Dark current–voltage characteristics of vacuum deposited multilayer amorphous selenium-alloy detectors and the effect of x-ray irradiation

2019 ◽  
Vol 37 (6) ◽  
pp. 061501 ◽  
Author(s):  
Joel B. Frey ◽  
Kalaivani Sadasivam ◽  
George Belev ◽  
Habib Mani ◽  
Luc Laperriere ◽  
...  
Keyword(s):  
Dark Current ◽  
Amorphous Selenium ◽  
X Ray ◽  
Current Voltage ◽  
Current Voltage Characteristics

Study on Schottky Diode Characteristics Improving by X-Ray Irradiation

2013 ◽  
Vol 717 ◽  
pp. 113-116
Author(s):  
Sani Klinsanit ◽  
Itsara Srithanachai ◽  
Surada Ueamanapong ◽  
Sunya Khunkhao ◽  
Budsara Nararug ◽  
...  
Keyword(s):  
Leakage Current ◽  
Schottky Diode ◽  
Room Temperature ◽  
The Other ◽  
Low Power Consumption ◽  
Initial Value ◽  
X Ray ◽  
Forward Current ◽  
Current Voltage ◽  
Current Voltage Characteristics

The effect of soft X-ray irradiation to the Schottky diode properties was analyzed in this paper. The built-in voltage, leakage current, and work function of Schottky diode were investigated. The current-voltage characteristics of the Schottky diode are measured at room temperature. After irradiation at 70 keV for 55 seconds the forward current and leakage current are increase slightly. On the other hand, the built-in voltage is decrease from the initial value about 0.12 V. Consequently, this method can cause the Schottky diode has low power consumption. The results show that soft X-ray can improve the characteristics of Schottky diode.

scholarly journals Understanding Dark Current-Voltage Characteristics in Metal-Halide Perovskite Single Crystals

2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Elisabeth A. Duijnstee ◽  
Vincent M. Le Corre ◽  
Michael B. Johnston ◽  
L. Jan Anton Koster ◽  
Jongchul Lim ◽  
...  
Keyword(s):  
Single Crystals ◽  
Dark Current ◽  
Metal Halide ◽  
Metal Halide Perovskite ◽  
Current Voltage ◽  
Current Voltage Characteristics ◽  
Halide Perovskite

Morphology and I-V Characteristics of Electrochemically Deposited Zinc Oxide on Silicon

2021 ◽  
Vol 20 (3) ◽  
pp. 32-36
Author(s):  
Ahmad Bukhairi Md Rashid ◽  
Mastura Shafinaz Zainal Abidin ◽  
Shaharin Fadzli Abd Rahman ◽  
Amirjan Nawabjan
Keyword(s):  
Zinc Oxide ◽  
Electrochemical Deposition ◽  
Dark Current ◽  
Room Temperature ◽  
Volume Ratio ◽  
Deposition Process ◽  
X Ray ◽  
Current Voltage ◽  
Electrochemically Deposited ◽  
A Current

This paper reported on the electrochemical deposition of zinc oxide (ZnO) on p-silicon (p-Si) (100) substrate in the mixture of 0.1 M of zinc chloride (ZnCl2) and potassium chloride (KCl) electrolyte at a volume ratio of 1:1, 3:1 and 5:1 namely Sample A, B and C. The deposition process was done in room temperature with a current density of 10 mA/cm2 for 30 minutes. Prior to the experiment, all samples were treated by RCA cleaning steps. All samples were characterized using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). The results show that all samples have the same morphology of a flake-like structure with different Zn:O ratio that were 2.81, 2.35 and 2.49 for samples A, B and C. The current-voltage (I-V) characteristic graph was obtained by dark current measurement using Keithley SMU 2400 and the threshold voltage (Vth) values were determined at 2.21 V, 0.85 V and 1.22 V for sample A, B and C respectively which correspond with the Zn:O ratio where the highest value of Zn:O ratio can be found in sample A and the lowest in sample B. Based on these results, it shows that electrochemical deposition technique is capable of being used to deposit the flake-like structure ZnO on semiconductor material to form the p-n junction which behaves like a diode. The value of Vth seems to be depended on the ratio between Zn and O. Higher ratio of Zn and O will cause the higher value of intrinsic carrier concentration and built in potential which will increase the Vth value.

Temperature dependence of current-voltage characteristics in μc-Si:H and pm-Si:H PIN structures

2012 ◽  
Vol 1426 ◽  
pp. 365-370
Author(s):  
Francisco Temoltzi Avila ◽  
Andrey Kosarev ◽  
Ismael Cosme ◽  
Mario Moreno ◽  
P. Roca y Cabarrocas
Keyword(s):  
Temperature Dependence ◽  
Temperature Change ◽  
Ideality Factor ◽  
Dark Current ◽  
Series Resistance ◽  
Equivalent Circuit Model ◽  
Saturation Current ◽  
Current Voltage ◽  
Current Voltage Characteristics

ABSTRACTThe dark current-voltage characteristics of PIN structures are studied and analyzed for PV samples as for integral device without taking account the performance of the different elements typically used in equivalent circuit model such as diode n-factor, shunt and series resistances. The contribution of all these elements is very important in the development of devices because they determine the performance characteristics. In this work we have studied and compared the temperature dependence of current-voltage characteristics in μc-Si:H and pm-Si:H p-i-n structures having approximately the same efficiencies with emphasis on their different electronic characteristics such as shunt (Rsh) and series (Rs) resistance, ideality factor (n), and the saturation current (Is), which give us some ideas on role of these elements. In the pm-Si:H cell it was observed that the Rs increases with the increase of the temperature in contrast to the μc-Si:H structures, where the series resistance reduces with temperature change from T = 300 up to 480K. In both the pm-Si:H and μc-Si:H samples Rshreduces with temperature change from 300 up to 480 K. The ideality factor in the pm-Si:H structure shows an increase, and in μc-Si:H a reduction, when temperature increases. Saturation current in both cases increases with temperature as it was expected. From the saturation current it was obtained the build-in potential. Analysis behavior of both saturation current and n-factor with temperature shows that build-in potential increases with temperature in the pm-Si:H, but reduces in μc-Si:H structure.

ELECTRONIC STRUCTURE AND CONDUCTIVITY OF HYDROCARBON FILMS OBTAINED IN PLASMA DISCHARGES OF TOKAMAK T-10

1970 ◽  
Vol 61 (11) ◽  
Author(s):  
Galina A. Sokolina ◽  
Igor I. Arkhipov ◽  
Nikolay Yu. Svechnikov ◽  
Sergey A. Grashin
Keyword(s):  
Activation Energy ◽  
Electronic Structure ◽  
Temperature Dependence ◽  
Direct Current ◽  
Plasma Discharges ◽  
X Ray ◽  
Hydrocarbon Films ◽  
Direct Current Conductivity ◽  
Current Voltage ◽  
Current Voltage Characteristics

Amorphous hydrocarbon films on silicon substrates obtained in the chamber of tokamak T-10 with space-bounded deuterium plasma by carbon diaphragms were studied. Using the methods of spectrophotometry, ellipsometry, X-ray photoemission spectroscopy and X-ray excited Auger electron spectroscopy, it was established that the refraction and absorption coefficients of films, as well as the parameters of the electronic structure such as the magnitude of the band gap, the fraction of sp2-hybridized carbon and the chemical composition of impurities depend on the characteristics of the discharge in the tokamak. It is shown that the deposited films refer to high-resistance dielectrics, and they can be classified by optical properties as hard or soft amorphous hydrocarbon films, depending on the type of the plasma discharge (pulse working discharge or long-term low-energy cleaning discharge). Wherein, the conductivity of hard films is less than that of soft films, which corresponds to a smaller fraction of sp2-states of carbon in these films and to a higher value of the band gap. The current-voltage characteristics and the temperature dependence of the direct current conductivity of hard and soft films were measured. It was shown that in the temperature range of 293–550 K, the conductivity is determined by the hopping conductivity mechanism over localized states near the Fermi level and the boundaries of the allowed bands. The hopping conductivity mechanism is also indicated by the power law obtained at room temperature at alternating current with a value of a power exponent close to 0.8. The measurement of the current-voltage characteristics and the temperature dependence of the conductivity of hard and soft films showed a significant difference in the activation energy of conductivity and the conductivity at an elevated temperature. The established dependences of the direct current conductivity and the activation energy value of the films on the discharge parameters can be used as diagnostic benchmarks of different types of plasma discharges in a tokamak. Data on the electrical conductivity of the films are analyzed within the framework of the concept of the electronic structure of amorphous non-crystalline materials.  

Influence of Nickel Film Thicknesses on Dark Current-Voltage Characteristics of Silicon Solar Cells

2011 ◽  
Vol 694 ◽  
pp. 672-675
Author(s):  
Tao Li ◽  
Chun Lan Zhou ◽  
Zhen Gang Liu ◽  
Wen Jing Wang ◽  
Yang Song ◽  
...  
Keyword(s):  
Solar Cells ◽  
Dark Current ◽  
Nickel Silicide ◽  
Nickel Film ◽  
Silicon Solar Cells ◽  
Voltage Range ◽  
Voltage Curve ◽  
Current Voltage ◽  
Current Voltage Curve ◽  
Current Voltage Characteristics

In this paper, the dark current-voltage characteristics of p-n junction of silicon solar cells are analysed, with different nickel film thicknesses of 200nm, 400nm and 600nm. The formation of nickel silicide is obtained after the thermal annealing process for 1min, 5min and 10min. The dark current-voltage curves obtained by three kinds of annealing temperature as a function of time are achieved in experiment. The improvement of series resistance extracted from the dark current-voltage curve in the upper voltage range is observed. The influence of nickel film thicknesses on dark current-voltage characteristics of silicon solar cells is confirmed.

Dark current in multilayer stabilized amorphous selenium based photoconductive x-ray detectors

2012 ◽  
Vol 112 (1) ◽  
pp. 014502 ◽  
Author(s):  
Joel B. Frey ◽  
George Belev ◽  
Olivier Tousignant ◽  
Habib Mani ◽  
Luc Laperriere ◽  
...  
Keyword(s):  
Dark Current ◽  
Amorphous Selenium ◽  
X Ray
Sign in / Sign up

Export Citation Format

Share Document