Degradation of Terfenol-D particle epoxy composites under low-frequency cyclic magneto-mechanical loading at the matrix glass transition start and finish temperatures

2004 ◽  
Author(s):  
William D. Armstrong ◽  
Manikantan Shanmugham ◽  
Harold Bailey
Keyword(s):  
Glass Transition ◽  
Mechanical Loading ◽  
Low Frequency ◽  
Epoxy Composites ◽  
Matrix Glass ◽  
The Matrix

scholarly journals Tunable characteristics of low-frequency bandgaps in two-dimensional multivibrator phononic crystal plates under prestrain

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Hai-Fei Zhu ◽  
Xiao-Wei Sun ◽  
Ting Song ◽  
Xiao-Dong Wen ◽  
Xi-Xuan Liu ◽  
...  
Keyword(s):  
Phononic Crystal ◽  
Real Life ◽  
Low Frequency ◽  
Acoustic Vibration ◽  
Crystal Plate ◽  
Frequency Noise ◽  
Two Dimensional ◽  
The Matrix ◽  
Noise Frequency ◽  
Realtime Control

AbstractIn view of the influence of variability of low-frequency noise frequency on noise prevention in real life, we present a novel two-dimensional tunable phononic crystal plate which is consisted of lead columns deposited in a silicone rubber plate with periodic holes and calculate its bandgap characteristics by finite element method. The low-frequency bandgap mechanism of the designed model is discussed simultaneously. Accordingly, the influence of geometric parameters of the phononic crystal plate on the bandgap characteristics is analyzed and the bandgap adjustability under prestretch strain is further studied. Results show that the new designed phononic crystal plate has lower bandgap starting frequency and wider bandwidth than the traditional single-sided structure, which is due to the coupling between the resonance mode of the scatterer and the long traveling wave in the matrix with the introduction of periodic holes. Applying prestretch strain to the matrix can realize active realtime control of low-frequency bandgap under slight deformation and broaden the low-frequency bandgap, which can be explained as the multiple bands tend to be flattened due to the localization degree of unit cell vibration increases with the rise of prestrain. The presented structure improves the realtime adjustability of sound isolation and vibration reduction frequency for phononic crystal in complex acoustic vibration environments.

Comparison of Magnetostrictive Performance Loss of Particulate Tb0.3 Dy0.7 Fe2 Epoxy Composites Prepared with Different Matrix Polymers M. Shanmugham et al.: Comparison of Magnetostrictive Performance Loss of Particulate Tb0.3 Dy0.7 Fe2 Epoxy Composites

2004 ◽  
Vol 19 (3) ◽  
pp. 795-805 ◽  
Author(s):  
Manikantan Shanmugham ◽  
Harold Bailey ◽  
William D. Armstrong
Keyword(s):  
Magnetic Field ◽  
Glass Transition ◽  
Matrix Material ◽  
Epoxy Composites ◽  
Particulate Composites ◽  
Specimen Preparation ◽  
Performance Loss ◽  
Magnetostrictive Strain ◽  
Relative Damage ◽  
Low Modulus

Particulate composites of magnetostrictive Terfenol-D were prepared with polyamine and anhydride cured epoxy polymer matrices with the presence or the absence of a strong magnetic field. These composites were studied to investigate (i) the influence of magnetic field that is applied during specimen preparation in strain output levels, (ii) performance loss at high temperatures, and (iii) the influence of matrix material in magnetostrictive strain performance. A six-way comparison is made of materials processed under magnetic field with materials processed under no magnetic field, and magnetostrictive strain performance at glass transition finish temperature with magnetostrictive strain performance at glass transition start temperature, and magnetostrictive strain performance in low modulus matrix systems with magnetostrictive strain performance in high modulus matrix systems. A four-way comparison is also made between the micrographs for strain-cycled and non-strain-cycled samples and relative damage incurred by samples prepared using high and low modulus matrix systems.

A Raman study of B203 through the liquid-glass transition range

1992 ◽  
Vol 02 ◽  
pp. C2-265-C2-270
Author(s):  
A. K. HASSAN ◽  
L. M. TORELL ◽  
L. BORJESSON
Keyword(s):  
Glass Transition ◽  
Correlation Length ◽  
Room Temperature ◽  
Vibrational Mode ◽  
Low Frequency ◽  
Boson Peak ◽  
Transition Range ◽  
Structural Correlation ◽  
Raman Study ◽  
Correlation Range

The low frequency Raman spectrum of B203 and the boroxol ring vibrational mode at 808 cm-1 have been studied from room temperature to 1273 K as the glass transforms to a melt. Both the low frequeney "boson" peak and the boroxol mode are markedly influenced by the glass transition. Raising the temperature above Tg the strength of the 808 cm-1 mode decreases linearly indicating the Similar behavior of the boroxol ring concentration. The boson peak shows a different temperature behavior, which mirrors that of the sound velo city. The structural correlation length demostrates the same correlation range in the liquid and the glass. The results, when compared with neutron diffraction measurements contradict a recently proposed relation between the "boson correlation length" and the position of the first sharp diffraction peak of the structure factor.

Ballistic impact response of carbon/epoxy tubes with variable nanosilica content

2017 ◽  
Vol 52 (12) ◽  
pp. 1589-1604 ◽  
Author(s):  
Aniruddh Vashisth ◽  
Charles E Bakis ◽  
Charles R Ruggeri ◽  
Todd C Henry ◽  
Gary D Roberts
Keyword(s):  
Fracture Toughness ◽  
Shear Strength ◽  
Glass Transition ◽  
Transition Temperature ◽  
Impact Damage ◽  
Mass Density ◽  
Impact Response ◽  
Residual Shear Strength ◽  
Damage Area ◽  
The Matrix

Laminated fiber reinforced polymer composites are known for high specific strength and stiffness in the plane of lamination, yet relatively low out-of-plane impact damage tolerance due to matrix dominated interlaminar mechanical properties. A number of factors including the toughness of the matrix can influence the response of composites to impact. The objective of the current investigation is to evaluate the ballistic impact response of carbon/epoxy tubes with variable amounts of nanosilica particles added to the matrix as a toughening agent. Mass density, elastic modulus, glass transition temperature and Mode I fracture toughness of the matrix materials were measured. Tubes manufactured with these matrix materials were ballistically impacted using a round steel projectile aimed at normal incidence across the major diameter. After impact, the tubes were nondestructively inspected and subjected to mechanical tests to determine the residual shear strength in torsion. Increasing concentrations of nanosilica monotonically increased the modulus and fracture toughness of the matrix materials. Tubes with nanosilica had smaller impact damage area, higher residual shear strength, and higher energy absorbed per unit damage area versus control materials with no nanosilica. Overall, the addition of nanosilica improved the impact damage resistance and tolerance of carbon/epoxy tubes loaded in torsion, with minimal adverse effects on mass density and glass transition temperature.

Sign in / Sign up

Export Citation Format

Share Document