scholarly journals Sensing, Actuation, and Control of the SmartX Prototype Morphing Wing in the Wind Tunnel

Actuators ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 107
Author(s):  
Nakash Nazeer ◽  
Xuerui Wang ◽  
Roger M. Groves
Keyword(s):  
Wind Tunnel ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Experimental Testing ◽  
Single Mode ◽  
Fiber Optic Sensor ◽  
Sensor Data ◽  
Random Errors ◽  
Morphing Wing ◽  
Actuator Dynamics

This paper presents a study on trailing edge deflection estimation for the SmartX camber morphing wing demonstrator. This demonstrator integrates the technologies of smart sensing, smart actuation and smart controls using a six module distributed morphing concept. The morphing sequence is brought about by two actuators present at both ends of each of the morphing modules. The deflection estimation is carried out by interrogating optical fibers that are bonded on to the wing’s inner surface. A novel application is demonstrated using this method that utilizes the least amount of sensors for load monitoring purposes. The fiber optic sensor data is used to measure the deflections of the modules in the wind tunnel using a multi-modal fiber optic sensing approach and is compared to the deflections estimated by the actuators. Each module is probed by single-mode optical fibers that contain just four grating sensors and consider both bending and torsional deformations. The fiber optic method in this work combines the principles of hybrid interferometry and FBG spectral sensing. The analysis involves an initial calibration procedure outside the wind tunnel followed by experimental testing in the wind tunnel. This method is shown to experimentally achieve an accuracy of 2.8 mm deflection with an error of 9%. The error sources, including actuator dynamics, random errors, and nonlinear mechanical backlash, are identified and discussed.

Automated Fiber-Optic System for Monitoring the Stability of the Pit Quarry Mass and Dumps

2021 ◽  
pp. 19-26
Author(s):  
А.D. Меkhtiyev ◽  
◽  
E.G. Neshina ◽  
P.Sh. Madi ◽  
D.A. Gorokhov ◽  
...  
Keyword(s):  
Rock Mass ◽  
Optical Fiber ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Light Wave ◽  
Single Mode ◽  
Fiber Optic Sensors ◽  
Fiber Optic Sensor ◽  
Laboratory Sample ◽  
Single Mode Optical Fiber

This article ls with the issues related to the development of a system for monitoring the deformation and displacement of the rock mass leading to the collapse of the quarry sides. Monitoring system uses point-to-point fiber-optic sensors. Fiber-optic sensors and control cables of the communication line are made based on the single mode optical fibers, which allows to measure with high accuracy the deformations and displacements of the rock mass at a distance of 30-50 km. To create fiber-optic pressure sensors, an optical fiber of the ITU-T G. 652.D standard is used. Laboratory sample is developed concerning the point fiber-optic sensor made based on the two-arm Mach-Zender interferometer using a single mode optical fiber for monitoring strain (displacements) with a change in the sensitivity and a reduced influence of temperature interference leading to zero drift. The article presents a mathematical apparatus for calculating the intensity of radiation of a light wave passing through an optical fiber with and without mechanical stress. A laboratory sample of single mode optical fibers based on the Mach-Zender interferometer showed a fairly high linearity and accuracy in the measurement and can be used to control the strain of the mass after appropriate refinement of its design. Mathematical expressions are also given for determining the intensity of the light wave when the distance between the fixing points of a single mode optical fiber changes depending on the change in the external temperature. A diagram for measuring strain using a point fiber-optic strain sensor is developed. Hardware and software package is developed, which can be used to perform a number of settings of measuring channels. The work is aimed at solving the production problems of the Kenzhem quarry of AK Altynalmas JSC.

Identification of trespasser from the signatures of buried single mode fiber optic sensor cable

2015 ◽  
Author(s):  
Preetam Suman ◽  
Pallavi Gupta ◽  
Philip B. Kassey ◽  
Neera Saxena ◽  
Yogesh Choudhary ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fiber Optic Sensor ◽  
Optic Sensor

scholarly journals Analysis of Curvature in Fiber Optic Cable for Macrobending-Based Slope Sensor

2021 ◽  
Vol 3 (1) ◽  
pp. 45-56
Author(s):  
Imam Mulyanto
Keyword(s):  
Fiber Optics ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Laser Light ◽  
Laser Intensity ◽  
Single Mode ◽  
Power Losses ◽  
Fiber Optic Cable ◽  
Power Meter ◽  
Working Principle

The analysis of fiber optics for macro bending-based slope sensors using SMF-28 single-mode optical fibers has been successfully conducted. Fiber optics were treated to silicon rubber molding and connected with laser light and power meters to measure the intensity of laser power generated. The working principle was carried out using the macrobending phenomenon on single-mode optical fibers. The intensity of laser light in fiber optic cables decreases in the event of indentation or bending of the fiber optic cable. Power losses resulting from the macrobending process can be seen in the result of the information sensitivity of fiber optics to the change of angle given. From the results of the study, the resulting fiber optic sensitivity value is -0.1534o/dBm. The larger the angle given, the lower the laser intensity received by the power meter.

scholarly journals Macrobending Loss Analysis on Singlemode-Multimode-Singlemode Fiber Optic Core

2019 ◽  
Vol 9 (2) ◽  
pp. 11-15
Author(s):  
Sisca Arisya Harry Andhina
Keyword(s):  
Light Source ◽  
Optical Fibers ◽  
Fiber Optic ◽  
Optical Power ◽  
Single Mode ◽  
Fiber Optic Cable ◽  
Power Meter ◽  
Loss Analysis ◽  
Measurement Results ◽  
Source Test

Macrobending often occurs in optical fibers that embedded in the ground due to shifting of soil or rocks in the ground causing interference in transmission. In this study used single-mode-multimode-singlemode fiber optic cable connected manually and axially measured using a light source test equipment and optical power meter and the results will be compared. The measurement results obtained the greater  value of macrobending losses with the smaller the diameter of the winding, and the greater the number of turns. The highest value of macrobending losses in multimode cables is -1.48dB at 0.5cm diameter with 5 turns, highest value of macrobending losses on single mode cables is -12.73dB at 0.5cm diameter with 5 turns,  lowest value of macrobending losses for multimode cables is -0.44dB at 5cm diameter with 1 twist, lowest macrobending losses in singlemode cables is -1.69dB at 5cm diameter with 1 twist. While the value of macrobending losses on axially connected SMS cables shows the highest value of macrobending losses on multimode cables is -1.12dB in diameter of 0.5cm with 5 turns,  highest value of macrobending losses on singlemode cables is -1.18dB at diameter of 0.5cm with 5 turns,  lowest value for macrobending losses on multimode cables is -0.66dB at 5cm in diameter with 1 twist, the smallest value for macrobending losses on singlemode cables is -0.27dB at 5cm diameter with 1 twist . The measurement results also showed that the macrobending losses of manually connected SMS cables were greater than the macrobending losses of axially connected SMS cables.

scholarly journals High-Sensitivity Fiber-Optic Ultrasound Sensors for Medical Imaging Applications

1998 ◽  
Vol 20 (2) ◽  
pp. 103-112 ◽  
Author(s):  
H. Wen ◽  
D.G. Wiesler ◽  
A. Tveten ◽  
B. Danver ◽  
A. Dandridge
Keyword(s):  
Medical Imaging ◽  
Optical Fibers ◽  
Electromagnetic Interference ◽  
Fiber Optic ◽  
High Sensitivity ◽  
Single Mode ◽  
Piezoelectric Sensors ◽  
Single Element ◽  
Bending Radius ◽  
Laser Interferometers

This paper presents several designs of high-sensitivity, compact fiber-optic ultrasound sensors that may be used for medical imaging applications. These sensors translate ultrasonic pulses into strains in single-mode optical fibers, which are measured with fiber-based laser interferometers at high precision. The sensors are simpler and less expensive to make than piezoelectric sensors, and are not susceptible to electromagnetic interference. It is possible to make focal sensors with these designs, and several schemes are discussed. Because of the minimum bending radius of optical fibers, the designs are suitable for single element sensors rather than for arrays.

Novel morphing wing actuator control-based Particle Swarm Optimisation

2019 ◽  
Vol 124 (1271) ◽  
pp. 55-75 ◽  
Author(s):  
S. Khan ◽  
T. L. Grigorie ◽  
R. M. Botez ◽  
M. Mamou ◽  
Y. Mébarki
Keyword(s):  
Control System ◽  
Wind Tunnel ◽  
Experimental Model ◽  
Experimental Testing ◽  
Pressure Sensors ◽  
Particle Swarm ◽  
Particle Swarm Optimisation ◽  
Morphing Wing ◽  
Software Model ◽  
Actuation System

AbstractThe paper presents the design and experimental testing of the control system used in a new morphing wing application with a full-scaled portion of a real wing. The morphing actuation system uses four similar miniature brushless DC (BLDC) motors placed inside the wing, which execute a direct actuation of the flexible upper surface of the wing made from composite materials. The control system of each actuator uses three control loops (current, speed and position) characterised by five control gains. To tune the control gains, the Particle Swarm Optimisation (PSO) method is used. The application of the PSO method supposed the development of a MATLAB/Simulink® software model for the controlled actuator, which worked together with a software sub-routine implementing the PSO algorithm to find the best values for the five control gains that minimise the cost function. Once the best values of the control gains are established, the software model of the controlled actuator is numerically simulated in order to evaluate the quality of the obtained control system. Finally, the designed control system is experimentally validated in bench tests and wind-tunnel tests for all four miniature actuators integrated in the morphing wing experimental model. The wind-tunnel testing treats the system as a whole and includes, besides the evaluation of the controlled actuation system, the testing of the integrated morphing wing experimental model and the evaluation of the aerodynamic benefits brought by the morphing technology on this project. From this last perspective, the airflow on the morphing upper surface of the experimental model is monitored by using various techniques based on pressure data collection with Kulite pressure sensors or on infrared thermography camera visualisations.

scholarly journals Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor

Nanomaterials ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 306 ◽  
Author(s):  
Paulina Listewnik ◽  
Marzena Hirsch ◽  
Przemysław Struk ◽  
Matthieu Weber ◽  
Mikhael Bechelany ◽  
...  
Keyword(s):  
Refractive Index ◽  
Optical Fiber ◽  
Fiber Optic ◽  
Single Mode ◽  
Atomic Layer ◽  
Fiber Optic Sensor ◽  
Refractive Index Sensor ◽  
Layer Deposition ◽  
Fabry Perot

We report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C. The modified fiber-optic microsphere was examined using scanning electron microscopy and Raman spectroscopy. Theoretical modeling has been carried out to assess the structure performance, and the performed experimental measurements carried out confirmed the enhanced sensing abilities when the microsphere was coated with a ZnO layer. The fabricated refractive index sensor was operating in a reflective mode of a Fabry–Pérot configuration, using a low coherent measurement system. The application of the ALD ZnO coating enabled for a better measurement of the refractive index of samples in the range of the refractive index allowed by the optical fiber. The proof-of-concept results presented in this work open prospects for the sensing community and will promote the use of fiber-optic sensing technologies.

Raman distributed temperature fiber-optic sensor based on single-mode fiber

2015 ◽  
Author(s):  
Sun Woo Kim ◽  
Min Seong Seo ◽  
Jung Min Hwang ◽  
Bong-Wan Lee ◽  
Min Yong Jeon
Keyword(s):  
Fiber Optic ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fiber Optic Sensor ◽  
Optic Sensor

The Application of Fiber Optic Sensor to the Study of Engineering Structure

2006 ◽  
Vol 326-328 ◽  
pp. 1351-1354
Author(s):  
Qi Rong Zhu ◽  
Ru Hua Fang ◽  
Guo Biao Yang ◽  
Wei Ming Zeng
Keyword(s):  
Fiber Optic ◽  
Experimental Testing ◽  
Smart Structure ◽  
Fiber Optic Sensor ◽  
Measuring System ◽  
Vibration Measurement ◽  
Technical Equipment ◽  
Electronic Measuring ◽  
Engineering Structure ◽  
Optic Sensor

The fiber optic sensor measuring system based on the Mech-Zehnder interferometry is developed in the paper. The system can be used for the strain and vibration measurement of engineering structure, and has the advantages: convenient adjusting, stable performance and strong ability of anti-interference, etc. Therefore the fiber optic sensor has been widely used in the engineering field. First the system is introduced into measuring the frequency and amplitude of the vibration subjected to force of the FRP-concrete beam. The fiber optic sensor measuring system and the electronic measuring system are synchronous used for the measurement. The analysis results of fiber optic sensor measurement approximate to the results of electronic strain gauge. Then the system is introduced into experimental stress analysis on the gas pipe, good results is obtained too. The paper provides new technical equipment for the experimental testing of various engineering structure using fiber optic sensor, also establishes the technical foundation of the research of smart structure.

Sign in / Sign up

Export Citation Format

Share Document