How to report light loss values for optical fibers used in fiber optic lighting applications

1998 ◽  
Author(s):  
Andrew Bierman ◽  
Nadarajah Narendran ◽  
Nishantha Maliyagoda
Keyword(s):  
Optical Fibers ◽  
Fiber Optic ◽  
Light Loss

High-voltage monitoring by the fiber-optic recirculating measuring system

2020 ◽  
pp. 38-44
Author(s):  
A. V. Polyakov ◽  
M. A. Ksenofontov
Keyword(s):  
Optical Fibers ◽  
High Voltage ◽  
Optical Sensors ◽  
Electromagnetic Interference ◽  
Fiber Optic ◽  
Electric Power Industry ◽  
Measuring System ◽  
Voltage Range ◽  
External Electromagnetic Fields ◽  
Optic Communication

Optical technologies for measuring electrical quantities attract great attention due to their unique properties and significant advantages over other technologies used in high-voltage electric power industry: the use of optical fibers ensures high stability of measuring equipment to electromagnetic interference and galvanic isolation of high-voltage sensors; external electromagnetic fields do not influence the data transmitted from optical sensors via fiber-optic communication lines; problems associated with ground loops are eliminated, there are no side electromagnetic radiation and crosstalk between the channels. The structure and operation principle of a quasi-distributed fiber-optic high-voltage monitoring system is presented. The sensitive element is a combination of a piezo-ceramic tube with an optical fiber wound around it. The device uses reverse transverse piezoelectric effect. The measurement principle is based on recording the change in the recirculation frequency under the applied voltage influence. When the measuring sections are arranged in ascending order of the measured effective voltages relative to the receiving-transmitting unit, a relative resolution of 0,3–0,45 % is achieved for the PZT-5H and 0,8–1,2 % for the PZT-4 in the voltage range 20–150 kV.

scholarly journals Sensing, Actuation, and Control of the SmartX Prototype Morphing Wing in the Wind Tunnel

Actuators ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 107
Author(s):  
Nakash Nazeer ◽  
Xuerui Wang ◽  
Roger M. Groves
Keyword(s):  
Wind Tunnel ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Experimental Testing ◽  
Single Mode ◽  
Fiber Optic Sensor ◽  
Sensor Data ◽  
Random Errors ◽  
Morphing Wing ◽  
Actuator Dynamics

This paper presents a study on trailing edge deflection estimation for the SmartX camber morphing wing demonstrator. This demonstrator integrates the technologies of smart sensing, smart actuation and smart controls using a six module distributed morphing concept. The morphing sequence is brought about by two actuators present at both ends of each of the morphing modules. The deflection estimation is carried out by interrogating optical fibers that are bonded on to the wing’s inner surface. A novel application is demonstrated using this method that utilizes the least amount of sensors for load monitoring purposes. The fiber optic sensor data is used to measure the deflections of the modules in the wind tunnel using a multi-modal fiber optic sensing approach and is compared to the deflections estimated by the actuators. Each module is probed by single-mode optical fibers that contain just four grating sensors and consider both bending and torsional deformations. The fiber optic method in this work combines the principles of hybrid interferometry and FBG spectral sensing. The analysis involves an initial calibration procedure outside the wind tunnel followed by experimental testing in the wind tunnel. This method is shown to experimentally achieve an accuracy of 2.8 mm deflection with an error of 9%. The error sources, including actuator dynamics, random errors, and nonlinear mechanical backlash, are identified and discussed.

scholarly journals Novel Bloch wave excitation platform based on few-layer photonic crystal deposited on D-shaped optical fiber

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Esteban Gonzalez-Valencia ◽  
Ignacio Del Villar ◽  
Pedro Torres
Keyword(s):  
Optical Fibers ◽  
High Performance ◽  
Light Propagation ◽  
Fiber Optic ◽  
Layer Structure ◽  
Optical Network ◽  
Building Blocks ◽  
Bloch Wave ◽  
Nanophotonic Devices ◽  
Wide Range

AbstractWith the goal of ultimate control over the light propagation, photonic crystals currently represent the primary building blocks for novel nanophotonic devices. Bloch surface waves (BSWs) in periodic dielectric multilayer structures with a surface defect is a well-known phenomenon, which implies new opportunities for controlling the light propagation and has many applications in the physical and biological science. However, most of the reported structures based on BSWs require depositing a large number of alternating layers or exploiting a large refractive index (RI) contrast between the materials constituting the multilayer structure, thereby increasing the complexity and costs of manufacturing. The combination of fiber–optic-based platforms with nanotechnology is opening the opportunity for the development of high-performance photonic devices that enhance the light-matter interaction in a strong way compared to other optical platforms. Here, we report a BSW-supporting platform that uses geometrically modified commercial optical fibers such as D-shaped optical fibers, where a few-layer structure is deposited on its flat surface using metal oxides with a moderate difference in RI. In this novel fiber optic platform, BSWs are excited through the evanescent field of the core-guided fundamental mode, which indicates that the structure proposed here can be used as a sensing probe, along with other intrinsic properties of fiber optic sensors, as lightness, multiplexing capacity and easiness of integration in an optical network. As a demonstration, fiber optic BSW excitation is shown to be suitable for measuring RI variations. The designed structure is easy to manufacture and could be adapted to a wide range of applications in the fields of telecommunications, environment, health, and material characterization.

scholarly journals Analysis of Curvature in Fiber Optic Cable for Macrobending-Based Slope Sensor

2021 ◽  
Vol 3 (1) ◽  
pp. 45-56
Author(s):  
Imam Mulyanto
Keyword(s):  
Fiber Optics ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Laser Light ◽  
Laser Intensity ◽  
Single Mode ◽  
Power Losses ◽  
Fiber Optic Cable ◽  
Power Meter ◽  
Working Principle

The analysis of fiber optics for macro bending-based slope sensors using SMF-28 single-mode optical fibers has been successfully conducted. Fiber optics were treated to silicon rubber molding and connected with laser light and power meters to measure the intensity of laser power generated. The working principle was carried out using the macrobending phenomenon on single-mode optical fibers. The intensity of laser light in fiber optic cables decreases in the event of indentation or bending of the fiber optic cable. Power losses resulting from the macrobending process can be seen in the result of the information sensitivity of fiber optics to the change of angle given. From the results of the study, the resulting fiber optic sensitivity value is -0.1534o/dBm. The larger the angle given, the lower the laser intensity received by the power meter.

scholarly journals Macrobending Loss Analysis on Singlemode-Multimode-Singlemode Fiber Optic Core

2019 ◽  
Vol 9 (2) ◽  
pp. 11-15
Author(s):  
Sisca Arisya Harry Andhina
Keyword(s):  
Light Source ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Optical Power ◽  
Single Mode ◽  
Fiber Optic Cable ◽  
Power Meter ◽  
Loss Analysis ◽  
Measurement Results ◽  
Source Test

Macrobending often occurs in optical fibers that embedded in the ground due to shifting of soil or rocks in the ground causing interference in transmission. In this study used single-mode-multimode-singlemode fiber optic cable connected manually and axially measured using a light source test equipment and optical power meter and the results will be compared. The measurement results obtained the greater  value of macrobending losses with the smaller the diameter of the winding, and the greater the number of turns. The highest value of macrobending losses in multimode cables is -1.48dB at 0.5cm diameter with 5 turns, highest value of macrobending losses on single mode cables is -12.73dB at 0.5cm diameter with 5 turns,  lowest value of macrobending losses for multimode cables is -0.44dB at 5cm diameter with 1 twist, lowest macrobending losses in singlemode cables is -1.69dB at 5cm diameter with 1 twist. While the value of macrobending losses on axially connected SMS cables shows the highest value of macrobending losses on multimode cables is -1.12dB in diameter of 0.5cm with 5 turns,  highest value of macrobending losses on singlemode cables is -1.18dB at diameter of 0.5cm with 5 turns,  lowest value for macrobending losses on multimode cables is -0.66dB at 5cm in diameter with 1 twist, the smallest value for macrobending losses on singlemode cables is -0.27dB at 5cm diameter with 1 twist . The measurement results also showed that the macrobending losses of manually connected SMS cables were greater than the macrobending losses of axially connected SMS cables.

scholarly journals High-Sensitivity Fiber-Optic Ultrasound Sensors for Medical Imaging Applications

1998 ◽  
Vol 20 (2) ◽  
pp. 103-112 ◽  
Author(s):  
H. Wen ◽  
D.G. Wiesler ◽  
A. Tveten ◽  
B. Danver ◽  
A. Dandridge
Keyword(s):  
Medical Imaging ◽  
Optical Fibers ◽  
Electromagnetic Interference ◽  
Fiber Optic ◽  
High Sensitivity ◽  
Single Mode ◽  
Piezoelectric Sensors ◽  
Single Element ◽  
Bending Radius ◽  
Laser Interferometers

This paper presents several designs of high-sensitivity, compact fiber-optic ultrasound sensors that may be used for medical imaging applications. These sensors translate ultrasonic pulses into strains in single-mode optical fibers, which are measured with fiber-based laser interferometers at high precision. The sensors are simpler and less expensive to make than piezoelectric sensors, and are not susceptible to electromagnetic interference. It is possible to make focal sensors with these designs, and several schemes are discussed. Because of the minimum bending radius of optical fibers, the designs are suitable for single element sensors rather than for arrays.

Automated Fiber-Optic System for Monitoring the Stability of the Pit Quarry Mass and Dumps

2021 ◽  
pp. 19-26
Author(s):  
А.D. Меkhtiyev ◽  
◽  
E.G. Neshina ◽  
P.Sh. Madi ◽  
D.A. Gorokhov ◽  
...  
Keyword(s):  
Rock Mass ◽  
Optical Fiber ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Light Wave ◽  
Single Mode ◽  
Fiber Optic Sensors ◽  
Fiber Optic Sensor ◽  
Laboratory Sample ◽  
Single Mode Optical Fiber

This article ls with the issues related to the development of a system for monitoring the deformation and displacement of the rock mass leading to the collapse of the quarry sides. Monitoring system uses point-to-point fiber-optic sensors. Fiber-optic sensors and control cables of the communication line are made based on the single mode optical fibers, which allows to measure with high accuracy the deformations and displacements of the rock mass at a distance of 30-50 km. To create fiber-optic pressure sensors, an optical fiber of the ITU-T G. 652.D standard is used. Laboratory sample is developed concerning the point fiber-optic sensor made based on the two-arm Mach-Zender interferometer using a single mode optical fiber for monitoring strain (displacements) with a change in the sensitivity and a reduced influence of temperature interference leading to zero drift. The article presents a mathematical apparatus for calculating the intensity of radiation of a light wave passing through an optical fiber with and without mechanical stress. A laboratory sample of single mode optical fibers based on the Mach-Zender interferometer showed a fairly high linearity and accuracy in the measurement and can be used to control the strain of the mass after appropriate refinement of its design. Mathematical expressions are also given for determining the intensity of the light wave when the distance between the fixing points of a single mode optical fiber changes depending on the change in the external temperature. A diagram for measuring strain using a point fiber-optic strain sensor is developed. Hardware and software package is developed, which can be used to perform a number of settings of measuring channels. The work is aimed at solving the production problems of the Kenzhem quarry of AK Altynalmas JSC.

A Step-Index Multimode Fiber-Optic Microbend Displacement Sensor Wavelength Dependent Loss

2019 ◽  
pp. 47-60
Author(s):  
Sami D. Alaruri
Keyword(s):  
Optical Fibers ◽  
Fiber Optic ◽  
Transmission Loss ◽  
Wavelength Dependence ◽  
Fiber Optic Sensors ◽  
Fused Silica ◽  
Displacement Sensor ◽  
Sensor Output ◽  
Core Diameter ◽  
Step Index

In this chapter, the wavelength dependence of bend loss in a step-index multimode optical fiber (100 µm core diameter; fused silica) was investigated for fiber bend radii ranging between 2.0 and 4.5 mm using six laser excitation wavelengths, namely, 337.1, 470, 590, 632.8, 750, and 810 nm. The results obtained from fitting the bend loss measurements to Kao's model and utilizing MATLAB® indicate that bend loss is wavelength dependent and transmission loss in multimode optical fibers increases with the decrease in the fiber bend radius. Furthermore, the response of a microbend fiber-optic displacement sensor was characterized at 337.1, 470, 632.8, 750, and 810 nm. Measurements obtained from the microbend sensor indicate that the sensor output power is linear with the applied displacement and the sensor output is wavelength dependent. Lastly, references for industrial and biomedical applications of microbend fiber-optic sensors are provided. Finally, a brief description for the transmission loss mechanisms in optical fibers is given.

Sign in / Sign up

Export Citation Format

Share Document