Optimizing multijunction photonic power converter design with measured radiative efficiency

2021 ◽  
Author(s):  
Daixi Xia ◽  
Matthew M. Wilkins ◽  
Jacob J. Krich
Keyword(s):  
Power Converter ◽  
Radiative Efficiency ◽  
Converter Design

scholarly journals Power converter design options for the 12 kVdc bus system

2017 ◽  
Author(s):  
A.L. Gattozzi ◽  
S.M. Strank ◽  
S.P. Pish ◽  
J.D. Herbst ◽  
R.E. Hebner ◽  
...  
Keyword(s):  
Power Converter ◽  
Converter Design ◽  
Design Options ◽  
Bus System

Study on the Impact of Layer Number on Stray Inductance of Busbar

2013 ◽  
Vol 321-324 ◽  
pp. 1439-1442
Author(s):  
Yi Feng Zhu ◽  
Zheng Zheng ◽  
Hai Jun Tao
Keyword(s):  
High Power ◽  
Power Converter ◽  
Main Concern ◽  
Power Devices ◽  
Layer Number ◽  
Converter Design ◽  
Partial Element Equivalent Circuit ◽  
The Impact ◽  
Partial Element

In high power converter design, low-inductance busbar connecting DC capacitors and power devices is main concern to improve the quality of the whole power electronics system. This paper analyzes the impact of layer-number on the stray inductance of busbar taking a subway traction converter as example. The method of partial element equivalent circuit and the Q3D software were used to extract the stray inductance. The simulation and experimental results show that the stray inductance of three-layer busbar is lower than two-layer busbar with other same conditions.

scholarly journals Two-Stage Optimization Method for Efficient Power Converter Design Including Light Load Operation

2012 ◽  
Vol 27 (3) ◽  
pp. 1327-1337 ◽  
Author(s):  
Ruiyang Yu ◽  
Bryan Man Hay Pong ◽  
Bingo Wing-Kuen Ling ◽  
J. Lam
Keyword(s):  
Optimization Method ◽  
Power Converter ◽  
Two Stage ◽  
Light Load ◽  
Converter Design ◽  
Efficient Power

scholarly journals Kontrol Kecepatan Motor Brushless DC Menggunakan Double Boost Converter Berbasis PI

CYCLOTRON ◽  
2020 ◽  
Vol 3 (1) ◽  
Author(s):  
Gita Arya Pratama ◽  
M. Krisna Ramadhani Ananta ◽  
Rio Winas Setia Budi ◽  
Belly Yan Dewantara ◽  
Iradiratu K
Keyword(s):  
Output Voltage ◽  
Power Converter ◽  
Pi Controller ◽  
Boost Converter ◽  
Bldc Motor ◽  
Brushless Dc ◽  
Dc Power ◽  
Output Load ◽  
Motor Load ◽  
Converter Design

Abstrak— Paper ini menampilkan desain double boost converter yang mempunyai kemampuan menggandakan tegangan dua kali lipat berturut  turut beban DC yang menghasilkan tegangan output tambahan atau cadangan suplai pada beban. Pada umumnya double boost converter ini adalah konverter daya DC to Dc meningkatkan tegangan dari input (pasokan) ke output (beban) di desain menunjukkan bahwa dengan inputan sumber AC yang di searahkan terlebih dulu dengan converter penyearah berfungsi untuk mengatur kecepatan motor BLDC. Untuk pengontrolan pada beban motor menggunakan PI controller ( Proportional Integrator) dimana  parameter PI controller diperoleh dari trial eror. PI controller juga berfungsi memperbaiki gelombang keluaran dan kecepatan motor BLDC. Kata kunci : Motor BLDC, Double Boost Converter, PI controller. Abstract— This paper features a double boost converter design that has the ability to double the successive voltage in a DC load which results in an additional output voltage or supply reserve at load. In general, this double boost converter is a DC to Dc power converter increasing the voltage from input (supply) to output (load) in the design shows that the input AC source is aligned first with the rectifier converter to regulate the speed of the BLDC motor. To control the motor load using a PI controller (Proportional Integrator) where the PI controller parameter is obtained from the trial error. The PI controller also functions to improve the wave output and speed of the BLDC motor.

scholarly journals Multi-Variable Thermal Modeling of Power Devices Considering Mutual Coupling

2019 ◽  
Vol 9 (16) ◽  
pp. 3240
Author(s):  
Wei ◽  
Cheng ◽  
Lu ◽  
Siwakoti ◽  
Zhang
Keyword(s):  
Working Conditions ◽  
Thermal Effects ◽  
Mutual Coupling ◽  
Thermal Modeling ◽  
Power Converter ◽  
Thermal Coupling ◽  
Power Devices ◽  
Cooling Process ◽  
Converter Design ◽  
Design Power

In relation to power converter design, power density is increasing while the form factor isdecreasing. This trend generally reduces the rate of the cooling process, which increases the mutualthermal coupling among the surrounding power components. Most of the traditional modelsusually ignore the mutual effects or just focus on the conduction coupling. To deal with these factors,the thermal modeling for a boost converter system has been built to compare the junctiontemperatures (Tj) and the increments under different working conditions in order to consider theconduction coupling. A multi-variable thermal resistances model is proposed in this paper toincorporate the convection thermal coupling into the mutual thermal effects. The couplingresistances, MOSFET to the diode[...]

Sign in / Sign up

Export Citation Format

Share Document