Influences of tensile strain and strain rate on the electron work function of metals and alloys

2006 ◽  
Vol 54 (5) ◽  
pp. 921-924 ◽  
Author(s):  
W. Li ◽  
M. Cai ◽  
Y. Wang ◽  
S. Yu
Keyword(s):  
Strain Rate ◽  
Work Function ◽  
Tensile Strain ◽  
Electron Work Function ◽  
Metals And Alloys ◽  
Strain And Strain Rate

The effects of strain and strain rate on residual microstructures in copper

1986 ◽  
Vol 44 ◽  
pp. 420-421
Author(s):  
M. F. Stevens ◽  
P. S. Follansbee
Keyword(s):  
Strain Rate ◽  
Applied Stress ◽  
Threshold Stress ◽  
Rate Sensitivity ◽  
Viscous Drag ◽  
Strain Rates ◽  
Strain And Strain Rate ◽  
Threshold Strength ◽  
Mechanism Transition ◽  
Intrinsic Strength

The strain rate sensitivity of a variety of materials is known to increase rapidly at strain rates exceeding ∼103 sec-1. This transition has most often in the past been attributed to a transition from thermally activated guide to viscous drag control. An important condition for imposition of dislocation drag effects is that the applied stress, σ, must be on the order of or greater than the threshold stress, which is the flow stress at OK. From Fig. 1, it can be seen for OFE Cu that the ratio of the applied stress to threshold stress remains constant even at strain rates as high as 104 sec-1 suggesting that there is not a mechanism transition but that the intrinsic strength is increasing, since the threshold strength is a mechanical measure of intrinsic strength. These measurements were made at constant strain levels of 0.2, wnich is not a guarantee of constant microstructure. The increase in threshold stress at higher strain rates is a strong indication that the microstructural evolution is a function of strain rate and that the dependence becomes stronger at high strain rates.

scholarly journals Application of the Strain Compensation Model and Processing Maps for Description of Hot Deformation Behavior of Metastable β Titanium Alloy

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2021
Author(s):  
Oleksandr Lypchanskyi ◽  
Tomasz Śleboda ◽  
Aneta Łukaszek-Sołek ◽  
Krystian Zyguła ◽  
Marek Wojtaszek
Keyword(s):  
Titanium Alloy ◽  
Strain Rate ◽  
Flow Behavior ◽  
Microstructural Analysis ◽  
Calculated Data ◽  
Processing Temperature ◽  
Processing Maps ◽  
Compression Tests ◽  
Strain And Strain Rate ◽  
Average Absolute Relative Error

The flow behavior of metastable β titanium alloy was investigated basing on isothermal hot compression tests performed on Gleeble 3800 thermomechanical simulator at near and above β transus temperatures. The flow stress curves were obtained for deformation temperature range of 800–1100 °C and strain rate range of 0.01–100 s−1. The strain compensated constitutive model was developed using the Arrhenius-type equation. The high correlation coefficient (R) as well as low average absolute relative error (AARE) between the experimental and the calculated data confirmed a high accuracy of the developed model. The dynamic material modeling in combination with the Prasad stability criterion made it possible to generate processing maps for the investigated processing temperature, strain and strain rate ranges. The high material flow stability under investigated deformation conditions was revealed. The microstructural analysis provided additional information regarding the flow behavior and predominant deformation mechanism. It was found that dynamic recovery (DRV) was the main mechanism operating during the deformation of the investigated β titanium alloy.

Electron work function of Rb-Cs alloys

2006 ◽  
Vol 51 (12) ◽  
pp. 1627-1629
Author(s):  
B. B. Alchagirov ◽  
B. S. Karamurzov ◽  
T. A. Sizhazhev ◽  
T. M. Taova ◽  
R. Kh. Arkhestov
Keyword(s):  
Work Function ◽  
Electron Work Function

A Study of Strain and Strain-Rate Dependent Properties of a Superplastic Zn-Al Alloy Under Biaxial Stresses

1982 ◽  
Vol 104 (1) ◽  
pp. 41-46
Author(s):  
T. C. Hsu ◽  
I. M. Bidhendi
Keyword(s):  
Strain Rate ◽  
Stress Ratio ◽  
Local Stress ◽  
Biaxial Stress ◽  
Al Alloy ◽  
Local Geometry ◽  
Forming Process ◽  
Rate Dependent ◽  
Strain And Strain Rate ◽  
Liquid Behavior

A superplastic Zn-Al alloy in sheet form is formed into a bulge over a circular hole by pneumatic pressure. The geometry, the stress, the strain, and the strain-rate are determined at various points covering the whole specimen and at various stages of the forming process. The complicated shape, and its complicated changes, are represented by introducing an index for the local geometry, called “prolateness,” which is also related to the local stress ratio in a simple way. The biaxial stress is analyzed into a strain-proportional and a strain-rate-proportional component, which represent, respectively, the quasi-solid and the quasi-liquid behavior of the superplastic material.

Sign in / Sign up

Export Citation Format

Share Document