High-Vacuum Evaporation Stage for an Electron Microscope

1970 ◽  
Vol 7 (1) ◽  
pp. 164-168 ◽  
Author(s):  
D. N. Braski
Keyword(s):  
Electron Microscope ◽  
High Vacuum ◽  
Vacuum Evaporation ◽  
Evaporation Stage

Demonstration of the Use of Tape-Recorded Information from a High Vacuum Electron Microscope

1969 ◽  
Vol 27 ◽  
pp. 218-219
Author(s):  
Richard E. Hartman ◽  
Roberta S. Hartman ◽  
Peter L. Ramos
Keyword(s):  
Information Retrieval ◽  
Electron Microscope ◽  
Magnetic Tape ◽  
High Vacuum ◽  
Data Retrieval ◽  
Electronic Information ◽  
Electronic Data ◽  
Subsequent Processing ◽  
Continuous Record

We have long felt that some form of electronic information retrieval would be more desirable than conventional photographic methods in a high vacuum electron microscope for various reasons. The most obvious of these is the fact that with electronic data retrieval the major source of gas load is removed from the instrument. An equally important reason is that if any subsequent analysis of the data is to be made, a continuous record on magnetic tape gives a much larger quantity of data and gives it in a form far more satisfactory for subsequent processing.

The High Resolution Scanning Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 316-317
Author(s):  
A. V. Crewe
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
High Vacuum ◽  
Scanning Transmission Electron Microscope ◽  
Ultra High Vacuum ◽  
Resolving Power ◽  
Imaging Characteristics ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
The Moment

The high resolution STEM is now a fact of life. I think that we have, in the last few years, demonstrated that this instrument is capable of the same resolving power as a CEM but is sufficiently different in its imaging characteristics to offer some real advantages.It seems possible to prove in a quite general way that only a field emission source can give adequate intensity for the highest resolution^ and at the moment this means operating at ultra high vacuum levels. Our experience, however, is that neither the source nor the vacuum are difficult to manage and indeed are simpler than many other systems and substantially trouble-free.

Vacuum System to Minimize the Specimen Contamination of High-Performance EM

1977 ◽  
Vol 35 ◽  
pp. 68-69
Author(s):  
N. Yoshimura ◽  
K. Shirota ◽  
T. Etoh
Keyword(s):  
Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
High Vacuum ◽  
Vacuum System ◽  
Pump System ◽  
Pumping System ◽  
Diffusion Pump ◽  
Almost All ◽  
Cascade Type

One of the most important requirements for a high-performance EM, especially an analytical EM using a fine beam probe, is to prevent specimen contamination by providing a clean high vacuum in the vicinity of the specimen. However, in almost all commercial EMs, the pressure in the vicinity of the specimen under observation is usually more than ten times higher than the pressure measured at the punping line. The EM column inevitably requires the use of greased Viton O-rings for fine movement, and specimens and films need to be exchanged frequently and several attachments may also be exchanged. For these reasons, a high speed pumping system, as well as a clean vacuum system, is now required. A newly developed electron microscope, the JEM-100CX features clean high vacuum in the vicinity of the specimen, realized by the use of a CASCADE type diffusion pump system which has been essentially improved over its predeces- sorD employed on the JEM-100C.

A Field Emission System For Transmission Electron Microscopy

1973 ◽  
Vol 31 ◽  
pp. 298-299
Author(s):  
Michel Troyonal ◽  
Huei Pei Kuoal ◽  
Benjamin M. Siegelal
Keyword(s):  
Electron Microscope ◽  
Field Emission ◽  
Optical System ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Objective Lens ◽  
Electron Optical System ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Emission System

A field emission system for our experimental ultra high vacuum electron microscope has been designed, constructed and tested. The electron optical system is based on the prototype whose performance has already been reported. A cross-sectional schematic illustrating the field emission source, preaccelerator lens and accelerator is given in Fig. 1. This field emission system is designed to be used with an electron microscope operated at 100-150kV in the conventional transmission mode. The electron optical system used to control the imaging of the field emission beam on the specimen consists of a weak condenser lens and the pre-field of a strong objective lens. The pre-accelerator lens is an einzel lens and is operated together with the accelerator in the constant angular magnification mode (CAM).

High-Vacuum Evaporation and a Cryostage to Observe Fractured Yeast

1988 ◽  
Vol 46 ◽  
pp. 256-257
Author(s):  
William P. Wergin ◽  
Eric F. Erbe ◽  
Eugene L. Vigil
Keyword(s):  
Electron Microscope ◽  
Low Temperature ◽  
Standard Specimen ◽  
High Vacuum ◽  
Specimen Holder ◽  
Sputter Coating ◽  
Fresh Frozen ◽  
Gain Access ◽  
Scanning Electron ◽  
Transfer Device

Investigators have long realized the potential advantages of using a low temperature (LT) stage to examine fresh, frozen specimens in a scanning electron microscope (SEM). However, long working distances (W.D.), thick sputter coatings and surface contamination have prevented LTSEM from achieving results comparable to those from TEM freeze etch. To improve results, we recently modified techniques that involve a Hitachi S570 SEM, an Emscope SP2000 Sputter Cryo System and a Denton freeze etch unit. Because investigators have frequently utilized the fractured E face of the plasmalemma of yeast, this tissue was selected as a standard for comparison in the present study.In place of a standard specimen holder, a modified rivet was used to achieve a shorter W.D. (1 to -2 mm) and to gain access to the upper detector. However, the additional height afforded by the rivet, precluded use of the standard shroud on the Emscope specimen transfer device. Consequently, the sample became heavily contaminated (Fig. 1). A removable shroud was devised and used to reduce contamination (Fig. 2), but the specimen lacked clean fractured edges. This result suggested that low vacuum sputter coating was also limiting resolution.

A Base Specific Single Heavy Atom Stain for Electron Microscopy

1972 ◽  
Vol 30 ◽  
pp. 184-185
Author(s):  
J. P. Langmore ◽  
N. R. Cozzarelli ◽  
A. V. Crewe
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
High Resolution ◽  
Elastic Scattering ◽  
Heavy Atom ◽  
High Vacuum ◽  
Heavy Atoms ◽  
Large Movement ◽  
Base Sequencing ◽  
Scanning Electron

A system has been developed to allow highly specific derivatization of the thymine bases of DNA with mercurial compounds wich should be visible in the high resolution scanning electron microscope. Three problems must be completely solved before this staining system will be useful for base sequencing by electron microscopy: 1) the staining must be shown to be highly specific for one base, 2) the stained DNA must remain intact in a high vacuum on a thin support film suitable for microscopy, 3) the arrangement of heavy atoms on the DNA must be determined by the elastic scattering of electrons in the microscope without loss or large movement of heavy atoms.

Electrostatic optics and aberration correction in the 1940s and today

1992 ◽  
Vol 50 (1) ◽  
pp. 6-7
Author(s):  
Gertrude F. Rempfer
Keyword(s):  
Electron Microscope ◽  
Focal Point ◽  
Focal Length ◽  
High Vacuum ◽  
Electron Optics ◽  
Applied Physics ◽  
Electrostatic Lenses ◽  
Commercial Instrument ◽  
The University ◽  
Theory And Experiment

I became involved in electron optics in early 1945, when my husband Robert and I were hired by the Farrand Optical Company. My husband had a mathematics Ph.D.; my degree was in physics. My main responsibilities were connected with the development of an electrostatic electron microscope. Fortunately, my thesis research on thermionic and field emission, in the late 1930s under the direction of Professor Joseph E. Henderson at the University of Washington, provided a foundation for dealing with electron beams, high vacuum, and high voltage.At the Farrand Company my co-workers and I used an electron-optical bench to carry out an extensive series of tests on three-electrode electrostatic lenses, as a function of geometrical and voltage parameters. Our studies enabled us to select optimum designs for the lenses in the electron microscope. We early on discovered that, in general, electron lenses are not “thin” lenses, and that aberrations of focal point and aberrations of focal length are not the same. I found electron optics to be an intriguing blend of theory and experiment. A laboratory version of the electron microscope was built and tested, and a report was given at the December 1947 EMSA meeting. The micrograph in fig. 1 is one of several which were presented at the meeting. This micrograph also appeared on the cover of the January 1949 issue of Journal of Applied Physics. These were exciting times in electron microscopy; it seemed that almost everything that happened was new. Our opportunities to publish were limited to patents because Mr. Farrand envisaged a commercial instrument. Regrettably, a commercial version of our laboratory microscope was not produced.

Universal ESEM

1993 ◽  
Vol 51 ◽  
pp. 786-787
Author(s):  
G.D. Danilatos
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
High Vacuum ◽  
Natural Extension ◽  
Necessary Condition ◽  
Environmental Scanning ◽  
Detection Systems ◽  
Small Gain ◽  
Detection Medium ◽  
Scanning Electron

The environmental scanning electron microscope (ESEM) has evolved as the natural extension of the scanning electron microscope (SEM), both historically and technologically. ESEM allows the introduction of a gaseous environment in the specimen chamber, whereas SEM operates in vacuum. One of the detection systems in ESEM, namely, the gaseous detection device (GDD) is based on the presence of gas as a detection medium. This might be interpreted as a necessary condition for the ESEM to remain operational and, hence, one might have to change instruments for operation at low or high vacuum. Initially, we may maintain the presence of a conventional secondary electron (E-T) detector in a "stand-by" position to switch on when the vacuum becomes satisfactory for its operation. However, the "rough" or "low vacuum" range of pressure may still be considered as inaccessible by both the GDD and the E-T detector, because the former has presumably very small gain and the latter still breaks down.

Mounting an individual submicrometer sized single crystal

1996 ◽  
Vol 211 (6) ◽  
Author(s):  
R. B. Neder ◽  
M. Burghammer ◽  
Th. Grasl ◽  
H. Schulz
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Single Crystal ◽  
Single Crystals ◽  
High Vacuum ◽  
Nanometer Resolution ◽  
Micro Manipulator ◽  
Scanning Electron

AbstractWe developed a new micro manipulator for mounting individual sub-micrometer sized single crystals within a scanning electron microscope. The translations are realized via a commercially available piezomicroscope, adapted for high vacuum usage and realize nanometer resolution. With this novel instrument it is routinely possible to mount individual single crystals with sizes down to 0.1

Sign in / Sign up

Export Citation Format

Share Document