scholarly journals Rebound of self-lubricating compound drops

2020 ◽  
Vol 6 (11) ◽  
pp. eaay3499 ◽  
Author(s):  
Nathan Blanken ◽  
Muhammad Saeed Saleem ◽  
Carlo Antonini ◽  
Marie-Jean Thoraval
Keyword(s):  
Solid Surface ◽  
High Speed ◽  
Water Drop ◽  
Three Dimensional ◽  
Strong Impact ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Compound Drops ◽  
The Impact ◽  
Dimensional Printing

Drop impact on solid surfaces is encountered in numerous natural and technological processes. Although the impact of single-phase drops has been widely explored, the impact of compound drops has received little attention. Here, we demonstrate a self-lubrication mechanism for water-in-oil compound drops impacting on a solid surface. Unexpectedly, the core water drop rebounds from the surface below a threshold impact velocity, irrespective of the substrate wettability. This is interpreted as the result of lubrication from the oil shell that prevents contact between the water core and the solid surface. We combine side and bottom view high-speed imaging to demonstrate the correlation between the water core rebound and the oil layer stability. A theoretical model is developed to explain the observed effect of compound drop geometry. This work sets the ground for precise complex drop deposition, with a strong impact on two- and three-dimensional printing technologies and liquid separation.

scholarly journals Laser-induced forward transfer of viscoplastic fluids

2019 ◽  
Vol 880 ◽  
pp. 497-513 ◽  
Author(s):  
Maziyar Jalaal ◽  
Martin Klein Schaarsberg ◽  
Claas-Willem Visser ◽  
Detlef Lohse
Keyword(s):  
High Speed ◽  
Laser Energy ◽  
Three Dimensional ◽  
Liquid Jet ◽  
Control Parameters ◽  
Optimal Conditions ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Forward Transfer ◽  
Dimensional Printing

Laser-induced forward transfer (LIFT) is a nozzle-free printing technology that can be used for two- and three-dimensional printing. In LIFT, a laser pulse creates an impulse inside a thin film of material that results in the formation of a liquid jet. We experimentally study LIFT of viscoplastic materials by visualizing the process of jetting with high-speed imaging. The shape of the jet depends on the laser energy, focal height, surface tension and material rheology. We theoretically identify the characteristic jetting velocity and how it depends on the control parameters, and define non-dimensional groups to classify the regimes of jetting. Based on the results, we propose the optimal conditions for printing with LIFT technology.

scholarly journals Study of Layer Formation During Droplet-Based Three-Dimensional Printing of Gel Structures

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Kyle Christensen ◽  
Yong Huang
Keyword(s):  
Inkjet Printing ◽  
High Speed ◽  
Three Dimensional ◽  
Layer By Layer ◽  
Layer Formation ◽  
High Speed Imaging ◽  
Three Dimensional Printing ◽  
Drop On Demand ◽  
Image Velocimetry ◽  
Dimensional Printing

Additive manufacturing, also known as three-dimensional (3D) printing, is an approach in which a structure may be fabricated layer by layer. For 3D inkjet printing, droplets are ejected from a nozzle, and each layer is formed droplet by droplet. Inkjet printing has been widely applied for the fabrication of 3D biological gel structures, but the knowledge of the microscale interactions between printed droplets is still largely elusive. This study aims to elucidate the layer formation mechanism in terms of the formation of single lines and layers comprised of adjacent lines during drop-on-demand inkjet printing of alginate using high speed imaging and particle image velocimetry. Inkjet droplets are found to impact, spread, and coalesce within a fluid region at the deposition site, forming coherent printed lines within a layer. The effects of printing conditions on the behavior of droplets during layer formation are discussed and modeled based on gelation dynamics, and recommendations are presented to enable controllable and reliable fabrication of gel structures. The effects of gelation on droplet impact dynamics are found to be negligible during alginate printing, and interfaces are found to form between printed lines within a layer depending on printing conditions, printing path orientation, and gelation dynamics.

scholarly journals Air mediates the impact of a compliant hemisphere on a rigid smooth surface

Soft Matter ◽  
2021 ◽  
Author(s):  
Siqi Zheng ◽  
Sam Dillavou ◽  
John M. Kolinski
Keyword(s):  
Elastic Body ◽  
Elastic Properties ◽  
Impact Velocity ◽  
Solid Surface ◽  
High Speed ◽  
Smooth Surface ◽  
High Speed Imaging ◽  
The Impact ◽  
Rigid Smooth

When a soft elastic body impacts upon a smooth solid surface, the intervening air fails to drain, deforming the impactor. High-speed imaging with the VFT reveal rich dynamics and sensitivity to the impactor's elastic properties and the impact velocity.

scholarly journals Transfiguring Healthcare: Three-Dimensional Printing in Pharmaceutical Sciences; Trends during COVID-19: A Review

2021 ◽  
pp. 207-218
Author(s):  
K. G. Siree ◽  
T. M. Amulya ◽  
T. M. Pramod Kumar ◽  
S. Sowmya ◽  
K. Divith ◽  
...  
Keyword(s):  
3D Printing ◽  
Medical Devices ◽  
Three Dimensional ◽  
Pharmaceutical Sciences ◽  
Three Dimensional Printing ◽  
Custom Made ◽  
High Degree ◽  
The Impact ◽  
Dimensional Printing ◽  
Shed Light

Three-dimensional (3D) printing is a unique technique that allows for a high degree of customisation in pharmacy, dentistry and in designing of medical devices. 3D printing satiates the increasing exigency for consumer personalisation in these fields as custom-made medicines catering to the patients’ requirements are novel advancements in drug therapy. Current research in 3D printing indicates towards reproducing an organ in the form of a chip; paving the way for more studies and opportunities to perfecting the existing technique. In addition, we will also attempt to shed light on the impact of 3D printing in the COVID-19 pandemic.

scholarly journals Effect of Three-dimensional Printing with Nanotubes on Impact Resistance

2019 ◽  
Author(s):  
Anne Schmitz
Keyword(s):  
Mechanical Properties ◽  
Lower Limb ◽  
Impact Resistance ◽  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Impact Tester ◽  
The Impact ◽  
Dimensional Printing ◽  
Pendulum Impact ◽  
Pendulum Impact Tester

Abstract The types of biomedical devices that can be three-dimensional printed (3DP) is limited by the mechanical properties of the resulting materials. As a result, much research has focused on adding carbon nanotubes (CNT) to these photocurable polymers to make them stronger. However, there is little to no data on how CNTs affect the impact resistance of these polymers, an important property when designing and manufacturing lower limb prosthetics. The objective of this study was to expand the use of 3DP to prosthetics by testing the hypothesis that adding CNTs to a stereolithographic (SLA) photocurable resin will result in a cured polymer with increased impact resistance. Twenty-six total specimens: 13 with nanotubes and 13 without nanotubes, were printed on a Form2 SLA printer. Once all the specimens were printed, washed, and cured, the impact resistance was quantified using a pendulum impact tester in a notched Izod configuration. Contrary to the hypothesis, the specimens with SWCNTs (0.312 ± 0.036 ft*lb/in) had a significantly lower impact resistance compared to the non-SWCNT specimens (0.364 ± 0.055 ft*lb/in), U = 34.0, p = 0.004. This decreased impact resistance may be due to voids in the printed polymer around the aggregated nanotubes. Thus, SLA polymers still do not have the impact strength needed to be used for a full lower limb prosthetic.

scholarly journals Bubble Dynamics in a Narrow Gap Flow under the Influence of Pressure Gradient and Shear Flow

Fluids ◽  
2020 ◽  
Vol 5 (4) ◽  
pp. 208
Author(s):  
Peter Reinke ◽  
Jan Ahlrichs ◽  
Tom Beckmann ◽  
Marcus Schmidt
Keyword(s):  
Shear Flow ◽  
Pressure Gradient ◽  
High Speed ◽  
Bubble Dynamics ◽  
Three Dimensional ◽  
High Speed Imaging ◽  
Two Phase ◽  
Bubble Generation ◽  
Gap Flow ◽  
The Impact

The volume-of-flow method combined with the Rayleigh–Plesset equation is well established for the computation of cavitation, i.e., the generation and transportation of vapor bubbles inside a liquid flow resulting in cloud, sheet or streamline cavitation. There are, however, limitations, if this method is applied to a restricted flow between two adjacent walls and the bubbles’ size is of the same magnitude as that of the clearance between the walls. This work presents experimental and numerical results of the bubble generation and its transportation in a Couette-type flow under the influence of shear and a strong pressure gradient which are typical for journal bearings or hydraulic seals. Under the impact of variations of the film thickness, the VoF method produces reliable results if bubble diameters are less than half the clearance between the walls. For larger bubbles, the wall contact becomes significant and the bubbles adopt an elliptical shape forced by the shear flow and under the influence of a strong pressure gradient. Moreover, transient changes in the pressure result in transient cavitation, which is captured by high-speed imaging providing material to evaluate transient, three-dimensional computations of a two-phase flow.

i4.0, 3D printing, deglobalisation and new manufacturing clusters: The view from Australia

2020 ◽  
pp. 103530462098142
Author(s):  
Al Rainnie
Keyword(s):  
Manufacturing Industry ◽  
New Technologies ◽  
Manufacturing Sector ◽  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Jel Code ◽  
The One ◽  
The Impact ◽  
Dimensional Printing ◽  
Work And Employment

Before the COVID-19 pandemic erupted onto the world stage, a new narrative was apparently beginning to emerge about the impact of i4.0 and new technologies in general, and three-dimensional printing in particular, on the future of work and employment. This was to have particular geographical implications for the manufacturing sector in particular. Proponents of i4.0 also suggested that this process, particularly in manufacturing, would promote the re-emergence of patterns of clustering. Developments in advanced manufacturing, particularly three-dimensional printing, would accelerate and reinforce these tendencies. This article looks at the role that three-dimensional printing is supposed to play in the new world, and in particular, critically evaluates its role in reinforcing the trend towards deglobalisation on the one hand, and, on the other, new clusters of manufacturing industry. JEL code: O33

scholarly journals Probing the nanoscale: the first contact of an impacting drop

2015 ◽  
Vol 785 ◽  
Author(s):  
E. Q. Li ◽  
I. U. Vakarelski ◽  
S. T. Thoroddsen
Keyword(s):  
Solid Surface ◽  
High Speed ◽  
Water Drop ◽  
Triple Line ◽  
Immiscible Liquid ◽  
Initial Contact ◽  
High Speed Imaging ◽  
Left Behind ◽  
Drop Impacts ◽  
First Contact

When a drop impacts onto a solid surface, the lubrication pressure in the air deforms its bottom into a dimple. This makes the initial contact with the substrate occur not at a point but along a ring, thereby entrapping a central disc of air. We use ultra-high-speed imaging, with 200 ns time resolution, to observe the structure of this first contact between the liquid and a smooth solid surface. For a water drop impacting onto regular glass we observe a ring of microbubbles, due to multiple initial contacts just before the formation of the fully wetted outer section. These contacts are spaced by a few microns and quickly grow in size until they meet, thereby leaving behind a ring of microbubbles marking the original air-disc diameter. On the other hand, no microbubbles are left behind when the drop impacts onto molecularly smooth mica sheets. We thereby conclude that the localized contacts are due to nanometric roughness of the glass surface, and the presence of the microbubbles can therefore distinguish between glass with 10 nm roughness and perfectly smooth glass. We contrast this entrapment topology with the initial contact of a drop impacting onto a film of extremely viscous immiscible liquid, where the initial contact appears to be continuous along the ring. Here, an azimuthal instability occurs during the rapid contraction at the triple line, also leaving behind microbubbles. For low impact velocities the nature of the initial contact changes to one initiated by ruptures of a thin lubricating air film.

Effect of Three-Dimensional Printing With Nanotubes on Impact and Fatigue Resistance

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Anne Schmitz
Keyword(s):  
Fatigue Resistance ◽  
Impact Resistance ◽  
Three Dimensional ◽  
Impact Testing ◽  
Three Dimensional Printing ◽  
Impact Tester ◽  
The Impact ◽  
Dimensional Printing ◽  
Pendulum Impact ◽  
Pendulum Impact Tester

Abstract The types of biomedical devices that can be three-dimensional printed (3DP) are limited by the mechanical properties of the resulting materials. As a result, much research has been focused on adding carbon nanotubes (CNT) to these photocurable polymers to make them stronger. The objective of this study was to expand the use of 3DP to prosthetics by testing the hypothesis that adding CNTs to a stereolithographic (SLA) photocurable resin will result in a cured polymer with increased impact and fatigue resistance. For impact testing, twenty-six total specimens, 13 with nanotubes and 13 without nanotubes, were printed on a Form2 SLA printer. Once all the specimens were printed, washed, and cured, the impact resistance was quantified using a pendulum impact tester using a notched Izod configuration. Similarly, twelve R. R. Moore fatigue specimens were printed, washed, and cured. The specimens with SWCNTs (0.312 ± 0.036 ft lb/in.) had a significantly lower impact resistance compared to the non-SWCNT specimens (0.364 ± 0.055 ft lb/in.), U = 34.0, p = 0.004. Adding SWCNTs also reduced the short cycle fatigue life (i.e., 103) from 3.1 × 5 to 8.8 × 3 psi and increased the endurance limit from 0.4 to 3.0 × 3 psi. If used for creating a foot prosthetic, the non-SWCNT polymer would last 2919 cycles while the SWCNT mixture would last <1 cycle. Therefore, SLA polymers do not yet have the impact and fatigue resistance capabilities to be used for prosthetic feet.

scholarly journals Exploring the Optimal Design for and Experimentation on a Bowl-Based Mechanism for Transplanting Potted Strawberry Seedlings

2021 ◽  
Author(s):  
Yin Daqing ◽  
Yang Yuchao ◽  
Zhou Maile ◽  
Wei Mingxu ◽  
Wang Jinwu
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
High Speed Photography ◽  
Simulation Design ◽  
Three Dimensional Model ◽  
Three Dimensional Printing ◽  
New Device ◽  
Working Principle ◽  
Dimensional Printing ◽  
Actual Trajectory

Abstract To improve the mechanization of strawberry planting integration and the efficiency of fetching and transplanting seedlings, an integrated transplanting mechanism with protruding, fetching and planting is designed. This new device can realize rapid fetching and pushing bowl movements. The working principle of the slewing mechanism is analyzed, a kinematics model of the mechanism is established, and the optimization goal is established. Visual auxiliary analysis software is developed, optimized parameters are established, and the corresponding theoretical trajectory is provided. A three-dimensional model is established and a virtual simulation design analysis is performed to obtain a simulation trajectory. Three-dimensional printing technology is used to manufacture the test prototype, and the actual working trajectory of the test prototype is extracted using high-speed photography technology, which verifies the consistency of the actual trajectory with the theoretical and simulated trajectories. A prototype transplanting experiment is performed, showing that the success rate of seedling extraction is 91.2% and the rate of excellent planting is 82.8%, which meet the requirements for integrated strawberry harvesting, planting and transplanting and verify the correctness and feasibility of the mechanism design.

Sign in / Sign up

Export Citation Format

Share Document