibration

In the proposed 2005 edition of the National Building Code of Canada (NBCC), the seismic hazard will be represented by uniform hazard spectra corresponding to a 2% probability of being exceeded in 50 years. The seismic design base shear for use in an equivalent static load method of design will be obtained from the uniform hazard spectrum for the site corresponding to the first mode period of the building. Because this procedure ignores the effect of higher modes, the base shear so derived must be suitably adjusted. A procedure for deriving the base shear adjustment factors for different types of structural systems is described and the adjustment factor values proposed for the 2005 NBCC are presented. The adjusted base shear will be distributed across the height of the building in accordance with the provisions in the current version of the code. Since the code-specified distribution is primarily based on the first mode vibration shape, it leads to an overestimation of the overturning moments, which should therefore be suitably adjusted. Adjustment factors that must be applied to the overturning moments at the base and across the height are derived for different structural shapes, and the empirical values for use in the 2005 NBCC are presented.Key words: uniform hazard spectrum, seismic design base shear, equivalent static load procedure, higher mode effects, base shear adjustment factors, distribution of base shear, overturning moment adjustment factors.

Seismic load distribution in buildings with eccentric setback

1994 ◽  
Vol 21 (1) ◽  
pp. 50-62 ◽  
Author(s):  
W. K. Tso ◽  
Shu Yao
Keyword(s):  
Dynamic Analysis ◽  
Key Words ◽  
Wide Class ◽  
Load Distribution ◽  
Lateral Loading ◽  
Building Code ◽  
Seismic Load ◽  
Load Distributions ◽  
Static Approach ◽  
Code Procedure

A study is carried out to evaluate the seismic load distribution in buildings with eccentric setback subjected to lateral loading in a direction perpendicular to the setback. Such loading causes both translational and torsional deformations. Since buildings with eccentric setback possess significant irregularities both height-wise and plan-wise, both the static and the dynamic approaches are used in this study to examine the limitations of the static approach when applied to this class of structures. It is shown that the static approach cannot simulate the higher modal contribution, nor can it simulate the inertial floor torques caused by the first mode of vibration. Consequently, the static approach leads to an underestimation of edge frame shears. However, by modifying the static approach as is done in the Canadian code (National Building Code of Canada, 1990) one can obtain load distributions in eccentric buildings that are similar to that using dynamic analysis. Based on the work of Goel and Chopra, it is further shown that implementation of the Canadian code procedure for seismic load distribution involving torsion can be simplified greatly. As a result, this procedure can be implemented efficiently in design offices to cover a wide class of buildings, including buildings with eccentric setbacks. Key words: seismic, buildings, torsion, setback, irregularity, code.

Dynamic Analysis of PK Section Girder of Cable Stayed Bridges

2014 ◽  
Vol 638-640 ◽  
pp. 1018-1023
Author(s):  
Li Ying Nie ◽  
Jiang Fei Li ◽  
Zhe Pan
Keyword(s):  
Dynamic Response ◽  
Dynamic Analysis ◽  
Static Load ◽  
Bending Moment ◽  
Element Model ◽  
Internal Force ◽  
Seismic Load ◽  
Negative Bending ◽  
Cable Stayed Bridges ◽  
Load Impact

Pasco-Kennewick (PK) section girder is widely used in the concrete cable stayed bridges with double cable planes, because of its excellent mechanical properties. By created the double girder finite element model, this paper analyzed the dynamic response of one concrete cable stayed bridges with PK section and the dynamic response of the diaphragms. According to the results of the analysis, the diaphragms which near the auxiliaries’ pier s and pylons generated large seismic internal force under the seismic load, and it is account for large proportion when compared with the static load. So, single-girder model can not satisfy the requests for the dynamic analysis of the girder. Due to the cross beams generated large positive, negative bending moment when seismic load impact, we must take notice of strengthening reinforcement in diaphragms. Especially the reinforcement for the negative bending moment, so as to meet the requests for the anti-seismic.

Inferring hillslope response under seismic loading and rainfall: A case study from the SE Carpathian, Romania

2021 ◽  
Author(s):  
Vipin Kumar ◽  
Léna Cauchie ◽  
Anne-Sophie Mreyen ◽  
Philippe Cerfontaine ◽  
Mihai Micu ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Slope Stability ◽  
Surface Runoff ◽  
Dynamic Condition ◽  
Seismic Loading ◽  
Seismic Stability ◽  
Seismic Load ◽  
Stability Evaluation ◽  
Rainfall Events ◽  
Year 2000

<p>Seismic stability evaluation plays a crucial role in landslide disaster risk reduction. Related modeling also has to consider the potential influences of the rainfall on the hillslopes. This study aims at understanding the relative influence of the seismic loading and extreme cumulative rainfall on a massive active landslide in the seismically active Vrancea-Buzau region of the Romanian Carpathians (45° 30' 23" N, 26° 25' 05" E). This region has been subjected to more than 700 earthquakes (M>4) events with the highest magnitude of 7.2 (M<sub>w</sub>) during the year 1960-2019. Rainfall data of the year 2000-2019 revealed the occurrence of relatively intense rainfall events, especially during the last ten years. The landslide has an aerial dimension of ~9.1 million m². It hosts the small village of Varlaam at the toe along the Bisca River. The slope (with an average gradient of 15-20°) is covered by shrubs and scattered trees near its borders and is relatively barren in the central part. Shales with some intercalated sandstone layers belonging to the Miocene thrust belt constitute the rocks of the slope.   </p><p>A first survey involving the multi-station array and related Horizontal-to-Vertical noise Spectral Ratio (HVSR) measurements was completed in summer 2019. The findings of the HVSR were processed using the inversion process to infer the shear wave velocity distribution with depth and to detect the sliding surface of the landslide. These velocities were further used to estimate the geotechnical properties of the subsurface using the empirical equations. The HVSR based depth profiles and the Unmanned Air Vehicle based topographic information were used to take four 2D slope sections. These sections were considered for 2D discrete element modeling based stability evaluation under static and dynamic condition along with sensitivity analysis. Static simulation was used to determine the Factor of Safety (FS) using the shear strength reduction approach. Ricker wavelet was used as input seismic load in the dynamic simulation. Potential run-out and flow characteristics of the slope material were explored using the Voellmy rheology based RAMMS software. The relationship between rainfall, surface runoff, and soil moisture was also explored to understand the hydrogeological influence on slope stability.</p><p>Though the slope reveals meta-stability (1.0<FS<2.0) condition under static loading, displacement in the soil reaches up to 1.5 m that further increases to 2.8 m under dynamic loading. According to the topographic characteristics of the slope and to the presence of landslide material or intact bedrock near the surface, acceleration along the slope reaches a Peak Ground Acceleration in the range of 0.6 to 1.3g. Eight extreme rainfall events (>50mm/24 hours) during the year 2000-2019 are noted to temporally coincide with enhanced surface runoff and increased soil moisture in the region. Debris flow runout modeling indicated that the slope material may attain a maximum flow height and flow velocity of 13±0.8 m and 5±0.5 m/sec, respectively, along the river channel.</p><p><strong>Keywords: </strong>Landslide;<strong> </strong>Earthquake; Slope stability; Runout; SE Carpathian</p>

scholarly journals Seismic Performance of Multistorey RC Frame Building With The Soft Storey and Masonry Infill

2021 ◽  
pp. 650-656
Author(s):  
Kugan K ◽  
Mr. Nandha Kumar P ◽  
Premalath J
Keyword(s):  
Time History ◽  
Seismic Loading ◽  
Rc Frame ◽  
Base Shear ◽  
Maximum Displacement ◽  
Soft Storey ◽  
Masonry Infills ◽  
Frame Building ◽  
History Analysis ◽  
Rc Frame Building

In this study, four geometrically similar frames having different configurations of masonry infills, has been investigated. In this article attempts are made to explain the factors that impact the soft storey failure in a building are compared with different type of infill. That is Four models like RC bare frame, RC frame with brick mansonry infill, RC frame with brick infill in all the storeys exept the firstsoft storey, RC frame with inverted V bracing in the soft storey. Time history analysis has been carried out for a G+8 multistoried building to study the soft storey effect at different floor levels using E tabs software. The behavior of RC framed building with soft storey under seismic loading has been observed in terms of maximum displacement ,maximum storey drift, base shear and storey stiffness as considered structure.

scholarly journals Numerical Simulation of Dynamic Response and Evaluation of Flexural Damage of RC Columns under Horizontal Impact Load

2021 ◽  
Vol 11 (23) ◽  
pp. 11223
Author(s):  
Bin Hu ◽  
Jian Cai ◽  
Jiabin Ye
Keyword(s):  
Static Load ◽  
Impact Load ◽  
Bending Moment ◽  
Internal Force ◽  
Displacement Curve ◽  
Fe Model ◽  
Damage State ◽  
Rc Columns ◽  
Equivalent Static Load ◽  
The Impact

By using the ABAQUS finite element (FE) model, which has been verified by experiments, the deformation and internal force changes of RC columns during the impact process are investigated, and a parametric analysis is conducted under different impact kinetic energies Ek. According to the development path of the bottom bending moment-column top displacement curve under impact, the member is in a slight damage state when the curve rebounds before reaching the peak and in a moderate or severe damage state when the curve exceeds the peak, in which case the specific damage state of the member needs to be determined by examining whether there is a secondary descending stage in the curve. Accordingly, a qualitative method for evaluating the bending failure of RC column members under impact is obtained. In addition, the damage state of RC columns under impact can also be quantitatively evaluated by the ratio of the equivalent static load Feq and the ultimate static load-bearing capacity Fsu.

scholarly journals Comparison of Numerical Analyses with a Static Load Test of a Continuous Flight Auger Pile

2014 ◽  
Vol 22 (4) ◽  
pp. 1-10 ◽  
Author(s):  
Michal Hoľko ◽  
Jakub Stacho
Keyword(s):  
Load Distribution ◽  
Static Load ◽  
Numerical Models ◽  
Load Test ◽  
Numerical Analyses ◽  
Static Load Test ◽  
Material Models ◽  
The Common ◽  
Constitutive Material ◽  
The Impact

Abstract The article deals with numerical analyses of a Continuous Flight Auger (CFA) pile. The analyses include a comparison of calculated and measured load-settlement curves as well as a comparison of the load distribution over a pile's length. The numerical analyses were executed using two types of software, i.e., Ansys and Plaxis, which are based on FEM calculations. Both types of software are different from each other in the way they create numerical models, model the interface between the pile and soil, and use constitutive material models. The analyses have been prepared in the form of a parametric study, where the method of modelling the interface and the material models of the soil are compared and analysed. Our analyses show that both types of software permit the modelling of pile foundations. The Plaxis software uses advanced material models as well as the modelling of the impact of groundwater or overconsolidation. The load-settlement curve calculated using Plaxis is equal to the results of a static load test with a more than 95 % degree of accuracy. In comparison, the load-settlement curve calculated using Ansys allows for the obtaining of only an approximate estimate, but the software allows for the common modelling of large structure systems together with a foundation system.

The Force Analysis of Anchor Anti-Slide Pile in Slope Reinforcement under Seismic Load

2015 ◽  
Vol 777 ◽  
pp. 148-153
Author(s):  
Hui Ding ◽  
Jie Chen ◽  
Li Song
Keyword(s):  
Dynamic Analysis ◽  
Seismic Wave ◽  
Contact Stress ◽  
Dynamic Performance ◽  
Bending Moment ◽  
Dynamic Contact ◽  
Design Parameters ◽  
Seismic Load ◽  
Slope Reinforcement ◽  
Earthquake Action

The force affect factors of anchor anti-slide pile in slope reinforcement under seismic load are studied in this paper. First of all, the method of dynamic analysis is introduced in FLAC3D. At the same time, seismic wave is selected in seismic dynamic analysis. Then, the sensitivity influence of anti-slide pile design parameters on dynamic contact stress, shear force and dynamic bending moment is analyzed by applying the seismic wave, giving the most significant effect factors of the dynamic contact stress and dynamic moment. In the end, the distribution regular of the contact force and the pile body stress under earthquake action is analyzed by selecting a case, laying a theoretical foundation for the further study of the dynamic performance of the reinforced slope.

Sign in / Sign up

Export Citation Format

Share Document