Stress along tensile lap-spliced fibre reinforced polymer reinforcing bars in concrete

2007 ◽  
Vol 34 (9) ◽  
pp. 1149-1158 ◽  
Author(s):  
Ragi Aly
Keyword(s):  
Mathematical Model ◽  
Large Scale ◽  
Bond Stress ◽  
Experimental Results ◽  
Reinforcing Bars ◽  
Reinforced Polymer ◽  
Pullout Tests ◽  
Fibre Reinforced Polymer ◽  
Displacement Theory ◽  
Frp Bars

A theoretical study was carried out to investigate stress along tensile lap-spliced spaced or bundled fibre reinforced polymer (FRP) bars in concrete. R. Tepfers developed a mathematical model, which could be applied for any type of reinforcing bar, based on the modulus of displacement theory. The mathematical model can predict the bond stress and stresses in the reinforcing bars and the surrounding concrete. In this paper, the model developed by Tepfers was represented by applying the modulus of displacement theory, and theoretical predictions are compared with the experimental results from testing 16 large-scale concrete beams. Good agreement between the theoretical values and experimental results was observed at three stages of loading. Recommendations for investigating the modulus of displacement from pullout tests have been included. Lastly, the maximum average bond stress of spliced FRP bars can be estimated using the ultimate failure pattern analysis, in which the contributions of the splitting resistance were included.Key words: beams, fibre reinforced polymer (FRP) bars, bundled bars, concrete, tensile lap-splice, pullout tests, modulus of displacement, flexural tests.

Investigation of bond between fibre-reinforced polymer bars and concrete under sustained loads

2006 ◽  
Vol 33 (11) ◽  
pp. 1426-1437 ◽  
Author(s):  
F Shahidi ◽  
L D Wegner ◽  
B F Sparling
Keyword(s):  
Reinforced Concrete ◽  
Sustained Load ◽  
Reinforcing Bars ◽  
Bond Slip ◽  
Reinforced Polymer ◽  
Sustained Loads ◽  
Fibre Reinforced Polymer ◽  
Term Performance ◽  
Frp Bars

Although the use of fibre-reinforced polymer (FRP) bars to replace steel in reinforced concrete is becoming more common, uncertainty remains concerning the long-term performance of FRP, including the effect of a sustained load on the bond between the FRP bars and the concrete. An experimental study was therefore undertaken to investigate the long-term durability of the bond for various types of bars embedded in concrete: one type of glass FRP, two types of carbon FRP, and conventional steel reinforcing bars. Pullout specimens were tested both statically to failure and under sustained loads for periods of up to 1 year while free-end slip was monitored. Results revealed lower short-term bond strengths for FRP bars relative to steel and significant variability in long-term bond-slip performance among FRP bars of different types. Post-testing investigations revealed damage to bar surfaces at the macroscopic level, as well as broken longitudinal fibres and damage to the surface coatings at the microscopic level.Key words: reinforced concrete, fibre-reinforced polymer (FRP), bond, creep, pullout, sustained loads.

Experimental Study on Bond Behavior of GFRP-to-Cement Mortar

2011 ◽  
Vol 94-96 ◽  
pp. 543-546
Author(s):  
Ning Zhang ◽  
Ai Zhong Lu ◽  
Yun Qian Xu ◽  
Pan Cui
Keyword(s):  
Aluminium Alloy ◽  
Cement Mortar ◽  
Bond Stress ◽  
Reinforcing Bars ◽  
Bond Performance ◽  
Gfrp Bars ◽  
Pull Out ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Average Bond

Direct pull-out tests were performed to evaluate the bond performance of glass fiber-reinforced polymer (GFRP) reinforcing bars in cement mortar. Specimens with different bar diameters and different grouted lengths (i.e., 5d, 10d and 15d, d is the diameter of bars) are prepared for the pull-out tests. For comparison, specimens with plain aluminium alloy bars (AAB) were tested as well. The result shows that the average bond stress between plain aluminium alloy bars and cement is much smaller than that between the deformed GFRP bars and cement; thin GFRP bars tended to have larger average bond stress; the shorter the grouted length, the smaller the maximum average bond stress. Only part of grouted length undertakes the bond stress and the length depends on the shear modulus of GFRP and the surrounding material.

Minimum thickness of concrete members reinforced with fibre reinforced polymer bars

2001 ◽  
Vol 28 (4) ◽  
pp. 583-592 ◽  
Author(s):  
Amin Ghali ◽  
Tara Hall ◽  
William Bobey
Keyword(s):  
Reinforced Concrete ◽  
Minimum Thickness ◽  
Reinforced Polymers ◽  
Flexural Members ◽  
Steel Reinforced Concrete ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Steel Bars ◽  
Fibre Reinforced Polymer ◽  
Frp Bars

To avoid excessive deflection most design codes specify the ratio (l/h)s, the span to minimum thickness of concrete members without prestressing. Use of the values of (l/h)s specified by the codes, in selecting the thickness of members, usually yields satisfactory results when the members are reinforced with steel bars. Fibre reinforced polymer (FRP) bars have an elastic modulus lower than that of steel. As a result, the values of (l/h)s specified in codes for steel-reinforced concrete would lead to excessive deflection if adopted for FRP-reinforced concrete. In this paper, an equation is developed giving the ratio (l/h)f for use with FRP bars in terms of (l/h)s and (εs/εf), where εs and εf are the maximum strain allowed at service in steel and FRP bars, respectively. To control the width of cracks, ACI 318-99 specifies εs = 1200 × 10–6 for steel bars having a modulus of elasticity, Es, of 200 GPa and a yield strength, fy, of 400 MPa. At present, there is no value specified for εf; a value is recommended in this paper.Key words: concrete, cracking, deflection, fibre reinforced polymers, flexural members, minimum thickness.

scholarly journals Comparison of Analytical Approaches Predicting the Compressive Strength of Fibre Reinforced Polymers

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2517 ◽  
Author(s):  
Christian Leopold ◽  
Sergej Harder ◽  
Timo Philipkowski ◽  
Wilfried Liebig ◽  
Bodo Fiedler
Keyword(s):  
Compressive Strength ◽  
Prediction Accuracy ◽  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Experimental Results ◽  
Analytical Models ◽  
Reinforced Polymers ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Analytical Approaches

Common analytical models to predict the unidirectional compressive strength of fibre reinforced polymers are analysed in terms of their accuracy. Several tests were performed to determine parameters for the models and the compressive strength of carbon fibre reinforced polymer (CFRP) and glass fibre reinforced polymer (GFRP). The analytical models are validated for composites with glass and carbon fibres by using the same epoxy matrix system in order to examine whether different fibre types are taken into account. The variation in fibre diameter is smaller for CFRP. The experimental results show that CFRP has about 50% higher compressive strength than GFRP. The models exhibit significantly different results. In general, the analytical models are more precise for CFRP. Only one fibre kinking model’s prediction is in good agreement with the experimental results. This is in contrast to previous findings, where a combined modes model achieves the best prediction accuracy. However, in the original form, the combined modes model is not able to predict the compressive strength for GFRP and was adapted to address this issue. The fibre volume fraction is found to determine the dominating failure mechanisms under compression and thus has a high influence on the prediction accuracy of the various models.

scholarly journals FLEXURAL CAPACITY OF CONCRETE BEAMS REINFORCED WITH STEEL AND FIBRE‐REINFORCED POLYMER (FRP) BARS

2004 ◽  
Vol 10 (3) ◽  
pp. 209-215
Author(s):  
Hau Yan Leung
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Beam Design ◽  
Reinforced Concrete Member ◽  
Current Design ◽  
Fibre Reinforced Polymer ◽  
Steel Rebars ◽  
Frp Bars

Although much research on concrete beams reinforced with fibre‐reinforced polymer (FRP) rods has been conducted in recent years, their use still does not receive the attention it deserves from practicising engineers. This is attributed to the fact that FRP is brittle in nature and the collapse of FRP‐reinforced concrete member may be catastrophic. A rational beam design can incorporate a hybrid use of FRP rods and steel rods. Current design codes only deal with steel‐reinforced or FRP‐reinforced concrete members. Therefore in this study some design charts and equations for concrete beam sections reinforced with FRP rods and steel rebars were generated. Results from the theoretical derivations agreed well with experimental data.

NUMERICAL ANALYSIS OF CONCRETE BEAM REINFORCED WITH GLASS FIBER REINFORCED POLYMER BARS

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Osama A. Mohamed ◽  
Rania Khattab
Keyword(s):  
Finite Element ◽  
Numerical Analysis ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Reinforcing Bars ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Steel Bars ◽  
Frp Bars

The use of fiber reinforced polymer (FRP) bars to reinforce concrete beams has received significant attention in the past decade due to their corrosion resistance, high tensile strength, and excellent non-magnetic properties. Glass FRP (GFRP) reinforcing bars have gained popularity due to the relatively lower cost compared to carbon FRP (CFRP) bars. In this study, sixteen concrete beam finite element models were created using the finite element computer program ANSYS to perform linear and non-linear analyses. Twelve beams were longitudinally reinforced with GFRP bars, while the remaining four beams were reinforced with conventional steel bars as control specimens. In terms of mechanical properties, FRP reinforcing bars have lower modulus of elasticity compared to conventional reinforcing steel and remain linear elastic up to failure. This leads to lack of plasticity and a brittle failure of beams reinforced with FRP bars. The objective of this study is to investigate flexural behavior of concrete beams reinforced with GFRP reinforcing bars. Some of the parameters incorporated in the numerical analysis include longitudinal reinforcement ratio and compressive strength of concrete, both of which affect the flexural capacity of beams. It is shown in this study that replacement of traditional reinforcing steel reinforced bars by GFRP bars significantly decreases mid-span deflection and increases ultimate load. The strain distribution along GFRP longitudinal reinforcing bars is totally different from that of traditional steel bars.

Fibre-reinforced polymer composite bars for the concrete deck slab of Wotton Bridge

2003 ◽  
Vol 30 (5) ◽  
pp. 861-870 ◽  
Author(s):  
Ehab El-Salakawy ◽  
Brahim Benmokrane ◽  
Gérard Desgagné
Keyword(s):  
Field Test ◽  
Remote Monitoring ◽  
Concrete Bridges ◽  
Fibre Optic ◽  
Reinforced Polymer ◽  
Deck Slabs ◽  
Fibre Reinforced Polymer ◽  
Concrete Deck ◽  
Frp Bars ◽  
Deck Slab

A new concrete bridge in the Municipality of Wotton, Quebec, Canada, was constructed using fibre-reinforced polymer (FRP) bars as reinforcement for the deck slab. The new bridge is a girder type with four main girders simply supported over a span of 30.60 m. One half of the concrete deck slab was reinforced with carbon and glass FRP bars, and the other half with conventional steel bars. The design of the reinforced concrete deck slab was made according to sections 8 and 16 of the new Canadian Highway Bridge Design Code. The bridge was well instrumented at critical locations for long-term internal temperature and strain data collection using fibre optic sensors. The construction of the bridge was completed and the bridge opened for traffic in October 2001. The bridge was then tested for service performance using standard truckloads. Design, construction details, and the results of the field test and 1 year of remote monitoring are discussed. Under the same real service and environmental conditions, very similar behaviour was obtained from the FRP (glass and carbon) and steel bars.Key words: concrete bridges, deck slabs, FRP bars, field test, fibre optic sensors, remote monitoring, serviceability.

Concrete flexural members reinforced with fiber reinforced polymer: design for cracking and deformability

2002 ◽  
Vol 29 (1) ◽  
pp. 125-134 ◽  
Author(s):  
John Newhook ◽  
Amin Ghali ◽  
Gamil Tadros
Keyword(s):  
Cross Sectional Area ◽  
Fiber Reinforced Polymer ◽  
Sectional Area ◽  
Fiber Reinforced ◽  
Cross Sectional ◽  
Flexural Members ◽  
Crack Control ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Frp Bars

Fiber reinforced polymer (FRP) bars have lower modulus of elasticity than steel bars. For this reason when FRP bars are used as flexural nonprestressed reinforcement in concrete sections, the stress in the FRP is limited to a relatively small fraction of its tensile strength. This limit, necessary to control width of cracks at service, governs design of the required cross-sectional area of the FRP. Parametric studies on rectangular and T-sections are presented to show that the design based on allowable strain in the FRP results in sections that exhibit large deformation before failure. The concept of deformability, given in the Canadian Highway Bridge Design Code, as a requirement in the design of sections is discussed and modifications suggested. Using the new definition, it is shown that when, in addition to the crack control requirement, an upper limit is imposed on the cross-sectional area of the FRP, no calculations will be necessary to check the deformability.Key words: fibre reinforced polymer, reinforcement, concrete, design, deformability.

Sign in / Sign up

Export Citation Format

Share Document