Exact derivation of the tensile strain and strain rate equations for a rotating capstan fiber tester

1993 ◽  
Author(s):  
James J. Carr ◽  
Donald R. Dreyer
Keyword(s):  
Strain Rate ◽  
Tensile Strain ◽  
Rate Equations ◽  
Strain And Strain Rate ◽  
Exact Derivation

The effects of strain and strain rate on residual microstructures in copper

1986 ◽  
Vol 44 ◽  
pp. 420-421
Author(s):  
M. F. Stevens ◽  
P. S. Follansbee
Keyword(s):  
Strain Rate ◽  
Applied Stress ◽  
Threshold Stress ◽  
Rate Sensitivity ◽  
Viscous Drag ◽  
Strain Rates ◽  
Strain And Strain Rate ◽  
Threshold Strength ◽  
Mechanism Transition ◽  
Intrinsic Strength

The strain rate sensitivity of a variety of materials is known to increase rapidly at strain rates exceeding ∼103 sec-1. This transition has most often in the past been attributed to a transition from thermally activated guide to viscous drag control. An important condition for imposition of dislocation drag effects is that the applied stress, σ, must be on the order of or greater than the threshold stress, which is the flow stress at OK. From Fig. 1, it can be seen for OFE Cu that the ratio of the applied stress to threshold stress remains constant even at strain rates as high as 104 sec-1 suggesting that there is not a mechanism transition but that the intrinsic strength is increasing, since the threshold strength is a mechanical measure of intrinsic strength. These measurements were made at constant strain levels of 0.2, wnich is not a guarantee of constant microstructure. The increase in threshold stress at higher strain rates is a strong indication that the microstructural evolution is a function of strain rate and that the dependence becomes stronger at high strain rates.

scholarly journals Application of the Strain Compensation Model and Processing Maps for Description of Hot Deformation Behavior of Metastable β Titanium Alloy

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2021
Author(s):  
Oleksandr Lypchanskyi ◽  
Tomasz Śleboda ◽  
Aneta Łukaszek-Sołek ◽  
Krystian Zyguła ◽  
Marek Wojtaszek
Keyword(s):  
Titanium Alloy ◽  
Strain Rate ◽  
Flow Behavior ◽  
Microstructural Analysis ◽  
Calculated Data ◽  
Processing Temperature ◽  
Processing Maps ◽  
Compression Tests ◽  
Strain And Strain Rate ◽  
Average Absolute Relative Error

The flow behavior of metastable β titanium alloy was investigated basing on isothermal hot compression tests performed on Gleeble 3800 thermomechanical simulator at near and above β transus temperatures. The flow stress curves were obtained for deformation temperature range of 800–1100 °C and strain rate range of 0.01–100 s−1. The strain compensated constitutive model was developed using the Arrhenius-type equation. The high correlation coefficient (R) as well as low average absolute relative error (AARE) between the experimental and the calculated data confirmed a high accuracy of the developed model. The dynamic material modeling in combination with the Prasad stability criterion made it possible to generate processing maps for the investigated processing temperature, strain and strain rate ranges. The high material flow stability under investigated deformation conditions was revealed. The microstructural analysis provided additional information regarding the flow behavior and predominant deformation mechanism. It was found that dynamic recovery (DRV) was the main mechanism operating during the deformation of the investigated β titanium alloy.

A Study of Strain and Strain-Rate Dependent Properties of a Superplastic Zn-Al Alloy Under Biaxial Stresses

1982 ◽  
Vol 104 (1) ◽  
pp. 41-46
Author(s):  
T. C. Hsu ◽  
I. M. Bidhendi
Keyword(s):  
Strain Rate ◽  
Stress Ratio ◽  
Local Stress ◽  
Biaxial Stress ◽  
Al Alloy ◽  
Local Geometry ◽  
Forming Process ◽  
Rate Dependent ◽  
Strain And Strain Rate ◽  
Liquid Behavior

A superplastic Zn-Al alloy in sheet form is formed into a bulge over a circular hole by pneumatic pressure. The geometry, the stress, the strain, and the strain-rate are determined at various points covering the whole specimen and at various stages of the forming process. The complicated shape, and its complicated changes, are represented by introducing an index for the local geometry, called “prolateness,” which is also related to the local stress ratio in a simple way. The biaxial stress is analyzed into a strain-proportional and a strain-rate-proportional component, which represent, respectively, the quasi-solid and the quasi-liquid behavior of the superplastic material.

Effect of Strain Rate on Nb(C,N) Precipitation in Micro Alloy Steel Slab

2012 ◽  
Vol 535-537 ◽  
pp. 633-638 ◽  
Author(s):  
Zheng Hai Zhu ◽  
Sheng Tao Qiu
Keyword(s):  
Continuous Casting ◽  
Strain Rate ◽  
Alloy Steel ◽  
Casting Speed ◽  
Casting Process ◽  
Continuous Casting Process ◽  
Precipitation Model ◽  
Strain And Strain Rate ◽  
Steel Slab

It was analyzed by strain-induced precipitation model that Nb(C,N) precipitation in micro alloy steel slab was effected by strain rate during continuous casting process. The results are as follows: The changing of casting speed could effect the time for 5%precipitation of Nb(C,N), which was decreasing with increasing casting speed at certain temperature and strain rate. Slab strain and strain rate were too small in bending zone and leveling zone. The effect of slab strain rate on Nb(C,N) precipitation could be ignore when Nb(C,N) precipitation in continuous casting process was studied.

Numerical Analysis of Plane-Strain Tension Test for Rate-Dependent Solids

1992 ◽  
Vol 59 (3) ◽  
pp. 485-490 ◽  
Author(s):  
P. Tugˇcu
Keyword(s):  
Numerical Analysis ◽  
Strain Rate ◽  
Plane Strain ◽  
Rate Sensitivity ◽  
Tension Test ◽  
Engineering Strain ◽  
Plane Strain Tension ◽  
Rate Dependent ◽  
Strain And Strain Rate ◽  
Strain Rate Hardening

The plane-strain tension test is analyzed numerically for a material with strain and strain-rate hardening characteristics. The effect of the prescribed rate of straining is investigated for an additive logarithmic description of the material strain-rate sensitivity. The dependency to the imposed strain rate so introduced is shown to have a significant effect on several features of the load-elongation curve such as the attainment of the load maximum, the onset of localization, and the overall engineering strain.

Sign in / Sign up

Export Citation Format

Share Document