Ultrasonic airborne insertion loss measurements at normal incidence (L)

2010 ◽  
Vol 128 (6) ◽  
pp. 3305-3307 ◽  
Author(s):  
Jayrin Farley ◽  
Brian E. Anderson
Keyword(s):  
Insertion Loss ◽  
Normal Incidence

Analysis of Contrast Reversal in SEM Images

1972 ◽  
Vol 30 ◽  
pp. 398-399
Author(s):  
M. D. Coutts ◽  
E. R. Levin
Keyword(s):  
Incident Beam ◽  
Normal Incidence ◽  
Beam Current ◽  
Secondary Emission ◽  
Image Contrast ◽  
Sem Images ◽  
Secondary Electrons ◽  
Image Position

On tilting samples in an SEM, the image contrast between two elements, x and y often decreases to zero at θε, which we call the no-contrast angle. At angles above θε the contrast is reversed, θ being the angle between the specimen normal and the incident beam. The available contrast between two elements, x and y, in the SEM can be defined as,(1)where ix and iy are the total number of reflected and secondary electrons, leaving x and y respectively. It can easily be shown that for the element x,(2)where ib is the beam current, isp the specimen absorbed current, δo the secondary emission at normal incidence, k is a constant, and m the reflected electron coefficient.

Characterization of Rh/Si multilayer structure by HREM and HAADF

1992 ◽  
Vol 50 (1) ◽  
pp. 122-123
Author(s):  
Y. Cheng ◽  
J. Liu ◽  
M.B. Stearns ◽  
D.G. Steams
Keyword(s):  
Normal Incidence ◽  
High Resolution Electron Microscopy ◽  
X Rays ◽  
Beam Direction ◽  
Cross Sectional ◽  
Optical Elements ◽  
Resolution Electron ◽  
Point To Point ◽  
Better Than

The Rh/Si multilayer (ML) thin films are promising optical elements for soft x-rays since they have a calculated normal incidence reflectivity of ∼60% at a x-ray wavelength of ∼13 nm. However, a reflectivity of only 28% has been attained to date for ML fabricated by dc magnetron sputtering. In order to determine the cause of this degraded reflectivity the microstructure of this ML was examined on cross-sectional specimens with two high-resolution electron microscopy (HREM and HAADF) techniques.Cross-sectional specimens were made from an as-prepared ML sample and from the same ML annealed at 298 °C for 1 and 100 hours. The specimens were imaged using a JEM-4000EX TEM operating at 400 kV with a point-to-point resolution of better than 0.17 nm. The specimens were viewed along Si [110] projection of the substrate, with the (001) Si surface plane parallel to the beam direction.

On resolving fine periodic microstructures in the optical microscope

1989 ◽  
Vol 47 ◽  
pp. 364-365
Author(s):  
W.S. Putnam ◽  
C. Viney
Keyword(s):  
Liquid Crystalline ◽  
Numerical Aperture ◽  
Polarized Light ◽  
Normal Incidence ◽  
Optical Microscope ◽  
Angle Of Incidence ◽  
Resolution Limit ◽  
Crystalline Materials ◽  
Periodic Microstructures ◽  
Liquid Crystalline Materials

Many sheared liquid crystalline materials (fibers, films and moldings) exhibit a fine banded microstructure when observed in the polarized light microscope. In some cases, for example Kevlar® fiber, the periodicity is close to the resolution limit of even the highest numerical aperture objectives. The periodic microstructure reflects a non-uniform alignment of the constituent molecules, and consequently is an indication that the mechanical properties will be less than optimal. Thus it is necessary to obtain quality micrographs for characterization, which in turn requires that fine detail should contribute significantly to image formation.It is textbook knowledge that the resolution achievable with a given microscope objective (numerical aperture NA) and a given wavelength of light (λ) increases as the angle of incidence of light at the specimen surface is increased. Stated in terms of the Abbe resolution criterion, resolution improves from λ/NA to λ/2NA with increasing departure from normal incidence.

Microspectroscopy Using a Solid Immersion Lens

2001 ◽  
Vol 7 (S2) ◽  
pp. 148-149
Author(s):  
C.D. Poweleit ◽  
J Menéndez
Keyword(s):  
Spatial Resolution ◽  
Focal Plane ◽  
Numerical Aperture ◽  
Normal Incidence ◽  
Spot Size ◽  
Index Of Refraction ◽  
Objective Lens ◽  
Improvement Factor ◽  
Oil Immersion ◽  
Long Time

Oil immersion lenses have been used in optical microscopy for a long time. The light’s wavelength is decreased by the oil’s index of refraction n and this reduces the minimum spot size. Additionally, the oil medium allows a larger collection angle, thereby increasing the numerical aperture. The SIL is based on the same principle, but offers more flexibility because the higher index material is solid. in particular, SILs can be deployed in cryogenic environments. Using a hemispherical glass the spatial resolution is improved by a factor n with respect to the resolution obtained with the microscope’s objective lens alone. The improvement factor is equal to n2 for truncated spheres.As shown in Fig. 1, the hemisphere SIL is in contact with the sample and does not affect the position of the focal plane. The focused rays from the objective strike the lens at normal incidence, so that no refraction takes place.

SOFT X-RAY IMAGES OF THE SOLAR CORONA USING NORMAL INCIDENCE OPTICS

1988 ◽  
Vol 49 (C1) ◽  
pp. C1-115-C1-118 ◽  
Author(s):  
M. E. BRUNER ◽  
B. M. HAISCH ◽  
W. A. BROWN ◽  
L. W. ACTON ◽  
J. H. UNDERWOOD
Keyword(s):  
Solar Corona ◽  
Normal Incidence ◽  
X Ray

Method for Evaluating Insertion Loss of EMI Filter Connected to Semiconductor Power Converters

2012 ◽  
Vol 132 (7) ◽  
pp. 727-735 ◽  
Author(s):  
Michio Tamate ◽  
Tamiko Sasaki ◽  
Akio Toba ◽  
Yasushi Matsumoto ◽  
Keiji Wada ◽  
...  
Keyword(s):  
Insertion Loss ◽  
Power Converters ◽  
Emi Filter

Performance and Reliability of a MEMS-based tunable optical filter operating in the 1565 nm-1525 nm wavelength range

2002 ◽  
Vol 722 ◽  
Author(s):  
T. S. Sriram ◽  
B. Strauss ◽  
S. Pappas ◽  
A. Baliga ◽  
A. Jean ◽  
...  
Keyword(s):  
Silicon Nitride ◽  
Line Width ◽  
Insertion Loss ◽  
Optical Filter ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Reliability Testing ◽  
Silicon Nitride Membrane ◽  
Tunable Optical Filter ◽  
Extensive Performance

AbstractThis paper describes the results of extensive performance and reliability characterization of a silicon-based surface micro-machined tunable optical filter. The device comprises a high-finesse Fabry-Perot etalon with one flat and one curved dielectric mirror. The curved mirror is mounted on an electrostatically actuated silicon nitride membrane tethered to the substrate using silicon nitride posts. A voltage applied to the membrane allows the device to be tuned by adjusting the length of the cavity. The device is coupled optically to an input and an output single mode fiber inside a hermetic package. Extensive performance characterization (over operating temperature range) was performed on the packaged device. Parameters characterized included tuning characteristics, insertion loss, filter line-width and side mode suppression ratio. Reliability testing was performed by subjecting the MEMS structure to a very large number of actuations at an elevated temperature both inside the package and on a test board. The MEMS structure was found to be extremely robust, running trillions of actuations without failures. Package level reliability testing conforming to Telcordia standards indicated that key device parameters including insertion loss, filter line-width and tuning characteristics did not change measurably over the duration of the test.

Sign in / Sign up

Export Citation Format

Share Document