Numerical Simulation of a Highly Compressed Saturated Water Flashing Flow

2017 ◽  
Author(s):  
Jong Chull Jo ◽  
Jae Jun Jeong ◽  
Byong Jo Yun ◽  
Frederick J. Moody
Keyword(s):  
High Pressure ◽  
Atmospheric Pressure ◽  
Saturated Vapor ◽  
Fluid Velocity ◽  
Saturated Liquid ◽  
Two Phase ◽  
Pressurized Water ◽  
Saturated Water ◽  
Outflow Boundary Condition ◽  
Inner Diameter

Transient fluid velocity and pressure fields in a pressurized water reactor (PWR) steam generator (SG) secondary side during the blowdown period of a feedwater line break (FWLB) accident were numerically simulated employing the saturated liquid flashing model. This model is based on the assumption that compressed water in the SG is saturated at the beginning and decompresses into the two-phase region where saturated vapor forms, creating a mixture of steam bubbles in liquid by bulk boiling. The numerical calculations were performed for two cases where the outflow boundary condition is different from each other; one is specified as the direct blowdown discharge to atmospheric pressure and the other is specified as the blowdown discharge to an extended calculation domain with atmospheric pressure on its boundary. To effectively simulate the saturated water flashing from the SG following the FWLB accident, the physical SG model was simplified as a vertical once-through SG to which a feedwater pipe is attached. However, the physical geometry of the analysis model was modeled as realistically as possible in terms of the SG tube bundle height, the SG inner diameter and porosity, the inner diameter and length of broken feedwater pipe part, etc. It was considered that the SG shell-side and the attached feedwater pipe were initially filled with high pressure saturated water. The pressure in the steam space was 7.5 MPa. For the calculation of the two-phase flow during high pressure saturated water flashing from the SG through the broken feedwater pipe, the inhomogeneous two-fluid model was used. The present simulation results were discussed through a comparison with the predictions using a simple non-flashing model neglecting the effects of phase change. Based on the comparative discussions, the applicability of each of the non-flashing liquid discharge and saturated liquid flashing discharge models to the confirmatory safety evaluations of new SG designs was examined.

Numerical analysis of bubble condensation behavior under high-pressure flow conditions

2020 ◽  
Vol 234 (18) ◽  
pp. 3725-3741
Author(s):  
SalaiSargunan S Paramanantham ◽  
Thanh-Hoang Phan ◽  
Warn-Gyu Park
Keyword(s):  
High Pressure ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Sensitivity Study ◽  
Transfer Model ◽  
Condensation Rate ◽  
Flow Conditions ◽  
Two Phase ◽  
Pressurized Water ◽  
Water Reactors

Heat transfer during subcooled flow boiling has a pivotal role in pressurized water reactors; it also occurs in boiling water reactors prior to the onset of saturated nucleate boiling. We examined the condensation behavior of vapor bubbles in the subcooled liquid phase using the fully compressible two-phase homogeneous mixture method, solved by an implicit dual-time preconditioned method. The continuous surface force method was applied to determine the surface tension between the phases in the simulation. To predict the empirical coefficient, we conducted a sensitivity study using Lee’s mass transfer model. For nuclear applications, we simulated high-pressure vapor–water conditions under higher mass flow conditions. The comparison of the numerical simulation and experimental results showed that the proposed model accurately predicted the condensation behavior of the bubble. Additionally, we investigated single bubble condensation behavior at different operating pressures, subcooling temperatures, bubble diameters, and bulk velocities. We also investigated the effects of high-pressure condensation on bubble shape. At lower subcooling temperatures, the condensation rate increased as pressure increased; however, at higher subcooling temperatures, pressure had no significant impact on the condensation rate.

Two-Phase Vessel Blowdown of an Initially Saturated Liquid—Part 1: Experimental

1983 ◽  
Vol 105 (4) ◽  
pp. 687-693 ◽  
Author(s):  
M. N. Hutcherson ◽  
R. E. Henry ◽  
D. E. Wollersheim
Keyword(s):  
Pressure Vessel ◽  
Large Diameter ◽  
Small Diameter ◽  
Nonuniform Distribution ◽  
Superheated Liquid ◽  
Critical Flow ◽  
Saturated Liquid ◽  
Two Phase ◽  
Saturated Water ◽  
Liquid Part

Experimental blowdown results for initially isothermal, saturated water from a small pressure vessel containing internal geometry are presented. This experiment simulated a break in a large duct of approximately three diameters in length which exited from the vessel. Choking only occurred at the exit of the discharge duct, and the instantaneous internal vessel pressure distribution was nearly uniform. Most of the fluid within the vessel immediately after the initiation of the blowdown became superheated liquid. This thermodynamic state together with the activated wall cavities inside the vessel maintained a nearly constant internal vessel pressure history early in the blowdown. However, in the latter stage of the depressurization, the remaining fluid within the vessel was essentially in thermodynamic equilibrium. A nonuniform distribution of fluid quality within the vessel was also detected in this experiment. In addition, this experiment illustrates that transient, two-phase, critical flow in large diameter ducts is similar to steady, two-phase, critical flow in small diameter ducts.

scholarly journals The erosion wear mechanism of liquid-solid two-phase high pressure manifold tee pipes

2021 ◽  
Vol 37 (1) ◽  
Author(s):  
H. Zhang ◽  
J. Zhang ◽  
L. Lv
Keyword(s):  
High Pressure ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Wear Mechanism ◽  
Erosion Rate ◽  
Fluid Velocity ◽  
Erosion Wear ◽  
Two Phase ◽  
Geometry Model ◽  
Wall Shear

The wall thickness of pressure pipe is often thinned due to the erosion wear, which leads to pipe failure and even safety accidents. In particular, the tee pipe is more prone to be erosive as a key component of transferring fluid with particles. Therefore, the erosion wear mechanism of high pressure manifold tee pipe based on liquid-solid two-phase flow is studied in this paper. Firstly, the standard tee pipe geometry model is established and the grid is divided. And then grid number independence is verified by the percentage difference. According to the structural characteristics of tee pipe, the wear of the inner wall under four different port combinations is predicted. In addition, the relationship between erosion rate and wall shear stress is further analyzed by fluid velocity, particle diameter and mass flow rate. Double tee pipes geometry model was established to explore the erosion wear on the inner walls. The effects of assembly length and different port combinations on erosion wear were discussed respectively. When the inlets are fixed, the wall shear stress distribution of the downstream tee pipe is mainly affected by the outlets. The assembly length mainly affects the erosion rate of the downstream tee pipe.

Cyclone Bomb hits Southern Brazil in 2020

2020 ◽  
Vol 3 (3) ◽  
Author(s):  
Ricardo Gobato ◽  
Alireza Heidari
Keyword(s):  
High Pressure ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Satellite Images ◽  
The State ◽  
Southern Brazil ◽  
Santa Catarina ◽  
High Area ◽  
South Of Brazil ◽  
Rapid Drop

An “explosive extratropical cyclone” is an atmospheric phenomenon that occurs when there is a very rapid drop in central atmospheric pressure. This phenomenon, with its characteristic of rapidly lowering the pressure in its interior, generates very intense winds and for this reason it is called explosive cyclone, bomb cyclone. With gusts recorded of 116 km/h, atmospheric phenomenon – “cyclone bomb” (CB) hit southern Brazil on June 30, the beginning of winter 2020, causing destruction in its influence over. One of the cities most affected was Chapecó, west of the state of Santa Catarina. The satellite images show that the CB generated a low pressure (976 mbar) inside it, generating two atmospheric currents that moved at high speed. In a northwest-southeast direction, Bolivia and Paraguay, crossing the states of Parana and Santa Catarina, and this draft that hit the south of Brazil, which caused the destruction of the affected states.  Another moving to Argentina, southwest-northeast direction, due to high area of high pressure (1022 mbar). Both enhanced the phenomenon.

Features of spatial shock-wave flows in vapor-gas-liquid mixtures

2014 ◽  
Vol 10 ◽  
pp. 27-31
Author(s):  
R.Kh. Bolotnova ◽  
U.O. Agisheva ◽  
V.A. Buzina
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Shock Waves ◽  
Liquid Mixture ◽  
Liquid Mixtures ◽  
Pressure Vessels ◽  
Water Mixture ◽  
Two Dimensional ◽  
Nonstationary Processes ◽  
Two Phase

The two-phase model of vapor-gas-liquid medium in axisymmetric two-dimensional formulation, taking into account vaporization is constructed. The nonstationary processes of boiling vapor-water mixture outflow from high-pressure vessels as a result of depressurization are studied. The problems of shock waves action on filled by gas-liquid mixture volumes are solved.

Investigation of two-dimensional nonstationary processes of outflow a gas-saturated liquid from axisymmetric vessels

2012 ◽  
Vol 9 (1) ◽  
pp. 47-52
Author(s):  
R.Kh. Bolotnova ◽  
V.A. Buzina
Keyword(s):  
Comparative Analysis ◽  
Numerical Model ◽  
Liquid Mixture ◽  
Phase Model ◽  
Test Problems ◽  
Two Dimensional ◽  
Nonstationary Processes ◽  
Saturated Liquid ◽  
Two Phase ◽  
One Dimensional

The two-dimensional and two-phase model of the gas-liquid mixture is constructed. The validity of numerical model realization is justified by using a comparative analysis of test problems solution with one-dimensional calculations. The regularities of gas-saturated liquid outflow from axisymmetric vessels for different geometries are established.

scholarly journals Two-Phase Turbulence Statistics from High Fidelity Dispersed Droplet Flow Simulations in a Pressurized Water Reactor (PWR) Sub-Channel with Mixing Vanes

Fluids ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 72
Author(s):  
Nadish Saini ◽  
Igor A. Bolotnov
Keyword(s):  
Continuous Phase ◽  
System Level ◽  
Data Repository ◽  
High Fidelity ◽  
Turbulence Statistics ◽  
Two Phase ◽  
Pressurized Water ◽  
Droplet Dynamics ◽  
High Resolution Data ◽  
Spacer Grids

In the dispersed flow film boiling regime (DFFB), which exists under post-LOCA (loss-of-coolant accident) conditions in pressurized water reactors (PWRs), there is a complex interplay between droplet dynamics and turbulence in the surrounding steam. Experiments have accredited particular significance to droplet collision with the spacer-grids and mixing vane structures and their consequent positive feedback to the heat transfer recorded in the immediate downstream vicinity. Enabled by high-performance computing (HPC) systems and a massively parallel finite element-based flow solver—PHASTA (Parallel Hierarchic Adaptive Stabilized Transient Analysis)—this work presents high fidelity interface capturing, two-phase, adiabatic simulations in a PWR sub-channel with spacer grids and mixing vanes. Selected flow conditions for the simulations are informed by the experimental data found in the literature, including the steam Reynolds number and collision Weber number (Wec={40,80}), and are characteristic of the DFFB regime. Data were collected from the simulations at an unprecedented resolution, which provides detailed insights into the continuous phase turbulence statistics, highlighting the effects of the presence of droplets and the comparative effect of different Weber numbers on turbulence in the surrounding steam. Further, axial evolution of droplet dynamics was analyzed through cross-sectionally averaged quantities, including droplet volume, surface area and Sauter mean diameter (SMD). The downstream SMD values agree well with the existing empirical correlations for the selected range of Wec. The high-resolution data repository from the simulations herein is expected to be of significance to guide model development for system-level thermal hydraulic codes.

Experimental Characterization of a Modified Airlift Pump

2014 ◽  
Author(s):  
Afshin Goharzadeh ◽  
Keegan Fernandes
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Water Flow Rate ◽  
High Speed Photography ◽  
Two Phase ◽  
Inner Diameter ◽  
Airlift Pump ◽  
Flow Map ◽  
Churn Flow

This paper presents an experimental investigation on a modified airlift pump. Experiments were undertaken as a function of air-water flow rate for two submergence ratios (ε=0.58 and 0.74), and two different riser geometries (i) straight pipe with a constant inner diameter of 19 mm and (ii) enlarged pipe with a sudden expanded diameter of 19 to 32 mm. These transparent vertical pipes, of 1 m length, were submerged in a transparent rectangular tank (0.45×0.45×1.1 m3). The compressed air was injected into the vertical pipe to lift the water from the reservoir. The flow map regime is established for both configurations and compared with previous studies. The two phase air-water flow structure at the expansion region is experimentally characterized. Pipeline geometry is found to have a significant influence on the output water flow rate. Using high speed photography and electrical conductivity probes, new flow regimes, such as “slug to churn” and “annular to churn” flow, are observed and their influence on the output water flow rate and efficiency are discussed. These experimental results provide fundamental insights into the physics of modified airlift pump.

PHASE TRANSITION IN LAYERED PEROVSKITE LIKE MANGANATE Ca3Mn2O7 UNDER HIGH PRESSURE

2001 ◽  
Vol 15 (18) ◽  
pp. 2491-2497 ◽  
Author(s):  
J. L. ZHU ◽  
L. C. CHEN ◽  
R. C. YU ◽  
F. Y. LI ◽  
J. LIU ◽  
...  
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
Diamond Anvil Cell ◽  
The Other ◽  
Layered Perovskite ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Diamond Anvil

In situ high pressure energy dispersive X-ray diffraction measurements on layered perovskite-like manganate Ca 3 Mn 2 O 7 under pressures up to 35 GPa have been performed by using diamond anvil cell with synchrotron radiation. The results show that the structure of layered perovskite-like manganate Ca 3 Mn 2 O 7 is unstable under pressure due to the easy compression of NaCl-type blocks. The structure of Ca 3 Mn 2 O 7 underwent two phase transitions under pressures in the range of 0~35 GPa. One was at about 1.3 GPa with the crystal structure changing from tetragonal to orthorhombic. The other was at about 9.5 GPa with the crystal structure changing from orthorhombic back to another tetragonal.

scholarly journals Transparent and Inexpensive Microfluidic Device for Two-Phase Flow Systems with High-Pressure Performance

2014 ◽  
Vol 37 (11) ◽  
pp. 1929-1937 ◽  
Author(s):  
Nayane Macedo Portela da Silva ◽  
Jean-Jacques Letourneau ◽  
Fabienne Espitalier ◽  
Laurent Prat
Keyword(s):  
High Pressure ◽  
Microfluidic Device ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Systems
Sign in / Sign up

Export Citation Format

Share Document