Enhancement of RH Refractory Performance for Electrical Steel Processing

2019 ◽  
Author(s):  
S. Bharati ◽  
B. Patil ◽  
H. Vishwanath ◽  
P. Hittalamani ◽  
S. Joshi
Keyword(s):  
Electrical Steel ◽  
Steel Processing

Study on Influence of Microstructure and Thermal Treatment on Magnetic Losses from Non-Oriented Silicon Electrical Steel

2017 ◽  
Vol 15 (13) ◽  
pp. 12-17
Author(s):  
Elena Valentina Stoian ◽  
Maria Cristiana Enescu ◽  
Vasile Bratu ◽  
Carmen Otilia Rusanescu ◽  
Florina Violeta Anghelina
Keyword(s):  
Magnetic Properties ◽  
Electrical Steel ◽  
Aging Treatment ◽  
Magnetic Characteristics ◽  
Magnetic Losses ◽  
Current Frequency ◽  
Steel Sheets ◽  
Wide Range ◽  
Steel Processing ◽  
Hot Rolled

AbstractNon/oriented electrical sheets are sheets tailored to produce specific properties and are produced from Fe-Si or Fe-Si-Al alloys. Non-oriented electrical steel sheets are incorporated into a wide range of equipment, from the simplest domestic appliances to hybrid and pure electric vehicles. In studying about the magnetic, there have a lot of method can be used for the different experiment requirement such as measuring magnetic flux, nominal loss and other objectives.During electrical steel processing, there are usually small variations in both chemical composition and thickness in the hot-rolled material that may lead to different magnetic properties for the same steel grade. Therefore, it is of great importance to know the effects of such variations on the final microstructure and magnetic properties of these steels. The purpose of this work was to study microstructural changes of the bands investigated during processing occurring siliceous strips with non-oriented grains. The second aim was to study the influence of grain size on the total magnetic losses at 1.0 T and 1.5 T. Materials 10 rolls intended to be processed into quality electrical steel M400-50A (according to EN 100027-1) were analyzed with metallographic microscope Neophet 32 and the magnetic characteristics was made with Epstein frame according IEC 6040/4-2, with an exiting current frequency of 50Hz at 1.5T and 1.0T induction after aging treatment of 225°C for 24 hours. Sample for light microscopy observation were prepared by polishing and etching in 5% Nital.

Examination of Measurement Method for Magnetostriction of Electrical Steel Sheet with Lock-in Amplifier

2012 ◽  
Vol 132 (11) ◽  
pp. 1033-1038
Author(s):  
Yuichiro Kai ◽  
Yuji Tsuchida ◽  
Takashi Todaka ◽  
Masato Enokizono
Keyword(s):  
Measurement Method ◽  
Steel Sheet ◽  
Electrical Steel ◽  
Lock In ◽  
Electrical Steel Sheet

Measuring Iron Loss of the Electrical Steel Sheets with Different Grades under Compressive Stress Normal to the Surface

2019 ◽  
Vol 139 (4) ◽  
pp. 190-196
Author(s):  
Shinya Urata ◽  
Yoshitaka Maeda ◽  
Hideo Nakai ◽  
Yuuya Takeuchi ◽  
Kyyoul Yun ◽  
...  
Keyword(s):  
Compressive Stress ◽  
Electrical Steel ◽  
Iron Loss ◽  
Steel Sheets ◽  
Electrical Steel Sheets

ARMCO TRAN-COR ELECTRICAL STEEL GRADE H-0

Alloy Digest ◽  
1990 ◽  
Vol 39 (9) ◽  
Keyword(s):  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Grain Orientation ◽  
Electrical Steel ◽  
Core Loss ◽  
Heat Treating ◽  
Steel Grade ◽  
Advanced Materials ◽  
Electrical Steels

Abstract Armco Tran-Cor H-0 Electrical Steel, available in coils 0.009 (0.23 mm) thickness, offers an outstanding degree of grain orientation with resultant far lower core loss than possible with conventional grain-oriented electrical steels. It is used for transformer cores. This datasheet provides information on physical properties, hardness, elasticity, and tensile properties. It also includes information on heat treating and surface treatment. Filing Code: Fe-92. Producer or source: Armco Advanced Materials Corporation.

Sign in / Sign up

Export Citation Format

Share Document