Comparison between laser thermal effects and ablation effects with ultrashort pulses laser on GO SiFe electrical steel

2019 ◽  
Author(s):  
Julien Dupuy ◽  
Olivier Maloberti ◽  
Nesser Manar ◽  
Yves Hernandez
Keyword(s):  
Thermal Effects ◽  
Electrical Steel ◽  
Ultrashort Pulses

Thermal Considerations in Lens Regulator Systems

1970 ◽  
Vol 28 ◽  
pp. 358-359
Author(s):  
K.C. Newton
Keyword(s):  
Electron Microscope ◽  
Thermal Effects ◽  
Environmental Control ◽  
Reference Networks ◽  
Better Than

Thermal effects in lens regulator systems have become a major problem with the extension of electron microscope resolution capabilities below 5 Angstrom units. Larger columns with immersion lenses and increased accelerating potentials have made solutions more difficult by increasing the power being handled. Environmental control, component choice, and wiring design provide answers, however. Figure 1 indicates with broken lines where thermal problems develop in regulator systemsExtensive environmental control is required in the sampling and reference networks. In each case, stability better than I ppm/min. is required. Components with thermal coefficients satisfactory for these applications without environmental control are either not available or priced prohibitively.

Direct measurement of electron-diffraction-pattern intensities using an energy loss spectrometer

1989 ◽  
Vol 47 ◽  
pp. 668-669
Author(s):  
A. G. Jackson ◽  
M. Rowe
Keyword(s):  
Thermal Effects ◽  
Dynamic Range ◽  
Scattering Amplitude ◽  
Dynamical Theory ◽  
Site Symmetry ◽  
Proof Of Concept ◽  
Parallel Acquisition ◽  
Kinematic Approximation ◽  
Speed Up ◽  
Structure Calculations

Diffraction intensities from intermetallic compounds are, in the kinematic approximation, proportional to the scattering amplitude from the element doing the scattering. More detailed calculations have shown that site symmetry and occupation by various atom species also affects the intensity in a diffracted beam. [1] Hence, by measuring the intensities of beams, or their ratios, the occupancy can be estimated. Measurement of the intensity values also allows structure calculations to be made to determine the spatial distribution of the potentials doing the scattering. Thermal effects are also present as a background contribution. Inelastic effects such as loss or absorption/excitation complicate the intensity behavior, and dynamical theory is required to estimate the intensity value.The dynamic range of currents in diffracted beams can be 104or 105:1. Hence, detection of such information requires a means for collecting the intensity over a signal-to-noise range beyond that obtainable with a single film plate, which has a S/N of about 103:1. Although such a collection system is not available currently, a simple system consisting of instrumentation on an existing STEM can be used as a proof of concept which has a S/N of about 255:1, limited by the 8 bit pixel attributes used in the electronics. Use of 24 bit pixel attributes would easily allowthe desired noise range to be attained in the processing instrumentation. The S/N of the scintillator used by the photoelectron sensor is about 106 to 1, well beyond the S/N goal. The trade-off that must be made is the time for acquiring the signal, since the pattern can be obtained in seconds using film plates, compared to 10 to 20 minutes for a pattern to be acquired using the digital scan. Parallel acquisition would, of course, speed up this process immensely.

Enhancement of RH Refractory Performance for Electrical Steel Processing

2019 ◽  
Author(s):  
S. Bharati ◽  
B. Patil ◽  
H. Vishwanath ◽  
P. Hittalamani ◽  
S. Joshi
Keyword(s):  
Electrical Steel ◽  
Steel Processing

Examination of Measurement Method for Magnetostriction of Electrical Steel Sheet with Lock-in Amplifier

2012 ◽  
Vol 132 (11) ◽  
pp. 1033-1038
Author(s):  
Yuichiro Kai ◽  
Yuji Tsuchida ◽  
Takashi Todaka ◽  
Masato Enokizono
Keyword(s):  
Measurement Method ◽  
Steel Sheet ◽  
Electrical Steel ◽  
Lock In ◽  
Electrical Steel Sheet

Measuring Iron Loss of the Electrical Steel Sheets with Different Grades under Compressive Stress Normal to the Surface

2019 ◽  
Vol 139 (4) ◽  
pp. 190-196
Author(s):  
Shinya Urata ◽  
Yoshitaka Maeda ◽  
Hideo Nakai ◽  
Yuuya Takeuchi ◽  
Kyyoul Yun ◽  
...  
Keyword(s):  
Compressive Stress ◽  
Electrical Steel ◽  
Iron Loss ◽  
Steel Sheets ◽  
Electrical Steel Sheets
Sign in / Sign up

Export Citation Format

Share Document