scholarly journals Characterization of bidirectional impulse turbines for thermoacoustic engines

2019 ◽  
Vol 146 (5) ◽  
pp. 3524-3535 ◽  
Author(s):  
Michael A. G. Timmer ◽  
Theo H. van der Meer
Keyword(s):  
Thermoacoustic Engines

Characterization of Piezoelectric Materials for Thermoacoustic Power Transduction

2008 ◽  
Author(s):  
A. Wekin ◽  
C. Richards ◽  
K. Matveev ◽  
M. Anderson
Keyword(s):  
Experimental Study ◽  
Piezoelectric Materials ◽  
Electrical Power ◽  
Power Production ◽  
Piezoelectric Transducers ◽  
Maximum Power ◽  
Small Scale ◽  
Thermoacoustic Engine ◽  
Thermoacoustic Engines

In this work an experimental study of the performance of piezoelectric transducers for power production from a small-scale thermoacoustic engine is presented. Four piezoelectric samples are identified and characterized. These samples are tested on a variable acoustic driver and electrical power produced is measured. Finally, the samples are tested on four experimental thermoacoustic engines to verify the results from the acoustic setup. The maximum power produced is 177 μW from a closed thermoacoustic engine coupled to a 15mm PZT disk.

scholarly journals Development and Characterization of a Low-Cost Sensors System for an Acoustic Test Bench

Sensors ◽  
2020 ◽  
Vol 20 (22) ◽  
pp. 6663
Author(s):  
Ciro Moreno-Ramírez ◽  
Carmen Iniesta ◽  
Alejandro González ◽  
José Luis Olazagoitia
Keyword(s):  
Test Bench ◽  
Mechanical Design ◽  
Dynamic Pressure ◽  
Low Cost ◽  
Pressure Sensors ◽  
Acquisition System ◽  
Sampling System ◽  
Thermoacoustic Engines ◽  
And Control

Existing acoustic test benches are usually costly devices based on proprietary designs, sensors, and acquisition devices. In this paper, a low-cost test bench for acoustic purposes is introduced. The design of the test bench takes into account not only the low-cost mechanical design, but also uses low-cost sensors and control boards. This test bench has been designed for a range of signals compatible with those used by thermoacoustic engines, but it can be useful for applications with similar requirements. Taking advantage of an auxiliary pressure reference, low-cost unidirectional differential pressure sensors can be used to significantly increase the accuracy of the sampling system. The acoustic and mechanical design and development are presented along with the sampling system and the sensors arrangement implemented. Both the sensor and sampling system are evaluated by comparison with a high-fidelity sound acquisition system. An unexpected effect on the time error values distribution of the low-cost acquisition system is found and described. Finally, the errors introduced by the system and the sensors in terms of time and pressure sampling are characterized. As a result, the low-cost system’s accuracy has been satisfactory assessed and validated for the conditions expected in thermoacoustic experiments in terms of frequency and dynamic pressure.

Morphological Characterization of Mycobacteriophage R1

1974 ◽  
Vol 32 ◽  
pp. 254-255
Author(s):  
B. L. Soloff ◽  
T. A. Rado
Keyword(s):  
Carbon Source ◽  
Stationary Phase ◽  
Growth Phase ◽  
Minimal Medium ◽  
Morphological Characterization ◽  
Logarithmic Growth Phase ◽  
Complete Lysis ◽  
Lysogenic Culture ◽  
Logarithmic Growth

Mycobacteriophage R1 was originally isolated from a lysogenic culture of M. butyricum. The virus was propagated on a leucine-requiring derivative of M. smegmatis, 607 leu−, isolated by nitrosoguanidine mutagenesis of typestrain ATCC 607. Growth was accomplished in a minimal medium containing glycerol and glucose as carbon source and enriched by the addition of 80 μg/ ml L-leucine. Bacteria in early logarithmic growth phase were infected with virus at a multiplicity of 5, and incubated with aeration for 8 hours. The partially lysed suspension was diluted 1:10 in growth medium and incubated for a further 8 hours. This permitted stationary phase cells to re-enter logarithmic growth and resulted in complete lysis of the culture.

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Characterization of Coherent, Ordered Precipitates in Nickel-Base Alloys

1973 ◽  
Vol 31 ◽  
pp. 144-145
Author(s):  
B. H. Kear ◽  
J. M. Oblak
Keyword(s):  
Stable Phase ◽  
Nickel Base Superalloy ◽  
Alloy 718 ◽  
Commercial Alloy ◽  
Precipitate Morphology ◽  
Continuous Precipitation ◽  
Nickel Base ◽  
Base Superalloy ◽  
Strengthening Precipitate

A nickel-base superalloy is essentially a Ni/Cr solid solution hardened by additions of Al (Ti, Nb, etc.) to precipitate a coherent, ordered phase. In most commercial alloy systems, e.g. B-1900, IN-100 and Mar-M200, the stable precipitate is Ni3 (Al,Ti) γ′, with an LI2structure. In A lloy 901 the normal precipitate is metastable Nis Ti3 γ′ ; the stable phase is a hexagonal Do2 4 structure. In Alloy 718 the strengthening precipitate is metastable γ″, which has a body-centered tetragonal D022 structure.Precipitate MorphologyIn most systems the ordered γ′ phase forms by a continuous precipitation re-action, which gives rise to a uniform intragranular dispersion of precipitate particles. For zero γ/γ′ misfit, the γ′ precipitates assume a spheroidal.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Skeletal elements of crinoid echinoderms: High-resolution structural and microanalytical results

1983 ◽  
Vol 41 ◽  
pp. 194-195
Author(s):  
D. F. Blake ◽  
L. F. Allard ◽  
D. R. Peacor
Keyword(s):  
High Resolution ◽  
Marine Invertebrates ◽  
Sea Urchins ◽  
Structural Features ◽  
Sea Stars ◽  
High Resolution Tem ◽  
Relationship Of ◽  
The Relationship ◽  
Insight Into

Echinodermata is a phylum of marine invertebrates which has been extant since Cambrian time (c.a. 500 m.y. before the present). Modern examples of echinoderms include sea urchins, sea stars, and sea lilies (crinoids). The endoskeletons of echinoderms are composed of plates or ossicles (Fig. 1) which are with few exceptions, porous, single crystals of high-magnesian calcite. Despite their single crystal nature, fracture surfaces do not exhibit the near-perfect {10.4} cleavage characteristic of inorganic calcite. This paradoxical mix of biogenic and inorganic features has prompted much recent work on echinoderm skeletal crystallography. Furthermore, fossil echinoderm hard parts comprise a volumetrically significant portion of some marine limestones sequences. The ultrastructural and microchemical characterization of modern skeletal material should lend insight into: 1). The nature of the biogenic processes involved, for example, the relationship of Mg heterogeneity to morphological and structural features in modern echinoderm material, and 2). The nature of the diagenetic changes undergone by their ancient, fossilized counterparts. In this study, high resolution TEM (HRTEM), high voltage TEM (HVTEM), and STEM microanalysis are used to characterize tha ultrastructural and microchemical composition of skeletal elements of the modern crinoid Neocrinus blakei.

Some applications of electron beam microanalysis techniques in VLSI process evaluation

1983 ◽  
Vol 41 ◽  
pp. 160-161
Author(s):  
Simon Thomas
Keyword(s):  
Integrated Circuits ◽  
Process Evaluation ◽  
Large Scale ◽  
Technology Development ◽  
Analytical Techniques ◽  
Successful Implementation ◽  
Analysis Of Failures ◽  
Characterization Of Materials ◽  
Circuits Vlsi

Trends in the technology development of very large scale integrated circuits (VLSI) have been in the direction of higher density of components with smaller dimensions. The scaling down of device dimensions has been not only laterally but also in depth. Such efforts in miniaturization bring with them new developments in materials and processing. Successful implementation of these efforts is, to a large extent, dependent on the proper understanding of the material properties, process technologies and reliability issues, through adequate analytical studies. The analytical instrumentation technology has, fortunately, kept pace with the basic requirements of devices with lateral dimensions in the micron/ submicron range and depths of the order of nonometers. Often, newer analytical techniques have emerged or the more conventional techniques have been adapted to meet the more stringent requirements. As such, a variety of analytical techniques are available today to aid an analyst in the efforts of VLSI process evaluation. Generally such analytical efforts are divided into the characterization of materials, evaluation of processing steps and the analysis of failures.

Irradiation behavior of pyrolytic silicon carbide

1983 ◽  
Vol 41 ◽  
pp. 72-73
Author(s):  
R. J. Lauf
Keyword(s):  
Silicon Carbide ◽  
Fission Products ◽  
Thermodynamics And Kinetics ◽  
Neutron Fluences ◽  
Fuel Particles ◽  
Sic Coatings ◽  
Irradiation Behavior ◽  
Kinetics Of ◽  
Htgr Fuel

Fuel particles for the High-Temperature Gas-Cooled Reactor (HTGR) contain a layer of pyrolytic silicon carbide to act as a miniature pressure vessel and primary fission product barrier. Optimization of the SiC with respect to fuel performance involves four areas of study: (a) characterization of as-deposited SiC coatings; (b) thermodynamics and kinetics of chemical reactions between SiC and fission products; (c) irradiation behavior of SiC in the absence of fission products; and (d) combined effects of irradiation and fission products. This paper reports the behavior of SiC deposited on inert microspheres and irradiated to fast neutron fluences typical of HTGR fuel at end-of-life.

Characterization of Tamm-Horsfall Urinary Glycoprotein

1973 ◽  
Vol 31 ◽  
pp. 420-421
Author(s):  
John P. Robinson ◽  
J. David Puett
Keyword(s):  
Electron Microscopy ◽  
Circular Dichroism ◽  
Secondary Structure ◽  
Quaternary Structure ◽  
Normal Adult ◽  
Morphological Properties ◽  
Adult Males ◽  
Circular Dichroïsm ◽  
Urinary Glycoprotein

Much work has been reported on the chemical, physical and morphological properties of urinary Tamm-Horsfall glycoprotein (THG). Although it was once reported that cystic fibrotic (CF) individuals had a defective THG, more recent data indicate that THG and CF-THG are similar if not identical.No studies on the conformational aspects have been reported on this glycoprotein using circular dichroism (CD). We examined the secondary structure of THG and derivatives under various conditions and have correlated these results with quaternary structure using electron microscopy.THG was prepared from normal adult males and CF-THG from a 16-year old CF female by the method of Tamm and Horsfall. CF female by the method of Tamm and Horsfall.

Sign in / Sign up

Export Citation Format

Share Document