Three‐dimensional ultrasound image registration and shear elastic modulus reconstruction

2006 ◽  
Vol 119 (5) ◽  
pp. 3320-3320 ◽  
Author(s):  
Michael S. Richards ◽  
Nachiket H. Gokhale ◽  
Paul E. Barbone ◽  
Assad A. Oberai
Keyword(s):  
Elastic Modulus ◽  
Image Registration ◽  
Three Dimensional ◽  
Ultrasound Image ◽  
Shear Elastic Modulus

scholarly journals Three-dimensional thermomechanical converting of CTMP substrates: effect of bio-based strengthening agents and new mineral filling concept

Cellulose ◽  
2021 ◽  
Vol 28 (15) ◽  
pp. 9751-9768
Author(s):  
Teija Laukala ◽  
Sami-Seppo Ovaska ◽  
Ninja Kerttula ◽  
Kaj Backfolk
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Three Dimensional ◽  
Microfibrillated Cellulose ◽  
New Mineral ◽  
Thermomechanical Pulp ◽  
Cationic Starch ◽  
Precipitated Calcium Carbonate ◽  
Filling Method ◽  
Positive Effect

AbstractThe effects of bio-based strengthening agents and mineral filling procedure on the 3D elongation of chemi-thermomechanical pulp (CTMP) handsheets with and without mineral (PCC) filling have been investigated. The 3D elongation was measured using a press-forming machine equipped with a special converting tool. The strength of the handsheets was altered using either cationic starch or microfibrillated cellulose. Precipitated calcium carbonate (PCC) was added to the furnish either as a slurry or by precipitation of nano-sized PCC onto and into the CTMP fibre. The 3D elongation of unfilled sheets was increased by the dry-strengthening agents, but no evidence on the theorised positive effect of mineral fill on 3D elongation was seen in either filling method. The performance of the strengthening agent depended on whether the PCC was as slurry or as a precipitated PCC-CTMP. The starch was more effective with PCC-CTMP than when the PCC was added directly as a slurry to the furnish, whereas the opposite was observed with microfibrillated cellulose. The 3D elongation correlated positively with the tensile strength, bursting strength, tensile stiffness, elastic modulus and bending stiffness, even when the sheet composition was varied, but neither the strengthening agent nor the method of PCC addition affected the 3D elongation beyond what was expectable based on the tensile strength of the sheets. Finally, mechanisms affecting the properties that correlated with the 3D elongation are discussed.

Limit Load Analysis of Cracked Components Using the Reference Volume Method

2006 ◽  
Vol 129 (3) ◽  
pp. 391-399 ◽  
Author(s):  
R. Adibi-Asl ◽  
R. Seshadri
Keyword(s):  
Elastic Modulus ◽  
Three Dimensional ◽  
Local Limit ◽  
Limit Load ◽  
Multiple Cracks ◽  
Element Analysis ◽  
Limit Loads ◽  
Integrity Assessment ◽  
Reference Volume ◽  
Volume Method

Cracks and flaws occur in mechanical components and structures, and can lead to catastrophic failures. Therefore, integrity assessment of components with defects is carried out. This paper describes the Elastic Modulus Adjustment Procedures (EMAP) employed herein to determine the limit load of components with cracks or crack-like flaw. On the basis of linear elastic Finite Element Analysis (FEA), by specifying spatial variations in the elastic modulus, numerous sets of statically admissible and kinematically admissible distributions can be generated, to obtain lower and upper bounds limit loads. Due to the expected local plastic collapse, the reference volume concept is applied to identify the kinematically active and dead zones in the component. The Reference Volume Method is shown to yield a more accurate prediction of local limit loads. The limit load values are then compared with results obtained from inelastic FEA. The procedures are applied to a practical component with crack in order to verify their effectiveness in analyzing crack geometries. The analysis is then directed to geometries containing multiple cracks and three-dimensional defect in pressurized components.

scholarly journals Effect of Static Stretching with Superficial Cooling on Muscle Stiffness

2018 ◽  
Vol 02 (05) ◽  
pp. E142-E147 ◽  
Author(s):  
Masatoshi Nakamura ◽  
Ryo Hirabayashi ◽  
Shuhei Ohya ◽  
Takafumi Aoki ◽  
Daichi Suzuki ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Random Order ◽  
Acute Effect ◽  
Muscle Stiffness ◽  
Cooling Condition ◽  
Medial Gastrocnemius ◽  
Static Stretching ◽  
Shear Elastic Modulus ◽  
And Control ◽  
Healthy Males

AbstractThis study aimed to clarify the acute effect of static stretching (SS) with superficial cooling on dorsiflexion range of motion (DF ROM) and muscle stiffness. Sixteen healthy males participated in the cooling condition and a control condition in a random order. The DF ROM and the shear elastic modulus of medial gastrocnemius (MG) in the dominant leg were measured during passive dorsiflexion. All measurements were performed prior to (PRE) and immediately after 20 min of cooling or rested for 20 min (POST), followed by 2 min SS (POST SS). In cooling condition, DF ROM at POST and POST SS were significantly higher than that at PRE and DF ROM at POST SS was significantly higher than that at POST. In addition, the shear elastic modulus at POST was significantly higher than that at PRE and the shear elastic modulus at POST SS was significantly lower than those at PRE and POST. However, there were no significant differences in the percentage changes between PRE and POST SS between the cooling and control conditions. Our results showed that effects of SS with superficial cooling on increases in ROM and decrease in muscle stiffness were no more beneficial than those of SS alone.

scholarly journals In Vivo Reconstruction of the Acetabular Bone Defect by the Individualized Three-Dimensional Printed Porous Augment in a Swine Model

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Jun Fu ◽  
Yi Xiang ◽  
Ming Ni ◽  
Xiaojuan Qu ◽  
Yonggang Zhou ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Bone Defect ◽  
Bone Ingrowth ◽  
Structural Parameters ◽  
Three Dimensional ◽  
Acetabular Bone ◽  
Acetabular Bone Defect ◽  
3D Printed ◽  
Matching Degree

Background and Purpose. This study established an animal model of the acetabular bone defect in swine and evaluated the bone ingrowth, biomechanics, and matching degree of the individualized three-dimensional (3D) printed porous augment. Methods. As an acetabular bone defect model created in Bama miniswine, an augment individually fabricated by 3D print technique with Ti6Al4V powders was implanted to repair the defect. Nine swine were divided into three groups, including the immediate biomechanics group, 12-week biomechanics group, and 12-week histological group. The inner structural parameters of the 3D printed porous augment were measured by scanning electron microscopy (SEM), including porosity, pore size, and trabecular diameter. The matching degree between the postoperative augment and the designed augment was assessed by CT scanning and 3D reconstruction. In addition, biomechanical properties, such as stiffness, compressive strength, and the elastic modulus of the 3D printed porous augment, were measured by means of a mechanical testing machine. Moreover, bone ingrowth and implant osseointegration were histomorphometrically assessed. Results. In terms of the inner structural parameters of the 3D printed porous augment, the porosity was 55.48 ± 0.61 % , pore size 319.23 ± 25.05   μ m , and trabecular diameter 240.10 ± 23.50   μ m . Biomechanically, the stiffness was 21464.60 ± 1091.69   N / mm , compressive strength 231.10 ± 11.77   MPa , and elastic modulus 5.35 ± 0.23   GPa , respectively. Furthermore, the matching extent between the postoperative augment and the designed one was up to 91.40 ± 2.83 % . Besides, the maximal shear strength of the 3D printed augment was 929.46 ± 295.99   N immediately after implantation, whereas the strength was 1521.93 ± 98.38   N 12 weeks after surgery ( p = 0.0302 ). The bone mineral apposition rate (μm per day) 12 weeks post operation was 3.77 ± 0.93   μ m / d . The percentage bone volume of new bone was 22.30 ± 4.51 % 12 weeks after surgery. Conclusion. The 3D printed porous Ti6Al4V augment designed in this study was well biocompatible with bone tissue, possessed proper biomechanical features, and was anatomically well matched with the defect bone. Therefore, the 3D printed porous Ti6Al4V augment possesses great potential as an alternative for individualized treatment of severe acetabular bone defects.

scholarly journals Post-Operative Assessment of Ulnar Nerve Tension Using Shear-Wave Elastography

2021 ◽  
Vol 13 (3) ◽  
pp. 469-476
Author(s):  
Sebastien Durand ◽  
Wassim Raffoul ◽  
Thierry Christen ◽  
Nadine Pedrazzi
Keyword(s):  
Elastic Modulus ◽  
Shear Wave ◽  
Ulnar Nerve ◽  
Shear Wave Elastography ◽  
Elbow Flexion ◽  
Ulnar Nerve Compression ◽  
Nerve Decompression ◽  
Shear Elastic Modulus ◽  
Anterior Transposition ◽  
Operative Assessment

Background: Ulnar nerve compression at the elbow level is the second-most common entrapment neuropathy. The aim of this study was to use shear-wave elastography for the quantification of ulnar nerve elasticity in patients after ulnar nerve decompression with anterior transposition and in the contralateral non-operative side. Method: Eleven patients with confirmed diagnosis and ulnar nerve decompression with anterior transposition were included and examinations were performed on an AixplorerTM ultrasound system (Supersonic Imagine, Aix-en-Provence, France). Results: We observed significant differences at 0-degree (p < 0.001), 45-degree (p < 0.05), 90-degree (p < 0.01) and 120-degree (p < 0.001) elbow flexion in the shear elastic modulus of the ulnar nerve in the operative and non-operative sides. There were no statistically significant differences between the elasticity values of the ulnar nerve after transposition at 0-degree elbow flexion and in the non-operative side at 120-degree elbow flexion (p = 0.39), or in the ulnar nerve after transposition at 120-degree elbow flexion and in the non-operative side at 0-degree elbow flexion (p = 0.09). Conclusion: Shear-wave elastography has the potential to be used postoperatively as a method for assessing nerve tension noninvasively by the estimation of mechanical properties, such as the shear elastic modulus.

scholarly journals Modeling of the Mechanical Behavior of 3D Bioplotted Scaffolds Considering the Penetration in Interlocked Strands

2018 ◽  
Vol 8 (9) ◽  
pp. 1422 ◽  
Author(s):  
Saman Naghieh ◽  
M. Sarker ◽  
Mohammad Karamooz-Ravari ◽  
Adam McInnes ◽  
Xiongbiao Chen
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Model Development ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Hydrogel Scaffolds ◽  
Important Index ◽  
Geometrical Features ◽  
Scaffold Structure

Three-dimensional (3D) bioplotting has been widely used to print hydrogel scaffolds for tissue engineering applications. One issue involved in 3D bioplotting is to achieve the scaffold structure with the desired mechanical properties. To overcome this issue, various numerical methods have been developed to predict the mechanical properties of scaffolds, but limited by the imperfect representation of one key feature of scaffolds fabricated by 3D bioplotting, i.e., the penetration or fusion of strands in one layer into the previous layer. This paper presents our study on the development of a novel numerical model to predict the elastic modulus (one important index of mechanical properties) of 3D bioplotted scaffolds considering the aforementioned strand penetration. For this, the finite element method was used for the model development, while medium-viscosity alginate was selected for scaffold fabrication by the 3D bioplotting technique. The elastic modulus of the bioplotted scaffolds was characterized using mechanical testing and results were compared with those predicted from the developed model, demonstrating a strong congruity between them. Once validated, the developed model was also used to investigate the effect of other geometrical features on the mechanical behavior of bioplotted scaffolds. Our results show that the penetration, pore size, and number of printed layers have significant effects on the elastic modulus of bioplotted scaffolds; and also suggest that the developed model can be used as a powerful tool to modulate the mechanical behavior of bioplotted scaffolds.

Sign in / Sign up

Export Citation Format

Share Document