Investigation of binary coating material mixtures using grazing incidence EUV-reflectometry

2014 ◽  
Author(s):  
I. Balasa ◽  
X. Neiers ◽  
M. Mende ◽  
L. Jensen ◽  
D. Ristau
Keyword(s):  
Grazing Incidence ◽  
Coating Material

convergent-beam diffraction from surfaces

1987 ◽  
Vol 45 ◽  
pp. 30-33
Author(s):  
J. A. Eades ◽  
A. E. Smith ◽  
D. F. Lynch
Keyword(s):  
Reciprocal Lattice ◽  
Three Dimensional ◽  
Grazing Incidence ◽  
Three Dimensions ◽  
Plane Figure ◽  
Transmission Electron ◽  
Convergent Beam ◽  
Beam Patterns ◽  
Beam Diffraction

It is quite simple (in the transmission electron microscope) to obtain convergent-beam patterns from the surface of a bulk crystal. The beam is focussed onto the surface at near grazing incidence (figure 1) and if the surface is flat the appropriate pattern is obtained in the diffraction plane (figure 2). Such patterns are potentially valuable for the characterization of surfaces just as normal convergent-beam patterns are valuable for the characterization of crystals.There are, however, several important ways in which reflection diffraction from surfaces differs from the more familiar electron diffraction in transmission.GeometryIn reflection diffraction, because of the surface, it is not possible to describe the specimen as periodic in three dimensions, nor is it possible to associate diffraction with a conventional three-dimensional reciprocal lattice.

New Structure of CTAB Templated Silica Films as revealed by GISAXS coupled to HRTEM

2000 ◽  
Vol 628 ◽  
Author(s):  
Sophie Besson ◽  
Catherine Jacquiod ◽  
Thierry Gacoin ◽  
André Naudon ◽  
Christian Ricolleau ◽  
...  
Keyword(s):  
Cetyltrimethylammonium Bromide ◽  
Grazing Incidence ◽  
Hexagonal Structure ◽  
X Ray Diffraction ◽  
Electronic Microscopy ◽  
Silica Films ◽  
X Ray ◽  
X Ray Scattering ◽  
Hexagonal Arrangement ◽  
Spherical Micelles

ABSTRACTA microstructural study on surfactant templated silica films is performed by coupling traditional X-Ray Diffraction (XRD) and Transmission Electronic Microscopy (TEM) to Grazing Incidence Small Angle X-Ray Scattering (GISAXS). By this method it is shown that spin-coating of silicate solutions with cationic surfactant cetyltrimethylammonium bromide (CTAB) as a templating agent provides 3D hexagonal structure (space group P63/mmc) that is no longer compatible with the often described hexagonal arrangement of tubular micelles but rather with an hexagonal arrangement of spherical micelles. The extent of the hexagonal ordering and the texture can be optimized in films by varying the composition of the solution.

Effects of Aging on the Morphology of Rubber-Brass Interfacial Layer

2011 ◽  
Vol 39 (1) ◽  
pp. 20-43 ◽  
Author(s):  
A. Ashirgade ◽  
P. B. Harakuni ◽  
W. J. Vanooij
Keyword(s):  
Chemical Composition ◽  
Interfacial Layer ◽  
Secondary Ion Mass Spectrometry ◽  
Morphological Changes ◽  
Grazing Incidence ◽  
Complex Nature ◽  
Rubber Compound ◽  
Tire Cord ◽  
Morphological Transformation ◽  
Adhesion Promoter

Abstract Adhesion between rubber compound and brass-plated steel tire cord is crucial in governing the overall performance of tires. The rubber-brass interfacial adhesion is influenced by the chemical composition and thickness of the interfacial layer. It has been shown that the interfacial layer consists mainly of sulfides and oxides of copper and zinc. This paper discusses the effect of changes in the chemical composition and the structure of the interfacial layers due to addition of adhesion promoter resins. Grazing incidence x-ray diffraction (GIXRD) experiments were run on sulfidized polished brass coupons previously bonded to five experimental rubber compounds. It was confirmed that heat and humidity conditions lead to physical and chemical changes of the rubber-steel tire cord interfacial layer, closely related to the degree of rubber-brass adhesion. Morphological transformation of the interfacial layer led to loss of adhesion after aging. The adhesion promoter resins inhibit unfavorable morphological changes in the interfacial layer, thus stabilizing it during aging and prolonging failure. Tire cord adhesion tests illustrated that the one-component resins improved adhesion after aging using a rubber compound with lower cobalt loading. Based on the acquired diffraction profiles, these resins were also found to impede crystallization of the sulfide layer after aging, leading to improved adhesion. Secondary ion mass spectrometry depth profiles and scanning electron microscopy micrographs strongly corroborated the findings from GIXRD. This interfacial analysis adds valuable information to our understanding of the complex nature of the rubber-brass bonding mechanism.

X-Ray Fluorescence Spectrometer with Geometry of Grazing Incidence X-ray Radiation

2012 ◽  
Vol 1 (2) ◽  
pp. 78-82
Author(s):  
N.M. Novikovskii ◽  
◽  
V.M. Raznomazov ◽  
V.O. Ponomarenko ◽  
D.A. Sarychev ◽  
...  
Keyword(s):  
Grazing Incidence ◽  
X Ray ◽  
Fluorescence Spectrometer

Quantifying Multiple Crystallite Orientations and Crystal Heterogeneities in Complex Thin Film Materials

2019 ◽  
Author(s):  
Jonathan Ogle ◽  
Daniel Powell ◽  
Eric Amerling ◽  
Detlef Matthias Smilgies ◽  
Luisa Whittaker-Brooks
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Structural Design ◽  
Grazing Incidence ◽  
Crystallite Orientation ◽  
Miller Index ◽  
X Ray ◽  
X Ray Scattering ◽  
Orientation Distributions ◽  
Orientation Information

<p>Thin film materials have become increasingly complex in morphological and structural design. When characterizing the structure of these films, a crucial field of study is the role that crystallite orientation plays in giving rise to unique electronic properties. It is therefore important to have a comparative tool for understanding differences in crystallite orientation within a thin film, and also the ability to compare the structural orientation between different thin films. Herein, we designed a new method dubbed the mosaicity factor (MF) to quantify crystallite orientation in thin films using grazing incidence wide-angle X-ray scattering (GIWAXS) patterns. This method for quantifying the orientation of thin films overcomes many limitations inherent in previous approaches such as noise sensitivity, the ability to compare orientation distributions along different axes, and the ability to quantify multiple crystallite orientations observed within the same Miller index. Following the presentation of MF, we proceed to discussing case studies to show the efficacy and range of application available for the use of MF. These studies show how using the MF approach yields quantitative orientation information for various materials assembled on a substrate.<b></b></p>

Sign in / Sign up

Export Citation Format

Share Document