Three-dimensional printing and deformation behavior of low-density target structures by two-photon polymerization

2017 ◽  
Author(s):  
John H. Campbell ◽  
Nicole Nicole ◽  
Ori Stein ◽  
Ying Liu ◽  
Yongfeng Lu ◽  
...  
Keyword(s):  
Deformation Behavior ◽  
Three Dimensional ◽  
Low Density ◽  
Three Dimensional Printing ◽  
Two Photon ◽  
Dimensional Printing ◽  
Two Photon Polymerization

scholarly journals Alleviating Distortion and Improving the Young’s Modulus in Two-Photon Polymerization Fabrications

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 615 ◽  
Author(s):  
Chow-Shing Shin ◽  
Tzu-Jui Li ◽  
Chih-Lang Lin
Keyword(s):  
Young’S Modulus ◽  
Structural Integrity ◽  
Young's Modulus ◽  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Two Photon ◽  
Laser Focus ◽  
Micro Cantilever ◽  
Micro Structures ◽  
Two Photon Polymerization

Two-photon polymerization enables the extremely high resolution three-dimensional printing of micro-structures. To know the mechanical properties, and better still, to be able to adjust them is of paramount importance to ensuring the proper structural integrity of the printed products. In this work, the Young’s modulus is measured on two-photon polymerized micro-cantilever bars. Optimizing the scanning trajectory of the laser focus points is important in alleviating distortion of the printed bars. By increasing the laser power and decreasing the inter-voxel distances we can double the Young’s modulus. Post-curing with ultraviolet light can approximately quadruple the Young’s modulus. However, the resulting modulus is still only about 0.3% of that of the bulk polymerized material.

Cleavable Unimolecular Photoinitiators Based on Oxime‐Ester Chemistry for Two‐Photon Three‐Dimensional Printing

ChemPhotoChem ◽  
2019 ◽  
Vol 3 (11) ◽  
pp. 1090-1094 ◽  
Author(s):  
Wanwan Qiu ◽  
Peng Hu ◽  
Junzhe Zhu ◽  
Ren Liu ◽  
Zhiquan Li ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Two Photon ◽  
Dimensional Printing

A novel fast disintegrating tablet fabricated by three‐dimensional printing

2009 ◽  
Vol 00 (00) ◽  
pp. 090730035508060-7
Author(s):  
Deng-Guang Yu ◽  
Chris Branford-White ◽  
Yi-Cheng Yang ◽  
Li-Min Zhu ◽  
Edward William Welbeck ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Fast Disintegrating Tablet ◽  
Dimensional Printing

Central ossifying fibroma of mandible

2020 ◽  
Vol 13 (12) ◽  
pp. e239286
Author(s):  
Kumar Nilesh ◽  
Prashant Punde ◽  
Nitin Shivajirao Patil ◽  
Amol Gautam
Keyword(s):  
Fibrous Tissue ◽  
Three Dimensional ◽  
Facial Asymmetry ◽  
Ossifying Fibroma ◽  
Mandible Reconstruction ◽  
Three Dimensional Printing ◽  
Osseous Lesion ◽  
Large Size ◽  
Dimensional Printing

Ossifying fibroma (OF) is a rare, benign, fibro-osseous lesion of the jawbone characterised by replacement of the normal bone with fibrous tissue. The fibrous tissue shows varying amount of calcified structures resembling bone and/or cementum. The central variant of OF is rare, and shows predilection for mandible among the jawbone. Although it is classified as fibro-osseous lesion, it clinically behaves as a benign tumour and can grow to large size, causing bony swelling and facial asymmetry. This paper reports a case of large central OF of mandible in a 40-year-old male patient. The lesion was treated by segmental resection of mandible. Reconstruction of the surgical defect was done using avascular fibula bone graft. Role of three-dimensional printing of jaw and its benefits in surgical planning and reconstruction are also highlighted.

scholarly journals Three-Dimensional Printing in Orthopedics: from the Basics to Surgical Applications

2021 ◽  
Author(s):  
Leandro Ejnisman ◽  
Bruno Gobbato ◽  
Andre Ferrari de França Camargo ◽  
Eduardo Zancul
Keyword(s):  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Dimensional Printing
Sign in / Sign up

Export Citation Format

Share Document