scholarly journals Active control of aircraft engine inlet noise using compact sound sources and distributed error sensors

1995 ◽  
Vol 98 (1) ◽  
pp. 27-27
Author(s):  
Ricardo Burdisso ◽  
Chris R. Fuller
Keyword(s):  
Active Control ◽  
Aircraft Engine ◽  
Sound Sources

Production and active control of microbubbles aggregations in artificial capillary with multiple sound sources

2012 ◽  
Author(s):  
Kohji Masuda ◽  
Nobuhiko Shigehara ◽  
Ren Koda ◽  
Nobuyuki Watarai ◽  
Seiichi Ikeda ◽  
...  
Keyword(s):  
Active Control ◽  
Sound Sources ◽  
Artificial Capillary

Active Control of Low-Frequency Sound Radiation From Vibrating Panel Using Planar Sound Sources

2001 ◽  
Vol 124 (1) ◽  
pp. 2-9 ◽  
Author(s):  
Kean Chen ◽  
Gary H. Koopmann
Keyword(s):  
Active Control ◽  
Near Field ◽  
Low Frequency ◽  
Sound Radiation ◽  
Sound Field ◽  
Sound Power ◽  
Frequency Range ◽  
Sound Sources ◽  
Frequency Sound ◽  
Secondary Sources

Active control of low frequency sound radiation using planar secondary sources is theoretically investigated in this paper. The primary sound field originates from a vibrating panel and the planar sources are modeled as simply supported rectangular panels in an infinite baffle. The sound power of the primary and secondary panels are calculated using a near field approach, and then a series of formulas are derived to obtain the optimum reduction in sound power based on minimization of the total radiate sound power. Finally, active reduction for a number of secondary panel arrangements is examined and it is concluded that when the modal distribution of the secondary panel does not coincide with that of the primary panel, one secondary panel is sufficient. Otherwise four secondary panels can guarantee considerable reduction in sound power over entire frequency range of interest.

High-Temperature Instability of A Cr2Nb-Nb(Cr) Microlaminate Composite

1996 ◽  
Vol 54 ◽  
pp. 374-375
Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Aircraft Engine ◽  
Lattice Parameter ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Cross Sectional ◽  
Bcc Structure

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.

Sign in / Sign up

Export Citation Format

Share Document