Analysis of wood diaphragms and trusses. Part II: Truss-plate connections

1977 ◽  
Vol 4 (3) ◽  
pp. 353-362 ◽  
Author(s):  
Ricardo O. Foschi
Keyword(s):  
High Density ◽  
Experimental Results ◽  
Single Tooth ◽  
Nonlinear Character ◽  
Connected Area ◽  
Plate Connections ◽  
Actual Shape ◽  
Deformation Relationship ◽  
Good Agreement ◽  
Wood Diaphragms

An analysis of truss-plate connections is presented, taking into account the nonlinear character of the load–deformation relationship. The connection is considered as ‘continuous’ because of the high density of teeth, and connector properties are derived from those for a single tooth. Parameters considered in the analysis include the actual shape of the connected area, gaps between connected members, the buckling capacity of the plate, and its yielding in tension and shear. Good agreement is shown in a comparison between theoretical and experimental results using a single connection under eccentric loading.

scholarly journals Solution of Spur Gear Meshing Stiffness and Analysis of Degradation Characteristics

Mechanika ◽  
2020 ◽  
Vol 26 (2) ◽  
pp. 153-160 ◽  
Author(s):  
Hongchao Ji ◽  
Jianwei Dong ◽  
Weichi Pei ◽  
Haiyang Long ◽  
Jing Chu
Keyword(s):  
Mechanical Test ◽  
Gear Tooth ◽  
Spur Gear ◽  
Experimental Results ◽  
Test Bed ◽  
Meshing Stiffness ◽  
Single Tooth ◽  
Double Teeth ◽  
Degree Of Degradation ◽  
Good Agreement

The computational model of spur gear meshing stiffness is established by using the hypothesis of cantilever beam of the gear. The meshing stiffness of spur gear is calculated by analytical method, and the distributional curve of meshing stiffness is obtained by comparison with FEM. Experimental verification of simulated results is performed by mechanical test-bed of closed flow. The experimental results show that the simulation results are in good agreement with the experimental results. Based on the FEM models of gear tooth with cracks of different lengths, the comparison between degradation trends in different meshing regions that shows that the degree of degradation in a single tooth meshing area is much higher than in a double teeth meshing region. In the FEM models of gear tooth with cracks of different lengths, the stiffness degradation rate of the double tooth indentation area increases first and then decreases, and the crack length is most obvious between 4 and 8 mm. 

Nanoindentation of a Deformable Substrate Covered by Patterned Nanodot Asperities

2009 ◽  
Author(s):  
Hengyu Wang ◽  
Min Zou ◽  
Robert L. Jackson ◽  
Preston R. Larson ◽  
Matthew B. Johnson
Keyword(s):  
Silicon Substrate ◽  
Experimental Studies ◽  
Indentation Load ◽  
Spherical Indenter ◽  
Experimental Results ◽  
Contact Model ◽  
Asperity Contact ◽  
Deformation Relationship ◽  
Repetitive Pattern ◽  
Good Agreement

This paper presents numerical and experimental studies of nanoindentation of a silicon substrate covered by patterned Ni nanodot asperities. A multi-asperity contact model was developed in this study to simulate the contact between a spherical indenter and the Ni nanodot asperities. In this model, the silicon substrate is considered to be deformable and the nanodots are allowed to interact with each other through the deformation of the substrate. The load-deformation relationship predicted by the model was found to be in good agreement with the experimental results. This model can also be used to predict indentation load-deformation relationships of a deformable substrate covered by nanodots with known size and location distributions, but not necessarily following a repetitive pattern.

Inducing Frictional Force to Enhance the Transient Response in Beams

2019 ◽  
Vol 22 (2) ◽  
pp. 88-93
Author(s):  
Hamed Khanger Mina ◽  
Waleed K. Al-Ashtrai
Keyword(s):  
Numerical Analysis ◽  
Transient Response ◽  
Frictional Force ◽  
Damping Ratio ◽  
Experimental Results ◽  
Damping Capacity ◽  
Tightening Force ◽  
Contact Areas ◽  
Good Agreement ◽  
Ansys Workbench

This paper studies the effect of contact areas on the transient response of mechanical structures. Precisely, it investigates replacing the ordinary beam of a structure by two beams of half the thickness, which are joined by bolts. The response of these beams is controlled by adjusting the tightening of the connecting bolts and hence changing the magnitude of the induced frictional force between the two beams which affect the beams damping capacity. A cantilever of two beams joined together by bolts has been investigated numerically and experimentally. The numerical analysis was performed using ANSYS-Workbench version 17.2. A good agreement between the numerical and experimental results has been obtained. In general, results showed that the two beams vibrate independently when the bolts were loosed and the structure stiffness is about 20 N/m and the damping ratio is about 0.008. With increasing the bolts tightening, the stiffness and the damping ratio of the structure were also increased till they reach their maximum values when the tightening force equals to 8330 N, where the structure now has stiffness equals to 88 N/m and the damping ratio is about 0.062. Beyond this force value, increasing the bolts tightening has no effect on stiffness of the structure while the damping ratio is decreased until it returned to 0.008 when the bolts tightening becomes immense and the beams behave as one beam of double thickness.

PHOTOINDUCED NONLINEAR OCTUPOLAR POLARIZATION: TRANSIENT AND PERMANENT REGIMES

1996 ◽  
Vol 05 (04) ◽  
pp. 653-670 ◽  
Author(s):  
CÉLINE FIORINI ◽  
JEAN-MICHEL NUNZI ◽  
FABRICE CHARRA ◽  
IFOR D.W. SAMUEL ◽  
JOSEPH ZYSS
Keyword(s):  
Theoretical Analysis ◽  
Second Harmonic ◽  
Experimental Results ◽  
Polar Field ◽  
Rotational Spectrum ◽  
Dual Frequency ◽  
One Dimensional ◽  
Ethyl Violet ◽  
Disperse Red 1 ◽  
Good Agreement

An original poling method using purely optical means and based on a dual-frequency interference process is presented. We show that the coherent superposition of two beams at fundamental and second-harmonic frequencies results in a polar field with an irreducible rotational spectrum containing both a vector and an octupolar component. This enables the method to be applied even to molecules without a permanent dipole such as octupolar molecules. After a theoretical analysis of the process, we describe different experiments aiming at light-induced noncentrosymmetry performed respectively on one-dimensional Disperse Red 1 and octupolar Ethyl Violet molecules. Macroscopic octupolar patterning of the induced order is demonstrated in both transient and permanent regimes. Experimental results show good agreement with theory.

scholarly journals Millisecond lattice gasification for high-density CO2- and O2-sieving nanopores in single-layer graphene

2021 ◽  
Vol 7 (9) ◽  
pp. eabf0116
Author(s):  
Shiqi Huang ◽  
Shaoxian Li ◽  
Luis Francisco Villalobos ◽  
Mostapha Dakhchoune ◽  
Marina Micari ◽  
...  
Keyword(s):  
Single Layer ◽  
High Density ◽  
Single Layer Graphene ◽  
Pore Density ◽  
Vacancy Defects ◽  
Carbon Gasification ◽  
Layer Graphene ◽  
Gas Molecules ◽  
Good Agreement

Etching single-layer graphene to incorporate a high pore density with sub-angstrom precision in molecular differentiation is critical to realize the promising high-flux separation of similar-sized gas molecules, e.g., CO2 from N2. However, rapid etching kinetics needed to achieve the high pore density is challenging to control for such precision. Here, we report a millisecond carbon gasification chemistry incorporating high density (>1012 cm−2) of functional oxygen clusters that then evolve in CO2-sieving vacancy defects under controlled and predictable gasification conditions. A statistical distribution of nanopore lattice isomers is observed, in good agreement with the theoretical solution to the isomer cataloging problem. The gasification technique is scalable, and a centimeter-scale membrane is demonstrated. Last, molecular cutoff could be adjusted by 0.1 Å by in situ expansion of the vacancy defects in an O2 atmosphere. Large CO2 and O2 permeances (>10,000 and 1000 GPU, respectively) are demonstrated accompanying attractive CO2/N2 and O2/N2 selectivities.

scholarly journals Comparison of Experimental and Numerical Transient Drop Deformation during Transition through Orifices in High-Pressure Homogenizers

2021 ◽  
Vol 5 (3) ◽  
pp. 32
Author(s):  
Benedikt Mutsch ◽  
Peter Walzel ◽  
Christian J. Kähler
Keyword(s):  
High Pressure ◽  
Visual Analysis ◽  
Imaging Technique ◽  
Extensional Flow ◽  
Droplet Breakup ◽  
Experimental Results ◽  
Drop Deformation ◽  
Droplet Deformation ◽  
Shadow Imaging ◽  
Good Agreement

The droplet deformation in dispersing units of high-pressure homogenizers (HPH) is examined experimentally and numerically. Due to the small size of common homogenizer nozzles, the visual analysis of the transient droplet generation is usually not possible. Therefore, a scaled setup was used. The droplet deformation was determined quantitatively by using a shadow imaging technique. It is shown that the influence of transient stresses on the droplets caused by laminar extensional flow upstream the orifice is highly relevant for the droplet breakup behind the nozzle. Classical approaches based on an equilibrium assumption on the other side are not adequate to explain the observed droplet distributions. Based on the experimental results, a relationship from the literature with numerical simulations adopting different models are used to determine the transient droplet deformation during transition through orifices. It is shown that numerical and experimental results are in fairly good agreement at limited settings. It can be concluded that a scaled apparatus is well suited to estimate the transient droplet formation up to the outlet of the orifice.

Simulation of Sphere’s Motion Induced by Shock Waves

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Dan Igra ◽  
Ozer Igra ◽  
Lazhar Houas ◽  
Georges Jourdan
Keyword(s):  
Shock Waves ◽  
Drag Coefficient ◽  
Drag Force ◽  
Stationary Flow ◽  
Experimental Results ◽  
Experimental Findings ◽  
Sphere Drag ◽  
Simulation Scheme ◽  
Good Agreement

Simulations of experimental results appearing in Jourdan et al. (2007, “Drag Coefficient of a Sphere in a Non-Stationary Flow: New Results,”Proc. R. Soc. London, Ser. A, 463, pp. 3323–3345) regarding acceleration of a sphere by the postshock flow were conducted in order to find the contribution of the various parameters affecting the sphere drag force. Based on the good agreement found between present simulations and experimental findings, it is concluded that the proposed simulation scheme could safely be used for evaluating the sphere’s motion in the postshock flow.

Viscoelastic Deformation of PC/ABS Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 1229-1232
Author(s):  
Z.N. Yin ◽  
L.F. Fan ◽  
Tie Jun Wang
Keyword(s):  
Dynamic Mechanical Analysis ◽  
Relaxation Modulus ◽  
Mechanical Analysis ◽  
Experimental Results ◽  
Viscoelastic Deformation ◽  
Dynamic Mechanical ◽  
Storage And Loss Moduli ◽  
Static Relaxation ◽  
Comparison Of The Results ◽  
Good Agreement

Dynamic Mechanical Analysis (DMA) and static relaxation tests are carried out to study the viscoelastic deformation of PC/ABS alloy with blending ratio of PC to ABS being 50/50. A modified approach is developed to calculate the relaxation modulus of PC/ABS alloy from the DMA experimental results of storage and loss moduli. Comparison of the results obtained from DMA and static relaxation tests is presented and good agreement is found.

Influence of the Morphology on the Optical Properties of Nanocermet Films: A Renormalization Approach

1990 ◽  
Vol 195 ◽  
Author(s):  
S. Berthier ◽  
K. Driss-Khodja
Keyword(s):  
Optical Properties ◽  
Critical Exponents ◽  
Inhomogeneous Media ◽  
Experimental Results ◽  
Percolation Transition ◽  
Position Space ◽  
Renormalization Approach ◽  
2D And 3D ◽  
Good Agreement ◽  
Effective Medium Models

ABSTRACTIn order to take into account the actual morphology of the inhomogeneous media, we have developed, effective medium models based on a 2D and 3D position space renormalization /1,2/. These models predict the dipolar resonance and the percolation transition with critical exponents in good agreement with theoretical values and fairly reproduce most of the experimental results, whatever the concentration is. Further more, this allows a valuable comparison of the predictions of our models when applied on different lattices like real digitized TEM of cermet films or randomly occupied lattices.

Experimental Study and Finite Analysis on Flexural Capacity of Laminated Glass

2011 ◽  
Vol 243-249 ◽  
pp. 258-262
Author(s):  
Jun Chen ◽  
Jia Lv ◽  
Qi Lin Zhang ◽  
Zhi Xiong Tao ◽  
Jun Chen
Keyword(s):  
Experimental Results ◽  
Laminated Glass ◽  
Test Results ◽  
Design Code ◽  
Flexural Capacity ◽  
Equivalent Thickness ◽  
High Rise ◽  
Safety Glass ◽  
Current Design ◽  
Good Agreement

Laminated glass has been increasing widely used in high rise buildings as a kind of safety glass in recent years. So we should analyze its material property. In this paper, we use flexural experiments and ANSYS program to analyze the main factors that affect the flexural capacity of the laminated glass. The test results show that the flexural capacity is closely related to film. And the ANSYS program had got good agreement with the experimental results. Comparison of experimental results with calculated ones indicates that the current design code will lead to conservative results and the equivalent thickness of laminated glasses provided in the code should be further discussed.

Sign in / Sign up

Export Citation Format

Share Document