scholarly journals A dual-phase alloy with ultrahigh strength-ductility synergy over a wide temperature range

2021 ◽  
Vol 7 (34) ◽  
pp. eabi4404
Author(s):  
Raymond Kwesi Nutor ◽  
Qingping Cao ◽  
Ran Wei ◽  
Qingmei Su ◽  
Gaohui Du ◽  
...  
Keyword(s):  
Wide Temperature Range ◽  
Elevated Temperatures ◽  
Interesting Property ◽  
Specific Yield ◽  
Dynamic Strain ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Temperature Range ◽  
Face Centered ◽  
Multiple Deformation

High-entropy alloys (HEAs), as an emerging class of materials, have pointed a pathway in developing alloys with interesting property combinations. Although they are not exempted from the strength-ductility trade-off, they present a standing chance in overcoming this challenge. Here, we report results for a precipitation-strengthening strategy, by tuning composition to design a CoNiV-based face-centered cubic/B2 duplex HEA. This alloy sustains ultrahigh gigapascal-level tensile yield strengths and excellent ductility from cryogenic to elevated temperatures. The highest specific yield strength (~150.2 MPa·cm3/g) among reported ductile HEAs is obtained. The ability of the alloy presented here to sustain this excellent strength-ductility synergy over a wide temperature range is aided by multiple deformation mechanisms i.e., twins, stacking faults, dynamic strain aging, and dynamic recrystallization. Our results open the avenue for designing precipitation-strengthened lightweight HEAs with advanced strength-ductility combinations over a wide service temperature range.

scholarly journals Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Tianhao Wang ◽  
Shivakant Shukla ◽  
Bharat Gwalani ◽  
Subhasis Sinha ◽  
Saket Thapliyal ◽  
...  
Keyword(s):  
Current Approach ◽  
Deformation Mechanisms ◽  
Engineering Properties ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Friction Stir ◽  
The Matrix ◽  
Face Centered ◽  
Multiple Deformation

AbstractTuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

scholarly journals Cooperative deformation in high-entropy alloys at ultralow temperatures

2020 ◽  
Vol 6 (13) ◽  
pp. eaax4002 ◽  
Author(s):  
Muhammad Naeem ◽  
Haiyan He ◽  
Fan Zhang ◽  
Hailong Huang ◽  
Stefanus Harjo ◽  
...  
Keyword(s):  
Deformation Mechanisms ◽  
Dislocation Slip ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
In Situ Experiments ◽  
Ultralow Temperatures ◽  
Face Centered ◽  
Multiple Deformation

High-entropy alloys exhibit exceptional mechanical properties at cryogenic temperatures, due to the activation of twinning in addition to dislocation slip. The coexistence of multiple deformation pathways raises an important question regarding how individual deformation mechanisms compete or synergize during plastic deformation. Using in situ neutron diffraction, we demonstrate the interaction of a rich variety of deformation mechanisms in high-entropy alloys at 15 K, which began with dislocation slip, followed by stacking faults and twinning, before transitioning to inhomogeneous deformation by serrations. Quantitative analysis showed that the cooperation of these different deformation mechanisms led to extreme work hardening. The low stacking fault energy plus the stable face-centered cubic structure at ultralow temperatures, enabled by the high-entropy alloying, played a pivotal role bridging dislocation slip and serration. Insights from the in situ experiments point to the role of entropy in the design of structural materials with superior properties.

Voids in Irradiated Tungsten and Molybdenum

1969 ◽  
Vol 27 ◽  
pp. 190-191
Author(s):  
Robert C. Rau ◽  
Robert L. Ladd
Keyword(s):  
Melting Point ◽  
Fast Neutron ◽  
Neutron Irradiation ◽  
Elevated Temperatures ◽  
Irradiation Temperature ◽  
The Body ◽  
Face Centered Cubic ◽  
Body Centered Cubic ◽  
Cubic Metals ◽  
Face Centered

Recent studies have shown the presence of voids in several face-centered cubic metals after neutron irradiation at elevated temperatures. These voids were found when the irradiation temperature was above 0.3 Tm where Tm is the absolute melting point, and were ascribed to the agglomeration of lattice vacancies resulting from fast neutron generated displacement cascades. The present paper reports the existence of similar voids in the body-centered cubic metals tungsten and molybdenum.

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

scholarly journals Effects of Different Contents of Each Component on the Structural Stability and Mechanical Properties of Co-Cr-Fe-Ni High-Entropy Alloys

2021 ◽  
Vol 11 (6) ◽  
pp. 2832
Author(s):  
Haibo Liu ◽  
Cunlin Xin ◽  
Lei Liu ◽  
Chunqiang Zhuang
Keyword(s):  
Mechanical Properties ◽  
Structural Stability ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
Obvious Effect ◽  
High Entropy ◽  
Precise Control ◽  
Component Content ◽  
Face Centered ◽  
And Performance

The structural stability of high-entropy alloys (HEAs) is closely related to their mechanical properties. The precise control of the component content is a key step toward understanding their structural stability and further determining their mechanical properties. In this study, first-principle calculations were performed to investigate the effects of different contents of each component on the structural stability and mechanical properties of Co-Cr-Fe-Ni HEAs based on the supercell model. Co-Cr-Fe-Ni HEAs were constructed based on a single face-centered cubic (FCC) solid solution. Elemental components have a clear effect on their structure and performance; the Cr and Fe elements have an obvious effect on the structural stability and equilibrium lattice constant, respectively. The Ni elements have an obvious effect on stiffness. The Pugh ratios indicate that Cr and Ni addition may increase ductility, whereas Co and Fe addition may decrease it. With increasing Co and Fe contents or decreasing Cr and Ni contents, the structural stability and stiffness of Co-Cr-Fe-Ni HEAs are improved. The structural stability and mechanical properties may be related to the strength of the metallic bonding and covalent bonding inside Co-Cr-Fe-Ni HEAs, which, in turn, is determined by the change in element content. Our results provide the underlying insights needed to guide the optimization of Co-Cr-Fe-Ni HEAs with excellent mechanical properties.

scholarly journals Microstructure Refinement by Low-Temperature Ausforming in an Fe-Based Metastable High-Entropy Alloy

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 742
Author(s):  
Motomichi Koyama ◽  
Takeaki Gondo ◽  
Kaneaki Tsuzaki
Keyword(s):  
Low Temperature ◽  
Plastic Anisotropy ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Microstructure Refinement ◽  
Hexagonal Close Packed ◽  
Solution Treated Condition ◽  
Solution Treated ◽  
Face Centered

The effects of ausforming in an Fe30Mn10Cr10Co high-entropy alloy on the microstructure, hardness, and plastic anisotropy were investigated. The alloy showed a dual-phase microstructure consisting of face-centered cubic (FCC) austenite and hexagonal close-packed (HCP) martensite in the as-solution-treated condition, and the finish temperature for the reverse transformation was below 200 °C. Therefore, low-temperature ausforming at 200 °C was achieved, which resulted in microstructure refinement and significantly increased the hardness. Furthermore, plasticity anisotropy, a common problem in HCP structures, was suppressed by the ausforming treatment. This, in turn, reduced the scatter of the hardness.

scholarly journals In-Situ TEM Annealing Observation of Helium Bubble Evolution in Pre-Irradiated FeCoNiCrTi0.2 Alloys

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3727
Author(s):  
Huanhuan He ◽  
Zhiwei Lin ◽  
Shengming Jiang ◽  
Xiaotian Hu ◽  
Jian Zhang ◽  
...  
Keyword(s):  
Vacuum Arc ◽  
In Situ Tem ◽  
Face Centered Cubic ◽  
Helium Bubble ◽  
High Entropy ◽  
Helium Bubbles ◽  
Transmission Electron ◽  
Bubble Evolution ◽  
Face Centered

The FeCoNiCrTi0.2 high-entropy alloys fabricated by vacuum arc melting method, and the annealed pristine material, are face centered cubic structures with coherent γ’ precipitation. Samples were irradiated with 50 keV He+ ions to a fluence of 2 × 1016 ions/cm2 at 723 K, and an in situ annealing experiment was carried out to monitor the evolution of helium bubbles during heating to 823 and 923 K. The pristine structure of FeCoNiCrTi0.2 samples and the evolution of helium bubbles during in situ annealing were both characterized by transmission electron microscopy. The annealing temperature and annealing time affect the process of helium bubbles evolution and formation. Meanwhile, the grain boundaries act as sinks to accumulate helium bubbles. However, the precipitation phase seems have few effects on the helium bubble evolution, which may be due to the coherent interface and same structure of γ’ precipitation and matrix.

Insights into Defect-Mediated Nucleation of Equilibrium B2 Phase in Face-Centered Cubic High-Entropy Alloys

JOM ◽  
2021 ◽  
Author(s):  
Abhishek Sharma ◽  
Bharat Gwalani ◽  
Sriswaroop Dasari ◽  
Deep Choudhuri ◽  
Yao-Jen Chang ◽  
...  
Keyword(s):  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
B2 Phase ◽  
Face Centered

scholarly journals Effect of Grain Size on Carburization Characteristics of the High-Entropy Equiatomic CoCrFeMnNi Alloy

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7199
Author(s):  
Hyunbin Nam ◽  
Jeongwon Kim ◽  
Namkyu Kim ◽  
Sangwoo Song ◽  
Youngsang Na ◽  
...  
Keyword(s):  
Grain Size ◽  
Grain Boundaries ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Grain Sizes ◽  
Fine Grain ◽  
Cast Specimen ◽  
Vacuum Carburization ◽  
Cold Rolled ◽  
Face Centered

In this study, the carburization characteristics of cast and cold-rolled CoCrFeMnNi high-entropy alloys (HEAs) with various grain sizes were investigated. All specimens were prepared by vacuum carburization at 940 °C for 8 h. The carburized/diffused layer was mainly composed of face-centered cubic structures and Cr7C3 carbide precipitates. The carburized/diffused layer of the cold-rolled specimen with a fine grain size (~1 μm) was thicker (~400 μm) than that of the carburized cast specimen (~200 μm) with a coarse grain size (~1.1 mm). In all specimens, the carbides were formed primarily through grain boundaries, and their distribution varied with the grain sizes of the specimens. However, the carbide precipitates of the cast specimen were formed primarily at the grain boundaries and were unequally distributed in the specific grains. Owing to the non-uniform formation of carbides in the carburized cast specimen, the areas in the diffused layer exhibited various carbide densities and hardness distributions. Therefore, to improve the carburization efficiency of equiatomic CoCrFeMnNi HEAs, it is necessary to refine the grain sizes.

Sign in / Sign up

Export Citation Format

Share Document