Evaluation of the shapes of Auger- and secondary-electron line scans across interfaces with the logistic function

2006 ◽  
Vol 24 (4) ◽  
pp. 1024-1030 ◽  
Author(s):  
S. A. Wight ◽  
C. J. Powell
Keyword(s):  
Secondary Electron ◽  
Logistic Function ◽  
Electron Line

The Solidified Structure and Macrosegregation of Wedge-Shaped Titanium Castings Produced by Vertical Centrifugal Casting Process

2011 ◽  
Vol 317-319 ◽  
pp. 456-459 ◽  
Author(s):  
Shi Ping Wu ◽  
Qin Xu ◽  
Xiang Xue
Keyword(s):  
Rotational Speed ◽  
Secondary Electron ◽  
Centrifugal Casting ◽  
Casting Process ◽  
Alloy Element ◽  
Grain Sizes ◽  
Electron Line ◽  
Wedge Shape ◽  
Line Scanning ◽  
Scanning Electron

The present paper studied the as-cast structure and macrosegregation of the wedge-shaped castings produced vertical centrifugal casting process at different mould rotating speeds. The element distributions were determined by the secondary electron line scanning in the S-570SEM type scanning electron microscope (SEM) and the grain sizes of the castings were observed by the optical stereoscope. The research results show that the grain sizes increase with increasing of casting wall-thickness, but decrease with increasing of the mold rotational speed. The cooling rate is high and rotational speed is not high enough, therefore, there is slightly macrosegregation trend for the alloy element of Al and V in the wedge-shape castings.

Historical Introduction

1977 ◽  
Vol 35 ◽  
pp. 2-5
Author(s):  
R. D. Heidenreich
Keyword(s):  
Electron Emission ◽  
Secondary Electron ◽  
Secondary Electron Emission ◽  
50Th Anniversary ◽  
Secondary Emission ◽  
Wave Nature ◽  
Nobel Prize In Physics ◽  
Primary Electrons ◽  
The U.S ◽  
Mutual Agreement

This program has been organized by the EMSA to commensurate the 50th anniversary of the experimental verification of the wave nature of the electron. Davisson and Germer in the U.S. and Thomson and Reid in Britian accomplished this at about the same time. Their findings were published in Nature in 1927 by mutual agreement since their independent efforts had led to the same conclusion at about the same time. In 1937 Davisson and Thomson shared the Nobel Prize in physics for demonstrating the wave nature of the electron deduced in 1924 by Louis de Broglie.The Davisson experiments (1921-1927) were concerned with the angular distribution of secondary electron emission from nickel surfaces produced by 150 volt primary electrons. The motivation was the effect of secondary emission on the characteristics of vacuum tubes but significant deviations from the results expected for a corpuscular electron led to a diffraction interpretation suggested by Elasser in 1925.

Scanning Electron Microscopy-cuticular Lesions on the Roundworm Ascaris Suum

1970 ◽  
Vol 28 ◽  
pp. 114-115
Author(s):  
P. A. Madden ◽  
W. R. Anderson
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Freeze Drying ◽  
Room Temperature ◽  
Secondary Electron ◽  
Distilled Water ◽  
Freeze Dried ◽  
Silver Paint ◽  
To Come ◽  
Scanning Electron

The intestinal roundworm of swine is pinkish in color and about the diameter of a lead pencil. Adult worms, taken from parasitized swine, frequently were observed with macroscopic lesions on their cuticule. Those possessing such lesions were rinsed in distilled water, and cylindrical segments of the affected areas were removed. Some of the segments were fixed in buffered formalin before freeze-drying; others were freeze-dried immediately. Initially, specimens were quenched in liquid freon followed by immersion in liquid nitrogen. They were then placed in ampuoles in a freezer at −45C and sublimated by vacuum until dry. After the specimens appeared dry, the freezer was allowed to come to room temperature slowly while the vacuum was maintained. The dried specimens were attached to metal pegs with conductive silver paint and placed in a vacuum evaporator on a rotating tilting stage. They were then coated by evaporating an alloy of 20% palladium and 80% gold to a thickness of approximately 300 A°. The specimens were examined by secondary electron emmission in a scanning electron microscope.

SEM and Auger microanalysis studies of Cu-Be dynode surfaces at each activation condition

1978 ◽  
Vol 36 (1) ◽  
pp. 524-525
Author(s):  
T. Koshikawa ◽  
Y. Fujii ◽  
E. Sugata ◽  
F. Kanematsu
Keyword(s):  
Electron Emission ◽  
Secondary Electron ◽  
Secondary Electron Emission ◽  
Life Time ◽  
Activation Process ◽  
Beam Diameter ◽  
Activation Temperature ◽  
Electron Multiplier ◽  
Activation Condition ◽  
Activation Conditions

The Cu-Be alloys are widely used as the electron multiplier dynodes after the adequate activation process. But the structures and compositions of the elements on the activated surfaces were not studied clearly. The Cu-Be alloys are heated in the oxygen atmosphere in the usual activation techniques. The activation conditions, e.g. temperature and O2 pressure, affect strongly the secondary electron yield and life time of dynodes.In the present paper, the activated Cu-Be dynode surfaces at each condition are investigated with Scanning Auger Microanalyzer (SAM) (primary beam diameter: 3μmϕ) and SEM. The commercial Cu-Be(2%) alloys were polished with Cr2O3 powder, rinsed in the distilled water and set in the vacuum furnance.Two typical activation condition, i.e. activation temperature 730°C and 810°C in 5x10-3 Torr O2 pressure were chosen since the formation mechanism of the BeO film on the Cu-Be alloys was guessed to be very different at each temperature from the results of the secondary electron emission measurements.

SEM analysis of DC magnetron sputtered beryllium films

1988 ◽  
Vol 46 ◽  
pp. 960-961
Author(s):  
E. F. Lindsey ◽  
C. W. Price ◽  
E. L. Pierce ◽  
E. J. Hsieh
Keyword(s):  
Fine Structure ◽  
Electron Emission ◽  
Secondary Electron ◽  
Low Voltage ◽  
Ion Beam ◽  
Secondary Electron Emission ◽  
Sem Analysis ◽  
Fused Silica ◽  
Grain Structure ◽  
Silica Substrate

Columnar structures produced by DC magnetron sputtering can be altered by using RF biased sputtering or by exposing the film to nitrogen pulses during sputtering, and these techniques are being evaluated to refine the grain structure in sputtered beryllium films deposited on fused silica substrates. Beryllium is brittle, and fractures in sputtered beryllium films tend to be intergranular; therefore, a convenient technique to analyze grain structure in these films is to fracture the coated specimens and examine them in an SEM. However, fine structure in sputtered deposits is difficult to image in an SEM, and both the low density and the low secondary electron emission coefficient of beryllium seriously compound this problem. Secondary electron emission can be improved by coating beryllium with Au or Au-Pd, and coating also was required to overcome severe charging of the fused silica substrate even at low voltage. The coating structure can obliterate much of the fine structure in beryllium films, but reasonable results were obtained by using the high-resolution capability of an Hitachi S-800 SEM and either ion-beam coating with Au-Pd or carbon coating by thermal evaporation.

Sign in / Sign up

Export Citation Format

Share Document